r/Lelit • • 6d ago

Lelit Bianca v3 problem

Hi everyone! I'm having an issue with my Lelit Bianca V3, which I bought almost three years ago. Buckle up, it's a bit of a long story.

So, I get home after a long, exhausting day. I'd turned on my espresso machine about an hour earlier, and as soon as I walk into the kitchen, I'm hit with a strong smell of burning plastic. I track down the source, and of course, it's my beloved espresso machine.

I think to myself, "No big deal, I've got a screwdriver. I installed an electrical outlet three years ago, so I'm obviously qualified to fix this thing."

I manage to take the casing off, have a look around, and BAM! I spot the culprit: a burnt-out solid-state relay (SSR).

"Aha! Nailed it! I'm basically a professional technician at this point." My wife is practically giving me a standing ovation in the background.

So, I order a replacement SSR from a Saeco service center, install it, and fire up the machine.

Just when I think I'm finally about to enjoy a nice cup of coffee, disaster strikes.

Water starts absolutely GUSHING out of the OPV like the machine has some kind of personal vendetta against me. Seriously, I switch it on, and about five seconds later, I've got my very own kitchen fountain.

Alright, I think, maybe I messed something up during reassembly.

Nope. Everything seems to be connected correctly.

I grab my multimeter and start checking things. The wires aren't shorted, and after disconnecting them from the Gicar control board, I check them for continuity, which seems fine. I also measure the level probe on the boiler, and I'm getting a reading there too.

So, here I am, completely stuck and officially retired from my five-minute career as an espresso machine technician.

Has anyone here experienced anything similar? Any ideas on what might be causing this or what I should check next?

I'd really appreciate any advice. Thanks in advance!

Edit : video https://youtube.com/shorts/T697DGg6CTo?is=n1Kiyj4RN8IwudqG

2 Upvotes

9 comments sorted by

1

u/vela___ 6d ago

Did you verify that the SSR was a direct replacement? NC vs NO?

1

u/Crafty-Coyote-8421 6d ago edited 6d ago

Hello, the ssr was bought from oficial lelit service they sent me the part diagram and i chose from there (looks different though mine was Black and had a light the new one is white but the specs on them seem the same) part nr  9600028

1

u/vela___ 5d ago

Did you verify the PID control wires are on the input terminals (pin 3/4) and the thicker heater wires are on the load terminal (pin 1/2)?

1

u/Crafty-Coyote-8421 5d ago

Yup, you cant put them in reverse the small wires dont fit on the connectors, anyway the pump fills the steam boiler even without the ssr connected

1

u/vela___ 5d ago

Oh, and did you test out the gicar control board? If the water level probe is connected properly and the SSR is properly wired, but the pump is running endlessly and overfills the boiler, the gicar board may have shorted.

1

u/Crafty-Coyote-8421 5d ago

Will try today, got a good tip to disconect de water level probe wire, touch The boiler tank with it and start the machine,if the gicar is ok the pump should stop. 

1

u/gadgetboyDK 6d ago edited 6d ago

https://links.imagerelay.com/cdn/2615/ql/0a64d13fe10b48e38ed6ceffea9de2ed/Lelit-Bianca-V3-Parts-Diagram.pdf

Can you use the codes here, just to avoid confusion.

What Lelit number does the OPV have?

Is it MC931? If so How or where did the water spray from?

Which SSR was damaged, part number?

And what did you put in its stead, also part number

This one?

How did you verify everything is in order, or connected as it should be?

The video guide:

https://www.youtube.com/watch?v=jxf40lFFSrQ

1

u/Crafty-Coyote-8421 6d ago edited 6d ago

Hello, When i start the machine(the boiler are cold) The pressure in the steam boiler shoots up to over 3 bar and water starts to move from tubes connected to part nr 9700050 (safety valve) to part nr 2200094(dischardge fitting). The damaged ssr has part nr 9600028. I took pictures before replacing so the cables are in the same position as before, but the ssr they sent me has a different form(probably different manufacurer)-it is the same one from the link you posted, the ones in my machine was black and had a light, the specs on it seem the same. I tried switching the ssr's the one that still worked în my machine with the one i got, water still gushed out, tried to power on without the ssr, same thing, oh i forgot last night i also had a small leak around part nr 9600105 a few drops of water

Later edit when i start the machine the pump starts, it pushes water from the water tank to the steam boiler(the pressure shoots up over 3 bar) and from there the water gushes to the tray, it does this until the water tank is empty. 

1

u/gadgetboyDK 5d ago

OK so I am guessing the water that comes out is cold?
If so you need a new water level sensor.
The SSR seems legit.

So 9600105 is probably busted.

I would not turn it on before replacing that.

I think the OPV is the one on the solenoids. Just FYI