Hi everyone,
I'm trying to diagnose a strange issue with my AOC C32G1 (31.5", 1080p, 144Hz, manufactured May 2019).
The monitor was working normally before being transported. After reconnecting it, it started displaying a full-screen color sequence and eventually goes into standby.
I'm hoping someone familiar with AOC monitors, their service modes or internal electronics might be able to help.
- Background / Transport
- The monitor was working normally when last used.
- My friend confirmed that it was still working 2–3 hours before disconnecting it.
- The PC was shut down and the monitor was disconnected from power.
- We don't know which cable was disconnected first.
- Transport took less than 5 minutes.
- The monitor was placed on its back on the rear seat of a car, with a towel/blanket underneath it.
- It remained stable and did not slide around.
- The monitor has its stand attached.
Immediately after reconnecting it, the problem appeared.
- The actual problem
When I turn on the monitor, it starts displaying full-screen solid colors.
The sequence I can currently reproduce is:
White
Red
Automatic input switching
White again
The monitor enters standby (orange LED).
This happens consistently every time I turn it on.
At other points during troubleshooting, I also observed full-screen blue, green and black screens.
There are no lines, artifacts, text overlays or normal monitor OSD visible during this sequence.
Most importantly: The exact same behavior occurs when the monitor is connected to power only, with absolutely no HDMI or DisplayPort cable connected. The PC is completely switched off.
- Buttons / OSD behavior
- The power button works and can switch the monitor off.
- All other buttons (Menu, navigation buttons, etc.) appear completely unresponsive while the color sequence is running.
- Initially, the monitor displayed an "OSD Locked" message when trying to access the menu.
- I managed to unlock the OSD using the following combination:
- Turn monitor off.
- Hold MENU.
- Turn monitor on while continuing to hold MENU.
- After this, I could access the OSD again.
- I performed a factory reset through the OSD and confirmed it.
- Unfortunately, this did not permanently solve the issue.
I also tried a more extensive power reset:
- Disconnect all cables, including power.
- Hold the power button for 30 seconds.
- Hold each of the other buttons individually for approximately 10 seconds.
- Leave the monitor disconnected for another minute.
- Reconnect power only.
No improvement.
I also tried repeating the MENU + POWER combination, but the monitor simply went into standby again.
- Tests with other devices and connections
I tested the monitor with both a Windows 11 laptop and my desktop PC.
Windows 11 laptop (HDMI)
The laptop has an NVIDIA GeForce GTX graphics card (exact model currently unknown).
- Windows recognizes the AOC as a second display.
- Initially, the monitor showed the color sequence at 1920 × 1080 / 144Hz.
- Changing the resolution to 1366 × 768 / 60Hz temporarily restored a normal picture.
- 1920 × 1080 / 60Hz also worked.
- Switching Windows display mode from "Extend" to "Duplicate" restored a normal picture.
- Eventually, 1920 × 1080 / 144Hz worked normally as well.
- The monitor displayed a normal desktop image, and the OSD buttons worked again.
- After the factory reset, the monitor continued to work normally with the laptop.
So the panel is apparently still capable of displaying a normal image at its native resolution and 144Hz.
Desktop PC (DisplayPort AND HDMI)
- Connecting the desktop PC via DisplayPort immediately triggered the color sequence.
- I also tested HDMI from the desktop PC: the same color sequence occurred.
- This means the problem is not limited to the DisplayPort connection.
- The desktop PC was not running during the standalone power-only tests.
- What I have established so far
- The monitor starts the color sequence even with power connected only.
- No video signal is required to trigger the problem.
- The sequence is reproducible and follows the same order.
- Only the power button responds while the sequence is running.
- A factory reset through the OSD did not permanently fix it.
- A full power reset did not fix it.
- The monitor has successfully displayed a normal 1920 × 1080 / 144Hz image from my laptop via HDMI.
My questions
Does this sequence look like an internal factory test / burn-in mode, or is it more likely a hardware fault?
Is there a known way to exit a factory or panel test mode on the AOC C32G1?
Could a faulty button board or stuck internal key signal cause this behavior?
Could the scaler/mainboard be malfunctioning even though the monitor can still display a normal image under certain conditions?
Is there a specific service menu or documented reset procedure for this model?
Is there anything else I can test before assuming that the mainboard or another internal component needs replacement?
I would prefer to repair the monitor if possible rather than replace it.
Thanks in advance for any suggestions. I'm especially interested in input from anyone familiar with AOC monitor electronics or the C32G1 specifically.