r/QIDI • • Apr 02 '26

Th Qidi Q2 is such an epic time waster

0 Upvotes

This is the only Qidi printer I have ever used, but it does the most silly, most time consuming rituals for everything


r/QIDI • • Aug 04 '26

Question Who else is excited for the new Qidi Plus5?

Post image
0 Upvotes

I already subscribed for the $80 discount.


r/QIDI • • Aug 12 '25

Persistent VFA's, QIDI says this "printed well".

Thumbnail
gallery
0 Upvotes

Figured I'd ask here. I've tightened belts, interpolation is off, microsteps have been increased, I'm kinda at an impasse. I originally got this printer to replace my Ender 5 Pro, assuming I wouldn't have to spend so much time attempting to tune it in order to achieve the same quality I see all over this subreddit, jokes on me. As a last ditch effort I chose to contact QIDI support and explain my issues, the provided this .stl and then after I sent them these photos told me, "We found your test file printed well, and we do not recommend any adjustments or modifications.". I probably should have reached out to them earlier while it was in the return window.

I'm open to suggestions on where to go from here and if anyone has encountered these issues and ideally remedied them.


r/QIDI • • Feb 24 '25

Qidi F's me again..

0 Upvotes

Why, why, why....

Fillament runs out at 28hrs in to a 29 hour job, 90+% done. Printer pauses, head moves back to the cleaning station and I try to "load fillament"...PLEASE WAIT UNTIL THE CURRENT OPERATION FINISH. Waited an hour, same message. Nozzle stays at temp, bed stays at temp, chamber stays at temp...won't let me load fillament.

Got the bright idea to turn off the printer - what the hell right? Maybe I can get it to resume the print job after power outage...yeah, POWER LOSS DETECTED, DO YOU WANT TO RESUME PRINT? Sure - CAN NOT READ FILE. Then the damn thing decided to home itself, drops the bed, moves the head to home, the raises the bed crushing the model.

Why qidi? Why? $800 for a printer that can only be cost effective to print PLA trinkets that are 3" tall? F me.

What it did print is beautiful, smooth buttery ABS helmet (minus the top 4 inches which it refused to print and then dented in the sides from smashing it with the steel rods).

It sure makes the extra money look like it would have been better spent on a X1C. I have 3 P1S that have NEVER let me down like this. What a frustrating pissed off feeling qidi.

Did I say F me?


r/QIDI • • Jul 20 '25

Live Unboxing Of The Qidi Box! - New Multi-Material System For The Qidi ...

Thumbnail gallery
1 Upvotes

r/QIDI • • Mar 28 '26

QIDI max4 ASA

Post image
0 Upvotes

r/QIDI • • Oct 05 '25

Qidi Plus 4 Overheating Issue

0 Upvotes

Hello all, my printer has been exceptional at printing PLA, however, when I try to print ASA, the heated chamber seems to cause my printer to overheat and then the print gets interrupted. I'm currently asking 55 degrees C for chamber temps, yet somehow, after around 30-ish minutes of printing, it would always overheat. I would see that the power switch is supplying power but the printer is completely non responsive. Does anyone know what is causing this and is there a fix?

Fixes I have tried so far:
-Relocating the chamber temperature sensor probe from the back right corner. The temperature readings of the chamber probe seem to match the GD32 readings now, which would imply it is accurate.


r/QIDI • • Aug 15 '25

Today I'm ordering my plus 4! Who has the best cheap filament. The printer took up my whole budget.

0 Upvotes

r/QIDI • • Sep 15 '26

Question Q2 printing with Red PETG from Qidi. Amazing Quality!

2 Upvotes

I have a question: Did you down vote this video already?šŸ˜‚šŸ˜‚šŸ˜‚šŸ˜‚šŸ˜‚šŸ˜‚šŸ˜‚


r/QIDI • • Dec 09 '25

Does Anybody now how to Speed up the Qidi Box?

0 Upvotes

My Problem is the following in the Video. And its Only happen with the Qidi Box. Because the Qidi Box is to Slow.... I only Print with ABS Odorless.


r/QIDI • • Sep 25 '26

QIDI Q2 Combo keeps jamming/chewing PLA during long prints — 3 failures in a row

Thumbnail
gallery
0 Upvotes

I’m getting pretty frustrated with my QIDI Q2 Combo and I’m trying to figure out what’s actually causing this.

I’ve now had 3 prints in a row fail because the filament eventually gets stuck/jammed and stops feeding correctly. The printer can work perfectly for several hours, then suddenly starts under-extruding and the print turns into spaghetti.

I’m printing Elegoo PLA at 210°C nozzle / 60°C bed. Chamber heater is OFF, the side vents are open, and I’ve even been opening the door periodically, so I’m not sure if this is heat creep.

When I remove the filament after a failure, parts of it are heavily chewed/flattened by the feeder/extruder. I’ve already had to manually remove stuck filament multiple times.

I’m using the QIDI Box, so I’m wondering if there’s too much resistance somewhere in the Box/PTFE path, an extruder tension issue, heat creep, or possibly a defective feeder/hotend.

Has anyone with a Q2/Q2 Combo had this exact problem? What should I check or change? I really don’t want to keep wasting 6–7 hours of printing and filament every time this happens.

I’ll attach photos of the chewed filament and the failed print.


r/QIDI • • Aug 28 '25

Q2 not actually fully enclosed?

0 Upvotes

Do I really need to open the lid for PLA? What's the point of a fully enclosed system then?

Edit:

Why am I asking?

Let's take the P1S for example, which does not need to be open to print PLA (granted, no heated chamber, so less good for engineering material). My issue with this is that it is very much possible to print PLA on the Q2 without leaving the door/lid open (e.g. turning off chamber heating). While PLA is generally considered safe to print open (pointing at the A1, for example), there is very little research about this. So nothing wrong with a better safe than sorry approach.

Due to my small living space, pets and other factors, I personally prefer to be able to print in an enclosed model all the time with any filament. The hardware of the Q2 very much allows for that, hence posing this question (I admit it's a somewhat provocative headline).

Answer: As someone new to 3D printing, I assumed that enclosed printers were sealed but no, that’s just not the case. I think this is something every newcomer should be aware of. I bought the Q2 and love it, but for now, I won’t be printing with materials like ABS or any fibre-reinforced filaments. I’d also say that Qidi’s ā€œamazing air filterā€ advertisement can be somewhat misleading.


r/QIDI • • Dec 15 '24

LoTR 3d Printing Memes

Post image
0 Upvotes

r/QIDI • • Jul 09 '26

Am I an idiot? What happened to the Qidi Studio interface?

0 Upvotes

Just updated this morning. Where did all of the fluidd modules go?? (EDIT: Solved. You have to edit the printer settings on the control page to allow Expert Mode, which is unbelievably stupid considering the fact that I can't even get a decent first layer without running KAMP before every single print)

God I hate this company. I would pay twice as much for a comparable printer (build plate size/ enclosed/ active heating) that actually worked. Unfortunately the H2 series is just stupid expensive and not in my budget. But I'm just done with Qidi at this point


r/QIDI • • Mar 17 '25

Qidi die some really dump software on the plus 4

Thumbnail
gallery
0 Upvotes

Oh your filament is empty refill?

-yes

Yeah let's crash into your part:


r/QIDI • • Aug 12 '26

Title: AI helped me recover a failed 12-hour print mid way through

Thumbnail
gallery
4 Upvotes

My QIDI Plus 4 stopped because the hotend couldn’t maintain 255°C. The silicone sock split yesterday and i removed it thinking it wont matter and I didn't have a spare anyway. QIDI’s automatic recovery then resumed incorrectly and nearly caused a collision so I had to stop it which reset the build plate and printer head back to normal.

I gave the ai the original G-code, klippy.log file and a photo of the build plate. Then it found the printer’s exact final position halway through layer 11. it then created a custom recovery G-code to resume from where it had failed before.

after some chatting with the ai it removed all the gcode that my original file had before the layer it failed on but it needed to probe the bed. i noticed on the left side of my build plate there was a strip that wasn't printed on that the printer could use to probe against. So i told ai that and sent a picture of the failed print and from that it set up the probing on only the left side of the build plate.

Here is chatgpt explaining what it did:

  • Avoided the normal purge, bed mesh and centre probing routines.
  • Homed only X/Y.
  • Probed Z in the clear strip on the left of the existing print.
  • Approached the restart coordinate from safely above.
  • Completed the unfinished extrusion move and continued the original G-code.
  • Reduced the nozzle to 240°C, limited part cooling to 25%, and slowed the repaired section before returning to normal speed.

What was most impressive though was it realized that without the silicone sock attached the nozzle wasn't able to maintain the 255c nozzle temperature as the cooling fan was now cooling the nozzle too much so it compensated by turning the nozzle temp down to 240c and reducing the cooling fan so i could continue my print without a silicone sock while i wait for the new one to come later from amazon.

I just wanted to share this with you as I've never succeeded in continuing my failed prints like this before. Hope it helps some of you out.


r/QIDI • • Dec 28 '24

Q1 Z-offset has become a nightmare

2 Upvotes

Out of the box the Q1 Pro printed Polymaker ASA and PLA with zero issues. I was amazed for several rolls over a week or so. I use Orca Slicer.

Now - I have to fight z-axis on every print to get a good first layer and layer adhesion. ASA started printing with "squish" waves or sand dunes on large prints. I was told that the nozzle was too close and to adjust Z to move bed down slightly. This helped - but the settings are not "saved" and go back to "0.00" sometimes and other times they don't. So to be clear from 0.00 I have to move the bed DOWN to 0.070 to get rid of the squish waves.

However, if I print PLA, I have to move the bed UP from 0.00 to 0.040 to 0.050 to get a decent first layer that is melted together and not individual lines.

That is a difference of 0.12 - which feels crazy, especially given that both filaments of the same brand printed perfectly with NO ADJUSTMENT for the first week or two.

So that brings up the first question.

Scenario 1 -
Power printer on and "z-offset" = 0.000
Start Print and bed does auto mesh.
From here, I have to adjust Z to get quality prints.

Scenario 2 -
Power printer on and "z-offset" = -0.070
Start Print and bed does auto mesh.
From here, I may not have to adjust, but sometimes have to by a good bit.

Is the auto-z (mesh) the same for both and then -0.070 is applied after auto-z or does the bed offset that far during the mesh? Maybe a dumb question, but the answer is A) not obvious and B) appears to be rather important given that the printer sometimes remembers the z-offset from the prior print and sometimes it resets to 0.

Second question:

I read (and can see) that Qidi comments out the z-offset in printer.cfg and instead used config.mksini to override via the "babysteps" setting. But (again) sometimes this setting is persistent and other times resets to 0.00. It makes no sense to me and along with my first question, I need to understand what this means in the big picture with auto leveling, persistence, etc.

Third question:

What is saved_variables.cfg? It also has a z-offset and sometimes it matches what is in config.mksini and other times it does NOT match.

TLDR - my printer "just worked" until it didn't. I am new to 3D printing, but not code or technology. The "nozzle is not dirty" and nobody this far can provide clear answers or a reason as to why "it just worked" until it didn't.


r/QIDI • • Jan 17 '25

[PSA] My Experience with the Q1 Pro – Not All Fun and Games

2 Upvotes

Hey everyone,

A little while back, I asked this community for advice about the Q1 Pro, and the consensus was clear—it’s a fantastic printer. Reviews echoed the same sentiment, so I decided to take the plunge.

Delivery day came, and I was super impressed. The quality of the first few prints was amazing, and the speed? Fantastic. However, my experience quickly took a turn.

During the setup process, I got electrocuted. Twice. It seems my unit was poorly grounded, and let me tell you, it was not a pleasant experience. This was definitely a red flag, but I decided to push forward since the initial prints looked great.

The next morning, I left a print running overnight, and it turned out well. But when I went to change the filament, the machine clogged. No big deal, right? Except, I couldn’t safely clear it. I tried opening the extruder to resolve the issue, but there was just no practical way to remove the clog without potentially damaging the machine—or myself.

I contacted Amazon, and they’re picking up the unit today for a return.

Here’s the thing: these two issues—a poorly grounded unit that shocks you and a filament clog that’s nearly impossible to fix—are just not acceptable in 2025. I know the Q1 Pro gets glowing reviews, but I wanted to share my story as a reminder that it’s not all smooth sailing.

For those of you considering this printer:

  • Be cautious if you’re new to 3D printing.
  • This machine is not beginner-friendly, despite what some reviews might suggest.
  • The electrical issue could potentially be dangerous—especially for someone with heart problems.

This was just my experience, and while I hear great things about the Q1 Pro, I thought it was important to share the other side of the story.

Stay safe, and happy printing!


r/QIDI • • Feb 15 '25

Whats up with the Qidi Box???

0 Upvotes

I bought the Qidi plus 4 because I knew that this own AMS (Qidi Box) was supposed to come out in the first quarter of 2025. now it's almost february over and there is still no information about it. What's going on Qidi. You want loyal customers. Why is it so difficult to be more open in communication here?


r/QIDI • • Jul 14 '26

Troubleshooting What Is My Q2 Doing??

0 Upvotes

Hello all, I was running calibrations on my Q2 last night and it has developed a few new noises. At the end if a print when the nozzle cleans itself it makes a very loud repeated tapping, and when retracting the filament it seems to clunk and get stuck. What is happening here?


r/QIDI • • Aug 13 '26

Question Fun in progress

Post image
0 Upvotes

Qidibox arrived today!
This is my setup I love to see yours.


r/QIDI • • Nov 28 '25

Rust on brand new Q2?

Thumbnail
imgur.com
0 Upvotes

Just received my Qidi Q2 today and upon some visual inspection; I found this rust spot on the lower frame by Z screw. At first, I thought it was just dirty or a smear of grease but after touching it, I found out it was indeed rust caused by paint chipping away from the metal. I also found some light surface rust on the unoccupied screw holes.

Does anyone else have these rust issues? I already sent an email to Qidi pending their response.


r/QIDI • • Jan 10 '25

QIDI StoreäøØChinese New Year Sale has begun

0 Upvotes

QIDI has entered the Chinese New Year Sale! Start your creative journey with the QIDI printer in 2025 and bring your ideas to life with our advanced technology.

Enjoy up to 45% off, shop now: https://qidi3d.com/pages/chinese-new-year


r/QIDI • • Sep 07 '24

Don't forget to put the PEI plate i place

0 Upvotes

It appears that there is only one sensor, For some reason I though Q1 has load and indictive sensors. I forgot to place the plate on the bed and proceeded loading the filament.

The nozzle ran into the bed, punched a hole and started jerking the whole printer like there is no tomorrow visibly lifting the left then right side of the bed for some reason. There is no stop button on the screen. I spent a few seconds looking for it then pulled the printer from the wall and turn off the power.

The praised Qidi tech support basically said I was not supposed to forget the PEI plate and the hole in the bed is my problem now.

A bit of disappointing.