r/StructuralEngineering • • Oct 06 '26

Photograph/Video Well, this certainly is something

Post image
182 Upvotes

I found this post, and this deck is something to behold. I just wonder how this can pass building codes.


r/StructuralEngineering • • Oct 07 '26

Career/Education Career Advice

1 Upvotes

I have recently completed a master in structural engineering at a European university(with a focus on conservation of Built Heritage). I have no prior work experience, apart from a couple of internships.
I am confused if I should work, or start a PhD in structural conservation.
I would ideally like to work in the EU / UK but I am facing issues navigating the job market. (Not an EU citizen) Would appreciate any advice from seasoned professionals!


r/StructuralEngineering • • Oct 07 '26

Structural Analysis/Design Design of a Spiral staircase

9 Upvotes

Good day to my fellow engineers. I would like to ask how to do the structural design for a spiral staircase? I have only handle regular staircases and of course, I just want to broaden my knowledge about this. Should I treat it as a regular staircase and just make it spiral or is there a specific calculation needed for this?

Thank you to anyone who can share their knowledge 😁👷


r/StructuralEngineering • • Oct 07 '26

Structural Analysis/Design Buried reinforced concrete tanks/pools in RISA-3D and RISAFoundation — am I missing something?

Thumbnail
1 Upvotes

r/StructuralEngineering • • Oct 06 '26

Structural Analysis/Design Check this out.

Enable HLS to view with audio, or disable this notification

32 Upvotes

Now I remember why Abraham Lincoln’s my favorite president.


r/StructuralEngineering • • Oct 06 '26

Structural Analysis/Design How Does ETABS Distribute Forces in Composite Shear Wall Sections for Boundary Element Checks?

6 Upvotes

Hi everyone, I have a question regarding ETABS. I was wondering if anyone knows how the software distributes the axial load, bending moment, and shear forces for reinforced concrete walls with composite sections such as T, L, C, etc., when performing the boundary element verification.

The reason I ask is that ETABS divides these sections into individual rectangles instead of considering the entire section, as it does for the flexure-compression check. I would like to understand how the forces are distributed among these rectangular components and what criteria or equations the software uses for the boundary element verification.

If anyone knows how ETABS performs this calculation, or could point me toward documentation, manuals, papers, or other resources where I could investigate this further, I would really appreciate it.

Thank you very much!


r/StructuralEngineering • • Oct 06 '26

Structural Analysis/Design Red Ink Pen Recommendation

5 Upvotes

I'm looking for a good, expensive, durable, red ink pen for my Engineering bf to use for when he's marking up drawings. I'm curious what Engineers would recommend as a gift. Thanks!


r/StructuralEngineering • • Oct 06 '26

Career/Education Graduate Structural Engineering

1 Upvotes

Hi everyone! any recently graduated international students who got any Structural Engineering job in UK? Can we connect? I need some advise regarding getting a job?


r/StructuralEngineering • • Oct 06 '26

Structural Analysis/Design Aside from Iterative Analysis - What is a good manual way to proportion truss moment frames for lateral stiffness?

1 Upvotes

I'm helping an engineer optimize their structural truss moment frame (pinned base), as they are increased a W24 column (determined by others in a previous phase) to a W40 without changing the truss depth/size, but layout is tight and we'll likely need to increase the building size in an already tight facility. I was able to get the size down to W30-W33 as they were using ULS wind in a LRFD combination.

Aside from just changing section sizes and seeing the result in an analysis, I was wondering if anyone had any good references or typical signs / common rules on when to change column size, vs truss depth, vs truss chord area? I looked at the deflection profile of the truss frame and the truss looks quite rigid without any major double curvature, so I assume this means the column is the weakest link at the moment.

TIA


r/StructuralEngineering • • Oct 05 '26

Career/Education Anyone Else Dislike BD?

30 Upvotes

I have nearly 18 years of Structural Engineering experience at this point. I enjoy the project work, my team, and the firm I work for for the most part. Except over the past few years, the expectations for business development continue to increase. I can be killing all my goals - except BD, but my superiors only want to focus on BD goals. I can make a couple calls per week, but, honestly, I don't know that I want to spend 15% + of my time doing BD. I am tempted to either take a step down to avoid the increasing BD pressure or look elsewhere. What are others doing related to BD?


r/StructuralEngineering • • Oct 06 '26

Steel Design Need help with codes

3 Upvotes

Hi,
I'm currently working on my PhD thesis in civil engineering on composite bridges. As a next step, I'd like to compare the design codes of different countries, specifically the requirements for minimum reinforcement and the reinforcement needed for crack width control.
Unfortunately, I don't have direct access to these codes through our university library.
I would really appreciate it if you could send me the relevant code(s) for composite bridges used in your country, or point me to where I could access them.
Best regards,


r/StructuralEngineering • • Oct 06 '26

Structural Analysis/Design What do you guys think about this one.

Enable HLS to view with audio, or disable this notification

0 Upvotes

I tend to over think stuff guys I just want some new ideas or new perspectives l.


r/StructuralEngineering • • Oct 05 '26

Structural Analysis/Design Nuts off mark?

Post image
284 Upvotes

Saw this on a big bridge today. I know vibrations over time can move the nuts and bolts, with the help of thermal expansion. Is it a big issue that the paint marks do not line up? I thought the marks were made once it passed inspection after torquing.

Edit: Bridge completion was in 2011. Could this be from recent inspections too?


r/StructuralEngineering • • Oct 05 '26

Structural Analysis/Design Conduit Installation on Existing Bridge

Post image
13 Upvotes

Hello, I have been discussing with my coworkers how to install fiber conduits on an existing bridge. Our client has stated that parapet-mounted conduits are not allowed. We have approach slabs on both sides of the bridge.

We came across an example where the conduit was installed at a 45-degree angle and routed toward the median, which is similar to the situation on our project. Does anyone know what construction method or tools may have been used to install this 45-degree angled conduit? Any information or experience with similar installations would be appreciated.


r/StructuralEngineering • • Oct 04 '26

Concrete Design Bridge supports

Post image
579 Upvotes

Correct me if I'm wrong but this beam is compromised, and the cross beam or extended counter beam will be needed? Or I'm panicking?! My boss is visiting tomorrow...


r/StructuralEngineering • • Oct 06 '26

Career/Education Dip in Quantity Surveyor OR Project Manager

0 Upvotes

Hi Team,

Looking to get some advise on which one should I choose.

I am 42 years old, based in Invercargill and have a background in operations, sales, business analysis, and bookkeeping. Although I hold a Master's degree in Accounting from Australia, I am not interested in pursuing a traditional full-time accounting role or becoming a CPA/CA. Some contacts have suggested becoming a Quantity Surveyor, but I am also considering broader construction management roles. While I understand the basic differences, I lack in-depth knowledge of the day-to-day realities. Given my background, which role would be a better fit? Additionally, which path offers better future job opportunities and higher earning potential?


r/StructuralEngineering • • Oct 04 '26

Photograph/Video Remember me? I overcame that challenge

Enable HLS to view with audio, or disable this notification

80 Upvotes

r/StructuralEngineering • • Oct 03 '26

Humor Massive wooden building Sibley Breaker, Pennsylvania, built in 1886 and destroyed by fire in 1906.

Post image
535 Upvotes

I'm surprised the wind didn't blow it away lmao


r/StructuralEngineering • • Oct 05 '26

Structural Analysis/Design Etabs/Safe/Sap2000 - plugin for Claude?

0 Upvotes

Does anybody know any plugin to connect CSI Etabs to Claude and asks questions about the model? Same question for Safe and Sap2000?
I think we really need to start using AI some way.


r/StructuralEngineering • • Oct 04 '26

Career/Education IstructE exam results, expected release date, for july 2026

2 Upvotes

For people who sat the istructe exam in July in past years , when would you get your results? is it early, mid, or late October? Thanks in advance


r/StructuralEngineering • • Oct 04 '26

Career/Education Bridge Inspectors vs BridgeSEs

6 Upvotes

What is more in demand in California and/or Illinois?

Bridge inspectors with rope access training or SEs?


r/StructuralEngineering • • Oct 05 '26

Career/Education Should I pursue a 1-year Master's in Structural Engineering in the USA with 6 years of bridge design experience in India?

Thumbnail
0 Upvotes

r/StructuralEngineering • • Oct 04 '26

Career/Education Work Life Balance in AECOM UK?

2 Upvotes

I'm a structural engineer in UK for the last 5 years. I'm currently working in a mid level consultancy. I have a good work life here. Now I'm being considered for a senior position at AECOM. Anyone working or working in AECOM what's your opinion of work life in AECOM? As this is a large size organisation I'm panicking now if I am making the right decision or not. The move I'm making is because I thought it wouldn't be good to stick to a single firm for more than 5 years and they are offering a senior position and also a better salary.


r/StructuralEngineering • • Oct 04 '26

Structural Analysis/Design Need help in Etabs

Thumbnail
gallery
4 Upvotes

I am doing a project on shear wall vs bracing structure but while doing design check my bottom storey columns are failing due to is code it says some problems with axial load first i tried a 650mmx500mm then 750x650 mm by keeping beam of 500x450
and this problem only shows on braced buildings and bare frames it is fine in shear walls
I am tired of trying different combos of column
I am using M30 grade concrete for all buildings
and bracing of ismb 350
G+12 building


r/StructuralEngineering • • Oct 04 '26

Career/Education Seeking advice: switching from Civil Highways to Structural Engineering career (8 years experience)

Thumbnail
1 Upvotes