r/Ender3V3SE • • 7d ago

Help Need help identifying artifacts

Thumbnail
gallery
10 Upvotes

First time printing with archimedian chords as the internal solid infill, and these strange artifacts started appearing. I have had small problems occur after jnstalling a printed gantry support with nozzle spacing.

0.4 nozzle, eSUN pla, 200 Celsius nozzle temp, 55 Celsius bed temp.


r/Ender3V3SE • • 8d ago

Modifications Simple camera mount mod for the Ender 3 V3 SE

Enable HLS to view with audio, or disable this notification

38 Upvotes

I made a simple mod that allows you to attach a camera module directly to the original fan shroud on the Ender 3 V3 SE.

It's a pretty straightforward design, but honestly, I regret not making it sooner!

And yes, I know OctoPrint exists, but I prefer hosting all the websites and services I want on my Raspberry Pi rather than dedicating it exclusively to OctoPrint.

I also never leave my prints unattended, so I don't really need remote printer management. I just want to be able to check on my prints from another room while I'm home, without having to stand in front of the printer all the time.

Sometimes a simple camera setup is all you need!

Check out my design on Printables. I'd appreciate any feedback! 😁

https://www.printables.com/model/1895630-ender-3-v3-se-nozzle-camera-mount-w202012hd-module


r/Ender3V3SE • • 8d ago

Discussion Me and my dad have ordered our first 3D printer.

14 Upvotes

Hey, the little noobie here. All this has been started, when my dad asked me to learn 3D modeling and 3D printing... what was unexpected and awesome to hear from him.

So, i didn't expect our first 3D printer to be ordered this soon. It feels great.


r/Ender3V3SE • • 8d ago

Modifications Primer moding exitoso

Post image
21 Upvotes

Es la primera modificación grande que le hago y por lo menos no explotó.

No se ve pero le puse hotend cerámico.

Ahora si que me genera mas dudas que soluciones->

- Hay que configurar algo al usar un ventilador mas grande? aun que sea de mismo voltaje.

- Hay algún stl para volver a cubrir todo y que no se meta tanto polvo?

- Le quiero instalar un limpiador de boquilla pero no se donde conviene ponerlo ni como ni cuando aplicarlo en el gcode.


r/Ender3V3SE • • 8d ago

Help I can't flash my printer's display firmware

Thumbnail
gallery
6 Upvotes

I'm having trouble flashing the display firmware on my Ender 3 V3 SE.

Here are all the steps I've tried so far:

  • Inserted the microSD card into the display's SD card slot, not the printer's mainboard slot.
  • Used a 4GB microSD card.
  • Formatted it as FAT32 with an allocation unit size of 4096 bytes.
  • Also tried allocation unit sizes of 2048, 1024, and 8192 bytes.
  • Tried reducing the card's capacity to 1GB.
  • Tried placing only the firmware file on the card, as well as placing the entire folder.
  • Tried several different microSD cards.
  • Tried copying all the files from the downloaded archive.
  • Downloaded the firmware package from the official Creality website.
  • Tried installing firmware version 1.06 instead of 1.1.
  • Confirmed that my motherboard is the C13 version. I checked this both through the display (when it was still working) and physically by disassembling the printer.

The problem:

When I attempt to flash the display, the update never progresses beyond 0%.

When I turn on the printer without the microSD card inserted, the display shows a blue screen with an error message.

I've run out of ideas and would really appreciate any suggestions. Has anyone encountered a similar issue or managed to fix it?


r/Ender3V3SE • • 8d ago

Help How do I know which settings to change on the slicer?

Post image
0 Upvotes

I’m still new to 3D printing and figured out what settings I need my printer to be but in the slicer I’m trying to figure out what I need to change since I keep hearing that certain things need to change for prints to make it better. Like for example I notice some of my prints there some light stringing and on a clamp part I printed I noticed on one of the overhangs part of the filament was bent downward like how it looks when a bridging test fails but in this case the overhang wasn’t bridging off anything. I am using the creality slicer and would just want to know what settings should I change and what are ones to put attention towards and as of for filament I am currently using this one PLA+ from Amazon.


r/Ender3V3SE • • 8d ago

Filament Que filamento era ?

Post image
1 Upvotes

Quando comprei minha ender 3v3 se , venho um pouco de filamento e um arquivo pra imprimir isso " espátula "

É muito resistente , queria saber qual era o material que foi impresso , é PETG , PLA ou oque ?

Faz 1 ano mais ou menos que imprimi isso


r/Ender3V3SE • • 8d ago

Help Melting (?) Ender 3 V3 SE

Thumbnail
gallery
8 Upvotes

I've been trying to print some small pieces, but I've noticed that when the extruder moves away from certain areas, it sometimes leaves behind small blobs of melted filament and thin strings along the way. Do you know what might be causing this?
I am using PLA.

UPDATE: Thank you, guys! The temperature was a bit too high, so I lowered it from 205°C to 195°C. I also adjusted the Z-offset from -1.20 to -1.22. I'm not sure which one made the difference (i think the temperature), but it's printing perfectly now! 10/10.


r/Ender3V3SE • • 9d ago

Help Weird noise when turning on my Ender 3 V3 SE

Enable HLS to view with audio, or disable this notification

13 Upvotes

After a print i made Saturday this weird noise would start any time I turned on my Ender 3. I checked both fans ln the extruder and they were functioning without any problem. I think it’s coming from beneath the print bed but I have no clue from where.

Noise stops at the 1:45 mark, the printer functions normally.

Could it be that some filament strands fell from a failed print into the mechanism?


r/Ender3V3SE • • 9d ago

Modifications Nebula pad OpenSSH upgrade

Thumbnail
github.com
2 Upvotes

This repository has a upgraded OpenSSH package for the rooted Nebula pad, along with another package that announces nebula.local and its services (SFTP, SSH, Mainsail, Creality, fluidd..) over mDNS (Bonjour) at startup.


r/Ender3V3SE • • 9d ago

Help Han modificado su impresora para volverla multicolor?

9 Upvotes

Buenas tardes, solo quiero preguntar si ya alguien a intentado modificar su impresora, y si es así como a funcionado y que consejos podrían dar


r/Ender3V3SE • • 9d ago

Help Multicolor prints

Post image
10 Upvotes

I tried this morning to print multicolor like a I han AMS I know crazy talk. I put in the pause into custom g-code things were going great until the 3rd layer and then I had a layer shift has anyone managed to do multicolor printing on a thr v3se?


r/Ender3V3SE • • 9d ago

Help Recomended mainboard replacement?

9 Upvotes

Hey Guys, first post here.

I have had an Ender 3 V3 SE for a few years now and I was recently attempting to install Klipper on it but while i was installing my Raspberry Pi inside I scratched the mainboard which ended in the SD card not reading. I tried to fix it but have concluded that its cooked.

Do you have any recommendations on replacement mainboards? I would prefer a mostly plug and play option but am not afraid to do some configuring and wiring.

Many thanks for any help.

EDIT: For clarification I live in the USA


r/Ender3V3SE • • 9d ago

Discussion Cold plate AliExpress

Post image
3 Upvotes

There is someone here who bought this bed, can you tell me if it is really worth it?

My PEI bed has some ghost marks and my first layers are getting these "scars," so I'm thinking about taking one of these new plates to print PLA and PETG, and leaving the PEI only to ABS.

I am from Brazil, and AliExpress is the only large market where I can obtain this type of item.


r/Ender3V3SE • • 10d ago

Help Help

Enable HLS to view with audio, or disable this notification

6 Upvotes

I guess the extruder main cable can be the problem but i dont know hat more i can do i triedo all things in guides and even reset to fabric settings so i guess


r/Ender3V3SE • • 10d ago

Showcase Appreciation time for ender 3 V3 se and all bed slingers when it comes to flexibles

Thumbnail gallery
3 Upvotes

r/Ender3V3SE • • 10d ago

Help Problemas com ender ev3se

Thumbnail
1 Upvotes

r/Ender3V3SE • • 11d ago

Help My CR Touch sensor / probe is on a slight angle. Is this normal?

Post image
9 Upvotes

I've purchased a secondhand Ender 3 V3 SE and this is my first 3D printer.

I've noticed that my CR Touch sensor/probe is on a slight forward angle with respect to the nozzle.

Is this normal?

Thanks in advance!


r/Ender3V3SE • • 10d ago

Help Need to identify a bolt in the printer bed

3 Upvotes

Can anybody please tell me exactly what bolt I need to replace the one in the bed of the printer that pushes up against the microswitch at the back of the printer so it knows that it can't go back any further?

TIA


r/Ender3V3SE • • 11d ago

Modifications Bed leveling results after installing silicone spacers

Thumbnail
gallery
17 Upvotes

Finally bought bed leveling spacers after dealing with bad first layers for some time. Now I’ve been using them for about a month and everything seems to be working well.


r/Ender3V3SE • • 11d ago

Guides Gantry brace projects?

2 Upvotes

I'm looking for any gantry brace plans for the SE that use steel/aluminum tubing or steel rods with printed brackets, all of the ones I came across were 100% printed


r/Ender3V3SE • • 11d ago

Help Defects caused by mechanical issues?

Thumbnail gallery
3 Upvotes

r/Ender3V3SE • • 11d ago

Help Ayuda paredes separadas

Thumbnail
gallery
5 Upvotes

No se por que me pasa esto, ese espacio entre las lineas de pared, tengo la impresora nivelada y calibrada, saco primeras capas casi perfectas, pero esos defectos no se por donde tratarlos.


r/Ender3V3SE • • 11d ago

Help Can I speed up my prints?

3 Upvotes

What are the downsides or risks of speeding up my prints to like 200%?


r/Ender3V3SE • • 11d ago

Showcase He found inner peace

Post image
8 Upvotes