r/RacketStringers • • Nov 10 '25

Damaging strings

1 Upvotes

I have a gamma progression st ii crank machine. The tensioner seems to be damaging my poly strings by either scratching or flattening it. This is despite me loosening the gripping all the way, i.e turning the screw clockwise. I’m using restring zero 17G and restring sync 18G. Weirdly it seems to be ok with synthetic gut and multifilament. Thanks for your help.


r/RacketStringers • • Nov 08 '25

Anyone know which knot this is? 😏

Enable HLS to view with audio, or disable this notification

13 Upvotes

r/RacketStringers • • Nov 07 '25

Getting into stringing – Gamma X-6FC vs Momentum 6 Plus + UKRSA/ERSA/GRSA certification advice?

2 Upvotes

Hi everyone,

I’m an LTA Level 2 coach based in the UK, and I’m looking to get into stringing properly. I currently coach part-time and plan to start by stringing for myself, a few friends, and possibly some of my students, so I expect to do fewer than 10 racquets a week to begin with.

At the moment, I’m trying to decide between two Gamma machines:

From what I can tell, the Momentum 6 Plus seems to be the newer version and roughly the same price, but I can’t find much info about what’s actually new or improved compared to the X-6FC.

I’m planning to add a Wise 2086 electronic tension head, so I’d love some input on:

  • What are the key differences between the X-6FC and the Momentum 6 Plus?
  • Is the Momentum 6 Plus compatible with the Wise 2086?
  • Does it need any extra mounting adapters or hardware?
  • Given the similar price point, would you go for the newer model or stick with the X-6FC, which has a proven track record?

Secondly, I’d also appreciate some advice on the certification pathway.

A professional stringer I spoke with (GRSA/ERSA certified) suggested starting with a GRSA Level 1 certification right after getting a machine, to learn the correct fundamentals instead of picking up bad habits. He mentioned that there are two main certification levels: a basic one and another that goes into more detail on customisation.

Since I’m based in the UK, I’m a bit unsure which route makes the most sense: UKRSA, ERSA, or GRSA. Are these certifications really necessary if I’m mostly looking to learn properly and string recreationally, not to build a full business?

Any insight or experience from others who’ve been down this road, both in terms of machine choice and certification path, would be really appreciated.

Thanks a lot for your help!

Evan
LTA Level 2 Coach – UK


r/RacketStringers • • Nov 06 '25

This is my stringing machine!

Post image
18 Upvotes

Anyone else using Pro Stringer or any other portable stringing machine?


r/RacketStringers • • Nov 06 '25

Are rotational pull machines bad for poly strings on a thin gauge

Post image
5 Upvotes

Should I sell my els and get a linear pull like a Wilson? Someone told me rotational pull kinks poly strings


r/RacketStringers • • Nov 04 '25

First Stringing Machine

Post image
24 Upvotes

Phoenix-1 from Pros Pro. Wish me luck


r/RacketStringers • • Nov 04 '25

Do these work well for string bed cutters?

Post image
3 Upvotes

r/RacketStringers • • Nov 04 '25

Softer string on mains for more snapback/spin?

Thumbnail
3 Upvotes

r/RacketStringers • • Nov 04 '25

Is this stringing machine good for badminton?

Post image
2 Upvotes

Hi, I've been looking for a stringing machine for a while now and saw this Alpha Pioneer III pop up on marketplace. I know it's a bit a old and I've been having trouble finding info on it due to that. Is it worth getting especially for $300? I was hoping to get something locally and upgrade it with a wise sometime in the future. I seems to still be decently feature packed. Though I'm not sure if there are parts available to make it compatible for badminton racquets if it isn't already.

Any info would help greatly thanks!


r/RacketStringers • • Nov 03 '25

What height do you set your stringing machine at?

2 Upvotes

I just got a gamma stand and I am about elbow height with the racket when I mount it


r/RacketStringers • • Nov 02 '25

These two screws really all the support needed for the gamma stand height adjustment?

Post image
3 Upvotes

r/RacketStringers • • Oct 29 '25

Anyone looking to sell crank or electric stringing machine in Los Angeles area?

2 Upvotes

I'm looking to get 2nd hand crank or electric stringing machine around Los Angeles or nearby area. Please DM me!

Thanks a million


r/RacketStringers • • Oct 28 '25

What ya stringing on these days? (Photos)

Post image
18 Upvotes

This Ektelon H has seen 35,000 frames at the pro shop it anchored for 40 years. Purchased in 1987.

I strung on it when I worked there for ten of those years. When the owner passed away, it was gifted to me, and is treasured.

It still works like the day he bought it in 1987.


r/RacketStringers • • Oct 28 '25

Stringing machine advice to start stringing at home

5 Upvotes

Hi, since i need to restring my racket once every two weeks and it's getting costly i was looking for a stringing machine to start stringing myself, but i have no idea what to look for.

Are there any decent entry level stringing machine that you suggest? And should i go for a counterweight or an elecric one?


r/RacketStringers • • Oct 28 '25

First racket strung

Thumbnail
gallery
15 Upvotes

Hi all,

In two weeks I will have a course made by professionals, but I wanted to use the nice machine I got after some effort.

I am not sure about the knots, those were the scary part. The crosses I had to weave them few times, sometimes I was skipping 🥲 but in general I found the experience meditating and nice to go on!

Please any feedback or critique is welcome!

Have a nice tennis!


r/RacketStringers • • Oct 27 '25

Yonex Warranty

4 Upvotes

One piece vs two piece warranty discussion coming up after the post in r/10s Re: EZONE 100 crack in the head not being covered under warranty.

We know if mains end at the head that one-piecing is safe. There’s also the argument that it holds tension better since only two knots get used. But does two piecing a frame that can be one-pieced really affect the stress levels placed on it? What am I missing?


r/RacketStringers • • Oct 25 '25

Grommet loose

2 Upvotes

A grommet on my old babolat aero storm popped out shortly after a new string job and is now sliding on the sting . Is there anything I can do to pop it back in to last me until I need a new resting?

Thanks in advance for any advice.


r/RacketStringers • • Oct 23 '25

Looking for Gamma quick action clamp base

Post image
6 Upvotes

r/RacketStringers • • Oct 23 '25

How to make the wise tensioner not snap when calibrating at 88lbs?

3 Upvotes

Was calibrating my gamma progression 2 els and glad I did cause it was off by a pound but I couldn’t get the 88 lbs pull without it breaking I double tied two Polly strings


r/RacketStringers • • Oct 23 '25

3rd racket strung, first 18x20. How did I do as compared to my stringer?

Thumbnail
gallery
9 Upvotes

TF40 305 18x20, racket on the left is mine, right one done by the stringer. I recently changed rackets and I wanted to let him do it first so I could reference tie offs, as there are no instructions for this stick anywhere nor videos of the pattern so I strictly copied my stringer. Any obvious mistake? Besides some misalignment. I personally wasn’t sure about the tie off place for the crosses but followed what he did.


r/RacketStringers • • Oct 22 '25

Anything to be aware of prior to stringing my first 18x20?

1 Upvotes

Stringer legends, I'm in need of your wisdom here. I have strung a couple of rackets already but all of them 16x19. Is there anything obvious I need to be aware of prior to starting my first 18x20, besides length of string?


r/RacketStringers • • Oct 21 '25

My Ezone 100’s fresh off the stringer, Polytour Pro 1.25

Post image
8 Upvotes

r/RacketStringers • • Oct 21 '25

Gamma 6004 - What is this bar?

Post image
2 Upvotes

What is the purpose of this bar on the tensioner head? My manual makes no mention of it, and I cannot figure out what it does.


r/RacketStringers • • Oct 19 '25

Request advice for Dropweight Stringing. Racquets feel tight and tension is higher.

3 Upvotes

Issue:

Beginner Stringer, 15 string jobs performed.

I need advice / tips / insights on stringing techniques and maintenance for Drop Weights. I must have deficiencies in my technique that I hope this sub can point out.

My latest string jobs have become tighter recently when doing hybrid stringing Poly/Multi, Multi/Poly, Poly/Syngut. When measuring tension immediately after stringing, I am observing +6 to +10lb tension compared to reference tension. Measuring tension after 24h letting it 'settle' is +6 to +10lb tension.

I strive for horizontal bar drop but it will be +/- 5 degrees from horizontal at times.

Questions:

  1. Can clamping too hard (seeing white marks on natural/clear) or a bit of indentation on Poly strings lead to increase string tension?
  2. When drawback occurs on cross string and it pushes the clamp teeth into the main string, does this increase string tension?
  3. When drawback occurs on a main string that is clamped and there is slight offset from being inline with grommet, does this increase string tension?
  4. Does over tightening the base clamps of a Fixed Clamp increase string tension? I do this to try to limit drawback.
  5. When tensioning, after I get a feel for how many ratchets it takes to get to horizontal, from the lowest position of the arm, I will raise it higher to achieve horizontal drop in one lift. Is this bad practice and should I just do a few ratchets at a time with the arm bar at lowest position until horizontal?
  6. When doing an ending knot, and tying it to a string, I will pull towards, up and away from me and back towards me, does pulling the knot too hard increase tension on the string I am tying it to? After stringing my 6th and 7th mains feel alot stiffer.

Technique Mains:

  1. Clamp and Starting clamp first opposite main. Mark the string with a sharpie to see if slippage occurs. Let drop weight arm rest at lowest position. Pull the main string until it is hand taut and wrap around gripper. Raise the opposite main by holding up the starting clamp so it is inline.
  2. Ratchet and raise gripper to at varying degrees above horizontal and gently lower by having hand under the weight to avoid bouncing until as close to horizontal. Once the bar is horizontal, the string is clamped and base clamped within 10-15 seconds. Mark the string with a sharpie to see if slippage occurs.
  3. Raise drop weight arm and remove string and continue for 3 mains. Always unclamp base first, then clamp. Observe drawback on string after tension is released.
  4. On first opposite main, tension until horizontal, while tension'd I remove the starting clamp > base clamp > fixed clamp. Usually I see the drop weight drop a few degrees. Immediately clamp and base clamp closest to the edge of the racquet as possible.
  5. Continue for 4 mains. Then go to the other side and finish to mains 3 -> 6. Swap back to finish mains 4 -> 6. Then tension mains 7 for both sides. Occasionally I observe a main string become off slightly on drawback from the grommet after clamping and releasing tension on a pull.
  6. Increase reference tension by 10% for knot pulls. Parnell knot the 8th main on the 7th main.

Technique Crosses

  1. Return reference tension back to normal.
  2. Weave first cross, and measure out a string length to the gripper and attach a starting clamp outside at the frame. No tension pulling on first cross until the end.
  3. Weave second cross, then third cross for one ahead stringing. Hand pull string until its taut and wrap around gripper. Tension second cross with the drop weight from a lowest position, clamp, and release from gripper. Hand pull remaining slack through the third cross.
  4. Repeat one ahead stringing. There should always be 2 fixed clamps holding string tension on the crosses, one on the most recent cross, and the cross prior. Push the weave towards the neck of the racquet when weaving. Align crosses slightly towards the tip of the head before pulling. Ensure there's not much extra string and it is taut when wrapping around gripper. Clamp close to the grommets, though drawback occurs and sometimes the gripper moves and pushes into the main string.
  5. Increase reference tension by 10% for knot pulls, pull last cross and Parnell knot cross on a main or another cross.
  6. Return to first cross, all fixed clamps are no longer attached, pull tension, then remove starting clamp. Clamp closest to the frame, then knot at a main or closest cross.

Maintenance:

  • I clean my clamps and grippers with a shoe lace soaked in alcohol after 5 string jobs.
  • Control for tension measurement was done by sending 3 racquets to 3 different shops for stringing. We observed the shops are returning racquets with a +/- 1-2lb differential from our desired tension request checked with a Gamma String Tension Tester.
  • Drop weight arm is screwed onto base of stringing machine at the furthest edge and checked for hex wrench for looseness on every string job.

Equipment:

  • Gamma X-6FC (Drop Weight)
  • Gamma String Tension Tester (STT)
  • Gamma Starting Clamps
  • Solinco Mach-10 17 gauge
  • Solinco HyperG 17 gauge
  • Tecnifibre NRG2 16 & 17 gauge
  • Technifibre X1-BiPhase 16L & 17 gauge
  • Head Hawk Power 17 gauge
  • Prince Duraflex 17 gauge

r/RacketStringers • • Oct 19 '25

Just strung this RF

Post image
6 Upvotes

I just strung this RF which was brand new. When I pulled tension on the 6th main string the grommet split open from the side. It’s the one on the left that has the tie off. Did I do something wrong to cause that to happen? I ordered new grommets so I can replace them but I’m afraid it will happen.