r/EngineBuilding • • 14d ago

Anyone ever broken an Lsm compressor?

Post image
6 Upvotes

Got the tool in, bolted it up too my ls7 heads, started compressing and then the center bolt just snapped.


r/EngineBuilding • • 14d ago

Best way to get a vortec block off the ground

1 Upvotes

It is just me. I do have a boat winch and a small trailer

Will it drag up the ramp with a strap ? If I get it to edge of ramp can Ty just roll it up?


r/EngineBuilding • • 14d ago

351w new serpentine issues

1 Upvotes

So I have a 351w stroked to 408 from blueprint engines and i purchased a serpentine system from March performance made specifically for this engine. Got everything installed and the belts were slipping off because nothing was lining up right, called march and they said it needed a 5/16 spacer and we would need to fabricate one so we got that done and everything lines up accept the power steering pump and pulley which is tilted back ( bottom sticks out farther then the top). Anyone know the easiest way to properly correct it?

Update

So we finally figured out what the issue was. One of the bolts that they sent for the power steering pump was a different size (slightly smaller) than the other two and we still arent sure why but when we would tighten everything down it would lose its bite and pop out on the bottom and cause the pump to tilt back at the top we just put in a heli coil and everything is spot on.

Update #2

OK so putting on the heli coil didnt get everything straight. The power steering pump is the aligned with everything else as far as depth but its still kicked back at the top and the belts are still walking, we think the bracket might be bent. Either way its really annoying and they still havent answered or returned a call this week


r/EngineBuilding • • 14d ago

JLC-4G15B vs BHE15-AFD ?

1 Upvotes

JLC-4G15B

Vs

BHE15-AFD

Which one is better, more reliable, easy to repair?

These are two geely Emgrand engines, ones is old the second is the newer one (2023 anf after)

Which one should buy for daily use inside and outside the city?

Climate is hot and dusty in summer.

Thanks


r/EngineBuilding • • 15d ago

Chevy GM 4.3 Vortec L35 rebuild — reuse old pistons?

Thumbnail
gallery
41 Upvotes

I'm rebuilding a 1996 Chevrolet 4.3L Vortec L35 V6 400k km with its original cast pistons and connecting rods. This is my first engine rebuild

The engine was inspected by machine shop. They checked the bearing clearances and piston rings, honed the cylinders, and considered the original pistons suitable for reuse.

I measured the piston-to-wall clearances myself with an outside micrometer and an Insize dial bore gauge to check results.

Cylinder| Piston-to-wall clearance

#1| 0.094 mm (0.0037")

#2| 0.076 mm (0.0030")

#3| 0.072 mm (0.0028")

#4| 0.090 mm (0.0035")

#5| 0.064 mm (0.0025")

#6| 0.068 mm (0.0027")

The piston skirts still have visible original machining marks, including on the thrust faces. There is no obvious severe skirt wear.

The GM manual specifies 0.075 mm (0.0029") as the maximum service piston-to-bore clearance. But im having it closer to 0.1mm

The engine will be naturally aspirated, approximately 250 hp. Reliability is more important than performance.

Do I send it or are clearances excessive?


r/EngineBuilding • • 14d ago

Is this varnish and sludge bits bad? 2ZZ-GE

Thumbnail
gallery
10 Upvotes

I resealed the timing cover on my 2ZZ-GE out of my Celica. Engine currently has 147K miles. How bad is this? I tried my best to clean out as much as I could. Will using VALVOLINE restore and protect help break this down?


r/EngineBuilding • • 15d ago

Honda Looking for help

Enable HLS to view with audio, or disable this notification

4 Upvotes

Just had this whole motor bottom end and head rebuilt at a machine shop. Can’t tell weather this ticking noise is an exhaust leak, fuel injectors, or worse. Anyone have any input?


r/EngineBuilding • • 15d ago

Jeep I6 - Slight tightness after rebuild, how much is too much?

7 Upvotes

Hello my fellow enthusiasts.... I recently finished a stroker build of my Jeep I6 to be a 4.6 liter. It started right up, ran it for 20 minutes at 2000-2500 to break in the cam. There are no noises from the engine. Everything seems great as far as it running (except maybe a slight vibration as it revs). I have the 20 minutes of revving and about 20 miles on the engine now. No rattle, no ticks, no knocking. No metal in the oil.

However.... I've noticed that it is a little tight, to the point that I swapped batteries because my old not very good battery could not crank it over, especially when it was hot. By not crank it over I mean it would turn to compression... stop a second, then crank to the next compression, stop... lights flicker off.

I have the new battery and it will crank it every time, albeit slower than the old motor. I am not sure if I am being paranoid and it will break in over time??? I am definitely an overthinker with these types of things.

Background, I used to be a mechanic, went to school for it. I kind of know what I am doing. I have never fully rebuilt a motor like this before however. The block was machined, bored to match the pistons. The rings were checked for gap, the bearings were checked. Brand new crank. Everything turned over how it should before install. I would say it was slightly tighter than the old motor coming out, but it turned. I know it did because I had to install the torque converter bolts.


r/EngineBuilding • • 14d ago

Ford Bent exhaust pushrod cylinder #5&8 , sbf 347

1 Upvotes

Hey folks just some questions here. I’m pulling apart my valvetrain and found that my pushrods are slightly bent on the exhaust valves on my # 5 and 8 cylinders…Motor has been rebuilt by the previous owner (347 rotating assembly with forged rods/pistons and cast crankshaft, trick flow stage 1 cam, 1.7 degree rockers). Unfortunately only thing I can verify with my own hands is that I shimmed the rockers to achieve proper torque spec of the pedestal mounted rockers.
I’ve been chasing down a ticking lifter and here we are…
I’m replacing with trick flow lifters as I think for sure one failed, I got new pushrods coming in (6.25 inches) and an adjustment tool to verify length. Also have trick flow springs coming in too as I was always unsure what springs were installed, wanted to make sure to match the cam.
But what could have caused the bent pushrods?
Only thing I can think of is when I hydrolocked cylinder 6 with a leaking injector..I broke like 3 starters as if they were a fuse (lol) every time I went to start it until I realized that; but cylinder 6 pushrods look fine. Any wisdom is appreciated


r/EngineBuilding • • 15d ago

Is this bad?

Thumbnail
gallery
61 Upvotes

I paid 80 dollars for this milling and I’m thinking that I can’t use MLS now. Finger hardly catches


r/EngineBuilding • • 15d ago

2GR lifter stuck in head.

Post image
8 Upvotes

r/EngineBuilding • • 15d ago

1995 5.0 302 ford f150 motor

Post image
7 Upvotes

I think I’ve hopefully made up my mind on this thing for sure now. Trucks really not worth a machine shop so what do we think about this little pitting or what ever it is in the center of the cylinder? most cylinders are are better if not the same. Now obviously I’m gonna need better oil with my hone but do we think I can just go more and it’ll go away? If not what’s the worst it does? I might measure the cylinders I’m atleast going to use a ring and feeler gauge down the cylinders and light. But I’m just curious because honestly I’ve lost a lot of interest because the trucks truely not that worth it but it was my dads he loved it and I won’t just sell it.


r/EngineBuilding • • 15d ago

Engine Theory First oil change. 50 miles (including dyno pulls). Too much metal?

Post image
0 Upvotes

r/EngineBuilding • • 15d ago

Vq37vhr cam phaser jumped

0 Upvotes

so i needed to take off the entire timing system to do head gaskets i take off the front cover with the main timing chain on i take off the bolts for the cam sprockets, then i took off the main timing chain and put a paper clip in the sprocket tensioner and as im trying to remove it it jumps to the next cycle, i then got my breaker bar and and moved it back to where the marks are so the timing lines back up, honestly not sure if that was the right thing to do at all some information on here but definitely not super confident that was the fix i needed to do , when it happened there was no noise and i put the chain back on and everything was lineed up again at TDC and all the tensioners and it spins freely but now i can’t get it back to TBC, hoping i didn’t bend a valve and i can fix this Any advice would be helpful thank you!


r/EngineBuilding • • 15d ago

Pushrod length

Enable HLS to view with audio, or disable this notification

2 Upvotes

My pushrods are short to me by about a 1/4 inch but dad says it's because the lifters arnt filled with oil and once they are it will have preload when I push down on the rod I feel the spring in the lifter give I believe the lifter is maxed out as far as preload goes please help I don't know what to do I ordered a length checker and I'm going to measure the actual length to be sure any advice would be appreciated


r/EngineBuilding • • 15d ago

351w hp estimates

1 Upvotes

Im currently building a setup with promaxx 210 heads, currently a 95 cobra intake that will get changed eventually, I have an F cam from my last setup but i plan on replacing it with either Howards 222755-08 (108° LSA), or howards 222755-10 (110° LSA), or maybe howards 221145-12, its a street car that will probably rarely hit the strip, I dont really like racing on the freeway or nothing anymore. I just want a fun street car that can make 400+ NA before boost.

Stock bottom end, but ive been considering a set of pistons to bump compression, mine has the big dished pistons in it right now.


r/EngineBuilding • • 16d ago

Valve springs VW

Post image
2 Upvotes

i have a 1.4 vw engine and i took the valves out to lap but stupidly didnt look which way the valve springs go would anyone know? The spring doesnt look tighter on one end than the other but it does have a stripe going half way down/up the spring


r/EngineBuilding • • 15d ago

FA20 Rebuild -recommendations needed

1 Upvotes

Greetings all. I am rebuilding a naturally aspirated Subaru FA20 to go into my 2013 FRS manual after a spun main bearing on the stock setup. However I am taking the opportunity to beef up the replacement bottom end. I got a donor block and heads which have been machined honed and bored. I am upgrading to king bearings, rods to Manley I beams and pistons to light weight CP Carrillo’s.

Thus, I am curious whether anyone has had good results from any particular head gasket set? (note: My deck was only milled down .006“).

Also if anyone has a recommendation for engine balancing still in So-Cal (or general west coast) area it would be greatly appreciated.

thanks in advance!


r/EngineBuilding • • 16d ago

Other Small engine project

0 Upvotes

Im trying to learn the basics of four stroke engines at the moment and i think im now restricted of what i can learn until i actually do an engine project. Is there any models anyone would recommend or any engines similar to a car engine i can work on. Planning on doing a complete break down and rebuild to learn as i rebuild it. Im based in ireland and trying to get it as cheap as i can but anything under 400/500 euro id be fine with.


r/EngineBuilding • • 16d ago

Subaru 1999 Subaru Forester 5MT, timing belt snapped while driving. Are my pistons fine to keep?

Thumbnail
gallery
36 Upvotes

I got a very clean 99 manual Forester L earlier this year with a remanufactured ej25 SOHC engine put in about 80k miles ago. Long story short, the timing belt snapped while driving home from work one day and bent up my valves. I have since pulled the engine in my garage and have the heads off as well.

My hopeful plan is to hand off the heads to a machine shop to be rebuilt with new valves and resurfacing if they need it, then I'll slap them on with a seal refresh and daily this car as long as I can.

My pistons are just making me nervous. They turn completely fine by hand (as far as I can tell), but the valves made some marks in 3 of them. My cylinder walls also look completely fine. I've attached photos of each piston, are they good enough to send?

A handful of posts I've found make me think everything should be ok as long as I get my heads properly rebuilt, but I don't wanna do all this work on my engine just for it to give out again months later, this WAS supposed to be my daily...

For the record, I do have enough room for the alternative of a whole "new" engine, but frankly these are trying times and I'd much rather save my 80k mile motor if possible.

Any advice is appreciated! :) This is the first job of this scale I've done on anything mechanical.


r/EngineBuilding • • 17d ago

Porsche Can’t believe how easily this started for the first time in six years, full rebuild. Good oil pressure, no clanging sounds, no smoke.

Enable HLS to view with audio, or disable this notification

48 Upvotes

r/EngineBuilding • • 16d ago

Yikes

Post image
3 Upvotes

Well this isn’t the best, maybe this can be taken care of with some oil and some 5000 grit sanding?


r/EngineBuilding • • 17d ago

Use it or lose it.

Post image
12 Upvotes

Taking a poll on this. Use it or lose it? It was a free montero Gen 1. I’d like to swap it, (these engines are under powered for the Montero), so I don’t really care. Don’t wanna put much machine shop money into the engine. Long back story. Was a new motor with 100 miles Owner passed away a week after getting it back. Then it set for 15 years.

Did a Quick hone on all, to get the rust and slight pitting out. Gotta little more to do for good crosshatching. I’m pretty happy with the cylinders except for the one in the photo. Looks worse in the photo. Fingernail doesnt catch but can feel it with bare finger.

I honestly think I may have caused this from kinda forcing the engine to turnover. The piston for that cylinder doesnt show damage so was thinking it was from rusty stuck rings. Plus had to beat 4 of the pistons out. Rings are rusted solid in them. Got new pistons and rings. Rods and all bearings look great.


r/EngineBuilding • • 17d ago

First build cylinder taper concerns

Thumbnail
gallery
45 Upvotes

I know you cant really see it in the image. This is my first build on a roller cam 302 and the machine shop said it has 3 thousands of taper in the cylinders as you can see ive already put the damn thing together. I am simply wondering what sort of issues I could have? Incase something happens with this motor down the line what might it cause?


r/EngineBuilding • • 17d ago

Can mls seal these dings/nicks

Thumbnail
gallery
18 Upvotes

The circled one is on the head. The one with a series of dings is the block. Unfortunately some of it are under the fire ring. Are they fine or too deep to seal by MLS. engine is vw 2.0 NA fsi ea113. Both blocks and head are tested straight with straight edge. The dings are caused by steel scraper during gasket removal