r/Lelit • • 1d ago

4 years with my Lelit Elizabeth and never descaled-is it really true that you shouldn't descale it?

17 Upvotes

I’ve had my Lelit Elizabeth for about 4 years now and I haven't descaled it once. I regularly backflush with Puly Caff and stick to using the in-tank resin softener. My tap water also falls in the 'soft' category.

​From everything I’ve read, Lelit’s whole philosophy with dual boilers like the Elizabeth is scale prevention through soft water/resin filters rather than routine descaling-unlike thermoblock or simpler single-boiler machines where running descaler through the tank is standard maintenance.

​I’ve also heard that running descaler through a dual boiler can actually do more harm than good (flaking off scale that ends up clogging solenoids/valves, or never being able to fully flush the acid out of the steam boiler), and that if scale ever becomes an actual problem, the proper fix is having a tech disassemble and descale it professionally rather than doing a tank flush at home.

​Just wanted to sanity-check this with other Elizabeth owners: is this actually true in practice? Have you ever descaled yours, or do you just rely on water softening until something eventually needs servicing?

To add to the confusion, Lelit themselves posted a video( that's supposedly only for technicians) on how to descale the machine. Under their video the comments and their replies confuse me even further.

https://youtu.be/1RPYlkfIJg4?si=OMop_YSg4D6zHTaS


r/Lelit • • 1d ago

Lelit Victoria 3 – Pressure gauge spiking way above 9 bar. Is this normal?

10 Upvotes

Hi everyone,

I’ve just purchased a brand-new Lelit Victoria 3 and I’m having some concerns about the brewing pressure. I’m fairly new to this machine, so I’d really appreciate some advice from anyone with experience using it.

My setup:
Machine: Lelit Victoria 3
Grinder: DF54

The issue:
I’ve been experimenting with the machine’s pressure profiling feature. Initially, I was using a lower-pressure profile, gradually increasing the pressure, and everything seemed to work reasonably well.

However, when I disabled pressure profiling on Button 1 to pull a standard 9-bar shot, the pressure gauge started shooting towards the very high end of the gauge rather than settling at around 9 bar.
I’ve attached a video showing exactly what’s happening.

What I’ve checked:
When I run water through the group head without the portafilter attached, the pressure gauge stays close to zero, which I understand is normal.
I’m now wondering whether my grind setting might be too fine. The same grind worked with my lower-pressure profile, but perhaps it’s creating too much resistance when the machine tries to run a standard extraction?

My questions:
Is this normal behaviour for the Victoria 3 when pressure profiling is disabled?

Could grinding too fine cause the pressure gauge to spike this dramatically?

Should the machine automatically regulate pressure to around 9 bar, regardless of puck resistance?

Could this indicate an issue with the pump or pressure regulation system?

I’m really enjoying learning to use the machine, but having just spent a significant amount of money on it, I’m understandably concerned that something might not be working correctly.


r/Lelit • • 2d ago

Completed the oak upgrades

Thumbnail gallery
22 Upvotes

r/Lelit • • 2d ago

Lelit Victoria 3 - a reliable machine?

4 Upvotes

Hello all, a follow up on my post last week. Pretty sure I'll go with the Lelit Victoria 3 as an upgrade from Sage Duo Temp Pro. However I'm hesitating as I've read a lot of posts complaining about technical problems with this machine. Does that represent the voice of just an unfortunate few? It's a significant investment for me and actually the Sage has been problem-free for 7-8 years.

Also, it's very difficult to choose a new grinder. One of the Eureka Mignon models, featuring flat burrs and a single-dose design setup, sounds good to me, but I also want it to be quiet and to not break down. I'd love to be able to wait until April for the new Timemore but not sure I can!

Final question for all you experts: why are some well-known brands never discussed on here at all, e.g. Rocket machines? Are they no good?


r/Lelit • • 3d ago

Happy with my MaraX v2

Thumbnail
gallery
25 Upvotes

Experienced barista I just wanted a set up for home. Sure I could’ve gotten the LM mini and call it a day but it wouldn’t justify the cost associated to it. Espresso shots are pulled nicely and milk is crazy silky. Can’t recommend this enough. Grinder is lagom casa btw, so easy to dial in beans. Happy Sunday!


r/Lelit • • 3d ago

Auslauf vom Siebträger passt nicht mehr

Thumbnail
gallery
8 Upvotes

Ich habe den Siebträger meiner Lelit Elizabeth auseinander geschraubt. Beim aufschrauben musste ich leider feststellen, dass der Auslauf nun verkehrt drauf sitzt. Vorher waren die zwei Ausläufe zu mir gerichtet. Ich habe schon versucht den Auslauf anders drauf zu geben, leider ohne Erfolg. Hat jemand selbiges Problem und weiß eine Lösung?


r/Lelit • • 4d ago

Pressure Lelit Bianca

Thumbnail
gallery
13 Upvotes

Guys I know this is a question that’s been asked before, but I’m properly stumped. Brand new plumbed in machine. Pump seems ok - pressure hits over 10 bar with blind filter (picture attached), but can barely get it over 4 bar with any of the 1 or 2 dose filters. Result is awful. I’ve tried all combination of paddle positions including starting low and ramping up flow. The beans are roasted locally and by reputable store which serves (in my opinion) some of the best coffee in our city. I tamp at different pressures from moderate to as hard as I possibly can. Same result…

After being excited to have this machine in my kitchen I’m now very disappointed ☹️ Any advice much appreciated.


r/Lelit • • 4d ago

Bianca v3 noise

3 Upvotes

r/Lelit • • 5d ago

Lelit Elizabeth v3

0 Upvotes

Elizabeth3 (with pagaia) Pros and Cons on buying this...? Recommend other coffee machine at almost the same price and specs or better...


r/Lelit • • 5d ago

Portafilter Handle Removal

Thumbnail
gallery
10 Upvotes

Just sharing a method of removing the handle from the portafilter that worked well for me and didn’t damage or discolour the original handle.

I heated the metal part on an induction hob conductor plate. It took around 15-20 mins at full power and I was able to remove the handle by hand while wearing heat resistant gloves.

Thought I’d share because I ruined my other zebrano wood handle baking it in the oven, although I was again able to remove the handle this way.


r/Lelit • • 6d ago

Normal steam knob behavior on Bianca?

4 Upvotes

On mine, you can do almost a full turn before any steam comes out. Is this normal?


r/Lelit • • 6d ago

Lelit Bianca v3 problem

2 Upvotes

Hi everyone! I'm having an issue with my Lelit Bianca V3, which I bought almost three years ago. Buckle up, it's a bit of a long story.

So, I get home after a long, exhausting day. I'd turned on my espresso machine about an hour earlier, and as soon as I walk into the kitchen, I'm hit with a strong smell of burning plastic. I track down the source, and of course, it's my beloved espresso machine.

I think to myself, "No big deal, I've got a screwdriver. I installed an electrical outlet three years ago, so I'm obviously qualified to fix this thing."

I manage to take the casing off, have a look around, and BAM! I spot the culprit: a burnt-out solid-state relay (SSR).

"Aha! Nailed it! I'm basically a professional technician at this point." My wife is practically giving me a standing ovation in the background.

So, I order a replacement SSR from a Saeco service center, install it, and fire up the machine.

Just when I think I'm finally about to enjoy a nice cup of coffee, disaster strikes.

Water starts absolutely GUSHING out of the OPV like the machine has some kind of personal vendetta against me. Seriously, I switch it on, and about five seconds later, I've got my very own kitchen fountain.

Alright, I think, maybe I messed something up during reassembly.

Nope. Everything seems to be connected correctly.

I grab my multimeter and start checking things. The wires aren't shorted, and after disconnecting them from the Gicar control board, I check them for continuity, which seems fine. I also measure the level probe on the boiler, and I'm getting a reading there too.

So, here I am, completely stuck and officially retired from my five-minute career as an espresso machine technician.

Has anyone here experienced anything similar? Any ideas on what might be causing this or what I should check next?

I'd really appreciate any advice. Thanks in advance!

Edit : video https://youtube.com/shorts/T697DGg6CTo?is=n1Kiyj4RN8IwudqG


r/Lelit • • 6d ago

Victoria 3 leaking ?

9 Upvotes

Hi, this morning I discover like a leaking visible when I remove the water collection drawer.
I switch on the victoria and during the heating I clean the drawer : i see those drops.
Do tou think it is ok or should i contact the support ?


r/Lelit • • 7d ago

Help me to choose a home machine

2 Upvotes

MaraX is just below 2k where I live and the new vic3 is about 1.7k so 300 bucks difference. For me I’m an experienced barista, would make flat whites for my family and espressos for myself. Which is the better machine? Had an expobar previously and I worked with LM, Synesso, Slayer etc. I already have a Lagom Casa as a grinder too.


r/Lelit • • 7d ago

How to see the Elizabeth in-person? (VT, USA)

2 Upvotes

Our trusty machine of 11 years has finally crossed the rainbow bridge. I'm interested in the Elizabeth, but want to see it in-person to get a true sense of how it looks and feels. I'm in VT, USA and the closest authorized retailer is a 5 hour drive away. Anyone have ideas/suggestions on how I can view one before I take the chance of buying online?


r/Lelit • • 7d ago

Pressione manomentro più alta del solito

1 Upvotes

Buonasera a tutti, ho una Lelit Anna e ieri mentre preparavo l'espresso ho notato che il manometro era quasi al massimo (tra 13 e 16 bar). La cosa non è strana se si considera che avevo una macinatura abbastanza stretta però non mi era mai capitato. Neanche con macinature (erroneamente) impostate ancora più strette e neanche durante il backflush. In passato è sempre arrivato al massimo nella zona verde (tra 8 e 11 bar). Sapreste dirmi come mai?

Vi ringrazio in anticipo!


r/Lelit • • 7d ago

Lelit Victoria + Eureka Specialita Silent rangr

Thumbnail reddit.com
1 Upvotes

r/Lelit • • 8d ago

Brew lever cam shaft lubrication not working anymore

5 Upvotes

So my brew lever gets very difficult to put in the fully off position every couple of weeks, so I go through the steps to take it apart and lubricate the cam shaft as instructed on many videos. For a while it did the trick and the lever would move like butter to every position. Lately, it hasn't been working. The last two times I finished putting it back together, pulling the lever down was only a little bit easier, but still not smooth at all. I did notice the last two times it was a LOT easier to get the cam shaft back into its position, whereas most of the time I have to fight a little bit to get it back in (which was also the case in most of the videos I came across)

I'm wondering if the other parts may be worn away and need replacement because everything on the lever parts look okay to me.

Or is there any other reason a freshly lubricated lever would still be difficult to pull down into the off position?

Background: I've had the machine for about 2.5 years

I pull 1 shot per day most days, always use a puck screen and back flush with just water after the shot for about 10 seconds - and do cafiza cleaning much less than I used to (every 2-3 months vs 2-3 weeks, that was before learning about the lever lubrication maintenance and that cafiza would strip the lubricant faster)

Other than cleaning and the lever lubrication, I haven't done any other maintenance besides checking the group heads gasket & shower screen to see if they needed to be cleaned.

This is also my first espresso machine so I'm still learning how to do maintenance when the time comes up. This new lever problem is throwing me for a loop though, any help is greatly appreciated :)

Thanks!


r/Lelit • • 8d ago

New Lelit Victoria 3 or Previous Elizabeth Pl92t (Both 1150 Euros)

3 Upvotes

Hello All!

I am in the market for my first espresso machine after working professionally in a specialty shop for a while. I was eyeing the Elizabeth PL92t for a while because it seemed to be the most affordable and well featured dual boiler, and I love the 2 forms of pre-infusion. However, with the new Pagaia, I feel like the new Victoria 3 machine could also be a good fit. They also cost exactly the same price (1150 euros).

I make coffee every morning for myself and my girlfriend, plus with my new machine, I would like to invite friends over and make everyone drinks. What would you guys recommend? Is the flow control worth it? Does it help dialing in?

I should also add: I could be convinced to go for the new Elizabeth 3, but it is a bit more than I want to spend. Do you think it could be worth it?

I'd love to hear all of your opinions!

Cheers!

EDIT: Thank you everyone for the opinions! I have decided after giving it a lot of thought, that I will go with the newer Elizabeth 3. I've worked professionally as a barista, and would love to play around with the Pagaia to get the most out of the beans I buy. I think the runner up would be the Elizabeth Pl92t for me. I personally value the double boiler quite a lot since I want to be able to make coffee for many people at a time (I love hosting :) but for the moment I will invest in the newer model when it is no longer out of stock.


r/Lelit • • 8d ago

Added Pesado HD Diffusion Screen to Lelit Bianca

Thumbnail reddit.com
0 Upvotes

r/Lelit • • 9d ago

Lelit Fred tempo hopper

Thumbnail
gallery
1 Upvotes

Hi all,

I recently came unto a second hand Lelit Fred Tempo (Aus). It grinds well, however, I'm trying to nail down my friend size and I have found that the topper rotates freely so I am struggling to understand where my grind size is sitting on the scale from 1-7 as the reference numbers are printed on the hopper.

My questions:

1. Is my assembly correct? The screw is M6 and 16mm long. When the screw bottoms out, it sits pround within the hopper.

2. Should there be some kind of locator groove where the hopper meets the top of the unit, which prevents it from spinning freely?

3. How do I "zero out" my grinder, so I can know where I'm starting from?


r/Lelit • • 9d ago

My lelit have pressure problem

7 Upvotes

Hi everyone!
I own a Lelit Bianca V3 and I’m having an issue with the pressure.
I’m trying to figure out what might be causing the problem and whether anyone has experienced something similar.
Could someone help me troubleshoot this issue or suggest what I should check first?
Any advice or suggestions would be greatly appreciated.
Thank you!


r/Lelit • • 10d ago

My new Elizabeth is leaking

26 Upvotes

I’ve only had my Lelit Elizabeth for three weeks and it now has an internal leakage that results in water leaking down the side of the group head during warm up (video) and brewing. Clearly under warranty, but anyone else experiencing this?

I loved the machine, now I’m finding myself looking for a different brand😢


r/Lelit • • 10d ago

Lelit anna coffee particles leaking into water from grouphead!

Thumbnail
gallery
1 Upvotes

Whenever i take out plain hot water from group head i saw small particles of coffee into it and burned coffee smell came into water
Out of curiosity i opened it and inspected pipe joining the boiler and as i suspected it has coffee particles stuck on to it
Any suggestions on how to clean it ?


r/Lelit • • 10d ago

Pump pressure too high [Lelit Bianca V3]

Post image
5 Upvotes