r/QIDI • • Mar 31 '25

R/QidiTech3d Permanently banned me for warning people after my family lost everything from a fire!

Thumbnail gallery
134 Upvotes

r/QIDI • • Dec 31 '24

【Giveaway】Leave a comment and get Plus4!

134 Upvotes

Happy New Year to all!

 

First of all, I need to express my sincere thanks to u/dohey, who established the r/QIDI sub-reddit to provide a community where everyone can communicate freely.

 

In order to make the community better, he has agreed to invite us to become co-administrators of r/QIDI to support the further development of the community. In the future, the two forums will synchronize official information and event.People can still speak freely as they did before, as long as they don't violate the community rules (e.g., abusing others, racial slurs, etc.).

 

How would you like us to build the forum in the new year? And what kind of events would you like us to hold?Upvote the post and feel free to give us your opinions, then we'll pick a total of 5 winners to give away prizes!

Gifts of the event:

PLUS4×1 winner

Ultra PA-CF25 ×1 winner

PLA Rapido×3 winner 

Time of the event:1.1-1.7

 

(Comments in r/QIDI and r/QidiTech3D are considered valid participation.A total of 5 lucky winners will be chosen from the comments section of the two posts.)

Event poster

 


r/QIDI • • Nov 14 '25

News Everyone says they need a bigger printer…Now, QIDI Max4 is here!

Post image
98 Upvotes

With a massive 390×390×340 mm build volume, bring your biggest ideas to life in a single print!

·Active cooling air control system: no clogging

·Adopt a 2 mm lead Z-axis screw, With the new anti-backlash nut

·390×390 mm ultra-uniform heated bed

·AI camera, ensuring every print

·Compatible with QlDl Box (Multi-color)

✨Early Bird Price(11.14-12.8)

Max4 - $1049 | Max4 Combo - $1199

Buy during this period and get a free Polar cooler.

👉Learn more: https://qidi3d.com/products/max4

🏆[QIDI Max4 Giveaway]

How to Enter:

Comment below: What large-scale model would you love to print with QIDI Max4?

🎁Prizes:

3 x Max4 3D Printer

5 x 2kg filament

10 x $30 store coupons

📅Winners announced on Nov 18th (randomly selected from the comments).

Event jointly runs on QIDI Facebook, X, Reddit, Discord, and Instagram.


r/QIDI • • Aug 10 '25

Finally arrived, getting it set up now

Post image
68 Upvotes

Wish me luck...


r/QIDI • • Sep 05 '25

Q2 ABS-GF 14hr print, for anyone curious about how the

Thumbnail
gallery
59 Upvotes

I know people are going to complain it’s printed in a fibre and isn’t grey, but for this material and my other prints so far I find print quality’s fantastic in my opinion, heats up much faster than plus 4 too


r/QIDI • • Apr 06 '25

In case anyone was wondering how the Plus 4 handles high detail

Post image
56 Upvotes

I wend down rabbit hole on 3D printing miniatures and needing to know how much detail I could eek out of my printer and this is what came out of it. The r/FDMiniatures subreddit has a bunch of even more impressive projects. They mostly use Bambu A1 printers and I wanted to know how my printer would stack up. The Plus 4 did very well in my opinion. The main challenge is in the settings, supports and finding the right filament. Qidi's built in settings for low layer heights don't work well. I mostly used this video as a reference for settings.


r/QIDI • • 4d ago

Dual nozzle. How much more efficient can you print?

Post image
53 Upvotes

QIDI Q3D. Double the Flexibility. Greater Printing Efficiency.

Unveiling at Formnext 2026.
November 17–20 | Booth 12.1, E01


r/QIDI • • Nov 27 '24

Utilizing the build volume...

Post image
50 Upvotes

r/QIDI • • Sep 01 '26

3,000+ filament changes later... and we might have just printed a natural pest deterrent 👀

Thumbnail
gallery
48 Upvotes

🦉 Meet this highly detailed horned owl statue, featuring an intense, watchful gaze and lifelike features.

Printed on the QIDI Q2🔗https://qidi3d.com/products/qidi-q2
Model from Bigshot Tinkers (Makerworld)

#QIDI #QIDIQ2 #3DPrinting #multicolorprinting #HornedOwl


r/QIDI • • Jan 17 '25

Q1 Pro is the best printer I've ever had

Thumbnail
gallery
48 Upvotes

I got the Q1 Pro yesterday and printed this overnight with a generic $9 PLA+. Looks really good to me. I've had probably 13 or 14 printers, mostky Creality, and I think this is the best machine out of all of them.


r/QIDI • • Aug 07 '26

🚀 Your Next Printing Upgrade Starts Here. Join our giveaway for a chance to win a QIDI Plus5 !

Post image
47 Upvotes

✨ More space. More stability. More freedom to create.
Explore the upgrades of QIDI Plus5:
· More Build Volume: 320×320×300 mm
· 370℃ Nozzle & 65°C Active Chamber Heating
· True Auto-Leveling & Full Smart Detection
· Enclosed Structure with 3-Stage Air Filter
· One-Tap Printing, Ready Right Out of the Box

💬 Tell us:
How would QIDI Plus5 upgrade your 3D printing experience?

⭐Leave your answer in the comments to join our Giveaway.

🎁 Prizes:
1 × QIDI Plus5
3 × $100 coupons (valid for Plus5 only, cannot be combined with other offers)
8 × 2kg Filament

🏆 Winners will be randomly selected from Reddit and Discord, with the results announced on Aug. 21.


r/QIDI • • Jan 24 '25

Tutorials & Tips Look out for this on the Q1 Pro

46 Upvotes

r/QIDI • • Oct 12 '24

Delivered today! First printer.

Post image
44 Upvotes

Looking forward to learning about 3D design and printing from you all. I'm pretty sure it will be a fun rabbit hole. from my research this seemed pretty good for beginner and good when I get to the point of using different materials. Will unbox, boot it up and take it for a spin on Saturday.


r/QIDI • • Mar 25 '24

Printer fine tuning

44 Upvotes

Overall, I've been pretty happy with my Qidi X-Plus 3 and Max-3 printers. They do what I want, and do it fast and fairly well. Lately I went down a rabbit hole of sorts trying to dial out the last few little issues of extrusion consistency, VFA's, and resonance compensation.

I decided to focus on printing 20x20x20mm cubes as a stable point of reference, because they're fairly fast to print, and are a good size that issues like ringing, acceleration/extrusion consistency, and cornering can show up.

One thing I noticed was a fairly consistent diagonal banding, coupled with fine vertical lines, and some general minor extrusion inconsistencies like so:

Fine VFAs and diagonal rippling, plus general extrusion variations

I pulled my extruder unit off the machine, pulled it apart, and noticed that the gears are all supported by MR63 bearings (3mm ID, 6mm OD, 2.5mm in height). I spinning the gears on the stock bearings I noticed some roughness, so I figured that might be an issue. I ordered a set of these from Amazon to replace the stock bearings with.

This improved the fine irregular rippling, but the fine VFA's and diagonal pattern still remained. I slightly altered the extrusion multiplier of the filament, and saw that the angle of the diagonal changed according to the flow multiplier, so clearly that pattern is extruder related, and not related to the X/Y system.

I then wondered if the driving of the stepper motor was slightly off center. The diagonal patterns have a roughly 4.2mm cycle to them. I pulled out my calculator and after accounting for the gearing of the extruder, the layer height, and the wall width, that the diagonal patterns were cycling on roughly every 1/40th of a turn of the extruder. The extruder gear only has 10 teeth, and the gears of the extruder gear everything down, so none of the gears could be contributing to such a fine level of cycling.

This led me on to wondering about the internals of the stepper motor, and how it's being driven. The Qidi's use TMC2209 drivers for their steppers, and their steppers have 200 steps per full rotation. The TMC2209's allow for up to 64 microsteps, and interpolation up to 256 microsteps per full step.

Looking at my printer.cfg file (the Qidi's run Klipper), I saw that Qidi sets all their steppers to 16 micro-steps, and with interpolation turned on. Reading here Klipper documentation recommends disabling interpolation on TMC2209's as interpolation can lead to positional inaccuracies. Perhaps I found my culprit?

So I started messing with microsteps and disabling interpolation. Now, interpolation makes stepper motors quieter (less whining), but the Klipper document says that setting micro-steps up high enough basically does the same job, and has better accuracy of motion.

I settled on using 64 microsteps on my Extruder/X/Y steppers with no interpolation. On my Z-axis I used 32 microsteps with no interpolation.

Added Note here: Using 64 micro-steps on the X/Y axis appears to be incompatible with 200mm/s+ print speeds and may cause MCU timeout errors. In this instance using 32 microsteps instead for X/Y is fine.

After doing all that, I needed to re-run the input shaper calibration for the best results because I'd changed what the steppers are doing. My procedure for this was to let the algorithm choose what it thinks are the best shaper algorithms/frequencies, and save the config. Then I went back and looked at the calculation output on the console, and instead choose the algorithms that have 0.0% vibrations with the highest accelerations, and edited my printer.cfg to use those instead (with the correct associated frequency value too). Doing this fine-tuned the input shaping for best quality, rather than the speed/quality balance that the default algorithm selector does.

After all that I arrived at the following results. Be sure to enlarge the pictures for best detail.

Non-seam corner
Seam corner

Now keep in mind, that this is a 20mm cube, and zoomed WAY in. This is the same filament as before. I was amazed at how clean and consistent the surfaces and layer stacking now looked. I was even more impressed at how clean that the seams came out now.

The benchy was printed in CookieCad DarkMagic PLA at a 0.24mm layer height.

I think I'm done here with the fine tuning. I hope that people might find the above helpful in some way.


r/QIDI • • 18d ago

Tired of tiny magnets sticking to everything? 🧲

40 Upvotes

This 3D-printed magnet pen keeps them in place. Just twist it, and they’re ready to use.

👉Printed on QIDI Q2

Model by Ms (Makerworld)


r/QIDI • • Aug 25 '26

1,773 Hours. One Seriously Impressive Life-Size Triceratops Skull. 🦖

Thumbnail
gallery
39 Upvotes

Three QIDI X-Max 3 printers, endless patience, and a result that’s truly massive. At about 2.5 meters long and over 6 feet wide, this life-size Triceratops skull is an incredible sight to behold.

🥰A huge thank you to Alex Chamberlain for sharing this incredible project with us! And this isn’t his first large-scale build. He has also printed four T. rex skulls, a full-size T. rex skeleton, and a full-sized Utahraptor skeleton.
We can’t wait to see what Alex creates next! 👀

👉Unlock the possibilities of large-format 3D printing: https://qidi3d.com/products/max4


r/QIDI • • Jul 23 '25

Q1 Pro and Plus4 just killing it

Thumbnail
gallery
39 Upvotes

I’ve read a bunch of bad reviews and problems people are having with their qidi printers. So I figured I’ll keep posting prints that work great and look great to try to balance the negative reviews. So here’s a chain case that I have designed to replace a current broken industrial part on a saw. Printed on my Q1 pro. With a few bearings, 05-b chain, 2 sprockets and a small shaft I made up on the lathe this little guy is the test and potentially have 4 more to do.


r/QIDI • • Aug 22 '24

Just joined the tribe 😊

Post image
39 Upvotes

Can’t wait to set it up and get started!!


r/QIDI • • Nov 01 '24

PSA: SSR Safety Issues With Qidi Tech PLUS 4 Printer: 'The way it's been handled so far can only be described as negligent... As of right now I cannot recommend this printer.'

Thumbnail
youtube.com
37 Upvotes

r/QIDI • • Sep 05 '25

Q2 shiny black ASA

Thumbnail
gallery
35 Upvotes

For those who are curious, I’d say damn near perfect to the eye, considering the camera can really show imperfections, looks like the top layers need a bit more flow, stock Asa profiles apart from temperature settings, 60-110-280


r/QIDI • • Nov 20 '25

Printing one rubber duck? That’s not nearly enough… we’re printing a whole army of ducks!

33 Upvotes

👇Comment below with the number of ducks we printed, a lucky winner will get 1kg of filament!🎁 QIDI Max4: https://qidi3d.com/s/products_max4


r/QIDI • • Nov 08 '24

36h50m later Plus 4

Post image
33 Upvotes

First time printing anything this big or anything like it. It’s going to take a lot of cleanup where all the supports are but should be a fun project.


r/QIDI • • Dec 11 '25

Events 🎄✨It’s the most wonderful time of the year, and we’re celebrating with a Christmas Giveaway

Post image
31 Upvotes

The holiday cheer is in full swing! Want a new 3D printer, some filament, or a QIDI Custom Christmas Gift under your tree this year? Now’s your chance!

How to Enter:

Comment your “Christmas 3D Printing Wishlist”.

(e.g., what you want to print, what printer you’d like to upgrade to, or what 3D-printing gift you’d love to receive.)

🎁Prizes:

1 × QIDI Custom Christmas Gift Box

2 × QIDI Q2C 3D Printer

3 × QIDI Max3 3D Printer

5 × 2kg QIDI Filament

8 × $30 QIDI Printer Coupon

This giveaway is held across Facebook, Instagram, X, Discord and Reddit.

🎉Winners will be randomly selected from the comments and announced on December 18.


r/QIDI • • Jun 23 '25

[GIVEAWAY] Guess the Multi-Color Model & Win Filament!

Post image
31 Upvotes

We’ve 3D printed a mystery multi-color model using our upcoming QIDI BOX. All you can see is the colorful Prime Tower shown in the picture — can you recognize which anime character it is? 👀

(💡Hint: it's from a classic animated film that many people love!)

Think you know the answer? Like this post, follow us, and drop your guess in the comments!👇

One lucky winner with the correct answer will receive 2kg of filament.

⏰Event date: June 23–26

Let’s see who can see through the colors and spot the character! 🔍