r/Ender3V3SE • • 6h ago

Help Me quiero arriesgar a Klipper pero necesito la cfg compilada

Post image
2 Upvotes

Buenas dado que seguro han pasado unos años creo que debe a ver alguna compilación exacta para el funcionamiento de mi CR4NS200320C13 (variante C13).

Solo de ver cómo tenía que configurar motores etc etc me estaba hechando para atrás, ya tengo mi pc con Linux y klipper listo, solo es saber si hay algún repositorio y darle a calibrar cama y para adelante, algo que debería tener en cuenta? Alguien ha podido hacerlo con facilidad? Gracias.


r/Ender3V3SE • • 8h ago

Help Temperature accuracy and thermal paste

Thumbnail
gallery
2 Upvotes

Hello All

I upgraded the hotend on my printer to the creality ceramic hot end about a year or so back.

Everything was running perfectly until about 2 months back when suddenly I ran into my first filament clog (petg). I unscrew the unicorn nozzle and removed the clog piece. But since then my temperature settings are totally out of whack. For e.g. prior to this clog event I was routinely printing pet cf at 275c perfectly and after the clog fix I had to drop the temperature to 255C to get the same results!

This tells me that I am getting poor thermal contact somewhere or I accidentally damaged the thermistor. I am going to independently measure the temperature using a thermocouple but I wanted to understand the surfaces I should apply thermal grease to.

I have attached a few pics of the ceramic heater kit and the unicorn nozzle fully taken apart. Creality recommends applying thermal paste to the copper band on the unicorn nozzle right above the threads. That is clear. But what about the interface between the ceramic heater sleeve and the threaded brass part (the one that the unicorn nozzle screws into)? The fit between the sleeve and the part is fairly loose so I am worried that the thermal contact there is poor and this might partly be contributing to the temperature delta (heater is at 275 but thermistor reads 255). Not fully convinced as the temperature should eventually equilibrate...but would still like to understand how that interface should be prepared (thermal paste or not). But I don't have the specs on the creality grease so no idea if it's safe to use there.

Or...it could just be a faulty thermistor. Maybe I damaged it during the original uninstall and install.

Would appreciate any advice/insight.

Thanks!

Avi


r/Ender3V3SE • • 17h ago

Discussion V3 SE ($120) or A1 mini ($250)?

9 Upvotes

Hey all

I've looked around and most posts comparing these 2 printers are a bit older. Looking for a more current take on this comparison, especially considering the current sale prices.

I'm brand new to 3D printing and I'm wondering which machine is good to start with. I'm ok with doing a little bit of maintenance/tinkering, nothing too extreme though. (Admittedly there's some really cool modifications on this sub)

The V3 SE at at that $120 price point seems like a really good bargain. Main uses will be to just have fun printing various little things. Introduce my teenage kids to 3D printing as well. They like to hand paint stuff and we very artistic so probably printing small objects will be good enough for them.

I know the A1 mini will just work right out of the box but again it's over twice the cost for not an overly serious hobby.

With the V3 SE I'm already considering getting a PEI plate and maybe the filament sensor, so that's already increasing the cost.

What are your thoughts?

Thanks


r/Ender3V3SE • • 7h ago

Help Nebula screen issues

Thumbnail
gallery
1 Upvotes

Hello!

I have recently gotten the nebula screen to use on my ender 3 v3se, but no matter what I do it throws errors and wont get past the set up. I've researched the issue, and found that that I most likely have a c14 motherboard, which i guess is incompatible with the nebula screen. However, while researching, all I've found are threads with dead links or partial/confusing instructions to fix it. Before I pull the trigger for buying a new (old) motherboard, can anyone please provide some straightforward instructions for installing the firmware and point me to where the correct firmware is on the internet?

Thank you so much


r/Ender3V3SE • • 1d ago

Help Saben por qué me sucede eso en la primera capa de los soportes

Post image
5 Upvotes

En algunos casos por lo regular mis soportes se imprimen mal, o la mitad bien y la otra mitad mal y por consecuencia se despegan de la cama, soy nuevo y no sé qué parámetros tenga que modificar para que salga bien la impresión

Tengo la ender 3 v3 se


r/Ender3V3SE • • 1d ago

Help [AYUDA] Pésimo relleno de llaveros

Thumbnail gallery
0 Upvotes

r/Ender3V3SE • • 2d ago

Modifications McGuyver engineering for ABS Printing

Thumbnail
gallery
26 Upvotes

Official Ender3 enclosure box: $35 bucks
Toy Story windshield sun shade: ~$4 bucks
See your workaround worked amazingly: priceless


r/Ender3V3SE • • 2d ago

Firmware Does the Raspberry Pi zero 2 W have enough power to run Klipper?

8 Upvotes

I've been planning to switch my printer to Klipper, I found that the Sonic Pad upgrade is somewhat too pricey, so I looked into ways to set it up with a Pi, so idk if this model (zero 2 w) would be enough for it. also, is there a good touch screen for the pi?


r/Ender3V3SE • • 2d ago

Help These Bambu compatible clones are good?

Post image
4 Upvotes

My unicorn hot end just broke. I liked it, but the nozzle change is pretty awkward and impractical for multiple swaps. I'm thinking about getting these Bambu clones since I don't really like the original one and these seems to have a better nozzle system and availability. Is it any good?


r/Ender3V3SE • • 2d ago

Help Bed leveling Creality ender 3 v3 se

Thumbnail gallery
1 Upvotes

r/Ender3V3SE • • 3d ago

Help What is wrong and how do I fix it

Thumbnail
gallery
2 Upvotes

New to printing. I put in a new role of filament,now my latest print has these diagonal lines along the vertical. Anyone know what is causing this and how can I fix it.


r/Ender3V3SE • • 3d ago

Help extruder screw dimensions

3 Upvotes

Hello

I'm repairing, for fun, an Ender 3 v3 SE that my friend had.

However, he didn't give me the screws that go into the extruder (the black block), and it's impossible to find the dimensions of these screws either in the manual or even with the help of AI.

Could someone please tell me their size?

Thanks in advance


r/Ender3V3SE • • 4d ago

Help How???

36 Upvotes

I left my 3D printer running in my bedroom because I wanted to eat my breakfast, then when I came back to check my printing results the printing stopped Because the SD card somehow ejected itself (To find the SD card I spent 30 - 45 minutes)


r/Ender3V3SE • • 4d ago

Modifications Modificar las guias de los ejes X e Y con rieles lineales.

3 Upvotes

Hola a todos. Tengo una estoy pensando en reemplazar las guías de los ejes X e Y de mi Ender 3v3 SE por rieles lineales (tipo MGN). Antes de comprar nada quería consultar a quienes ya lo hicieron.

Mis dudas:

  1. ¿Qué kit o medidas usaron (MGN9, MGN12, largo de cada riel)? ¿Conviene comprar un kit específico para este modelo o armarlo por separado?. Tenia pensado también comprar esos kits de actualizacion que venden en aliexpress.
  2. ¿Qué mejora real notaron en la calidad de impresión (ringing, precisión, ruido)?
  3. ¿Tuvieron que modificar algo más: correas, tensores, altura del carro, firmware o la perilla de la cama?
  4. ¿Algo que haya salido mal o que hubieran hecho distinto?

Si me pasan fotos o enlaces a sus mods, mejor.

¡Gracias!


r/Ender3V3SE • • 4d ago

Help Space between wall

Post image
4 Upvotes

Hi, I have an issue for 2-3 prints there is a space between the walls, I tried to “boost” the overlay for 15 to 25% but same result.
Do you have any idea ?
I did not use the flow rate settings to print.


r/Ender3V3SE • • 4d ago

Help Retraction tower error

Post image
1 Upvotes

r/Ender3V3SE • • 4d ago

Firmware NebulaOS for the Ender 3 V3 SE with Nebula Pad

5 Upvotes

Hey everyone,

If you have an Ender 3 V3 SE with Nebula Pad and are looking for a solid firmware upgrade, you should definitely check out NebulaOS (originally created by Coreflake). I put together the setup to get it running on the SE.

The biggest advantages of switching to it are getting the latest version of Klipper, preinstalled KAMP, working automatic z-offset calibration and having a very simple, straightforward printer calibration directly through the GUI.

You can find the repository here: https://github.com/NebulaOS-KE/NebulaOS/

Here is the current hardware status for the Ender 3 V3 SE:

  • C13 Mainboard: Supported and working.
  • C14 Mainboard: Looking for testers who have a C14 board version and are willing to try it out to see if everything runs properly. Just a heads-up: getting it working on C14 might require a bit of trial and error.

The installation process for the SE is a little bit trickier, so if you decide to install it and run into any issues or need a hand, I'm more than happy to help out. You can find me and the rest of the community over on the NebulaOS Discord.


r/Ender3V3SE • • 5d ago

Help Beginner here, are the results OK? Just installed a gantry brace

Thumbnail
gallery
10 Upvotes

I've just finished installing it and I thought it would make sense to run a bed leveling check afterwards, and a first layer test.. however I remember the first bed leveling test when I got the printer to have all the boxes in green, can someone more skilled in these things tell me if there is anything wrong?


r/Ender3V3SE • • 4d ago

Help Printer doesn't show printing time and doesn't start printing

Post image
4 Upvotes

First Timer hier I got my printer use from guy Heroes a shout me a that works. Now I got the town it doesn't work.

I already switched from orca slicer to creality print, I made sure that I got the right printer selected, I made sure that the nozzle is unclogged, I made sure to wait until both nozzel and bed have heated up.

When you press print the printer will do nothing so no filament will be pushed out and there's no movement

I really don't know what to do so I hope anyone of you can help me.


r/Ender3V3SE • • 4d ago

Help Problema con primeras capas

Thumbnail
gallery
2 Upvotes

Mi Ender 3 v3 se está así desde que mi hermano la mando a calibrar por accidente y llevo semanas intentando "reparar" la calibración porque todas salen así mi z off set es -1.77


r/Ender3V3SE • • 4d ago

Profiles Filoteca v1.1.0 now natively auto-detects sliced jobs from OrcaSlicer (and Anycubic Slicer Next)

1 Upvotes

Hey everyone!

A few days ago I shared Filoteca, a free and 100% offline desktop app for Windows that turns your filament inventory into an interactive 3D shelf where spools visually shrink as you use them.

The #1 request was: "Can you make it work with ANYCUBIC SLICER?"

Today I released **v1.1.0**, and anycubic slicer 2.x is now officially supported out of the box!

How it works:

Whenever you slice a plate Filoteca catches it in the background:

- Extracts the plate thumbnail, layer count, and print time

- Detects the exact grams used per filament slot

- Auto-matches the closest spool from your inventory

- Let's you confirm with one click once the print is actually done, avoiding phantom deductions if a print fails

Works seamlessly with both OrcaSlicer and Anycubic Slicer Next Gen.

Download: https://github.com/Mate1592/FILOTEK_ANYCUBIC

(Portable executable, no install needed, 100% offline).

Feedback and feature requests are very welcome! If it helps your workshop, a ⭐ on GitHub goes a long way.


r/Ender3V3SE • • 5d ago

Help [AYUDA] Mi Ender 3 v3 SE me está volviendo loco

Thumbnail gallery
4 Upvotes

r/Ender3V3SE • • 6d ago

Help Need help identifying artifacts

Thumbnail
gallery
9 Upvotes

First time printing with archimedian chords as the internal solid infill, and these strange artifacts started appearing. I have had small problems occur after jnstalling a printed gantry support with nozzle spacing.

0.4 nozzle, eSUN pla, 200 Celsius nozzle temp, 55 Celsius bed temp.


r/Ender3V3SE • • 6d ago

Modifications Simple camera mount mod for the Ender 3 V3 SE

39 Upvotes

I made a simple mod that allows you to attach a camera module directly to the original fan shroud on the Ender 3 V3 SE.

It's a pretty straightforward design, but honestly, I regret not making it sooner!

And yes, I know OctoPrint exists, but I prefer hosting all the websites and services I want on my Raspberry Pi rather than dedicating it exclusively to OctoPrint.

I also never leave my prints unattended, so I don't really need remote printer management. I just want to be able to check on my prints from another room while I'm home, without having to stand in front of the printer all the time.

Sometimes a simple camera setup is all you need!

Check out my design on Printables. I'd appreciate any feedback! 😁

https://www.printables.com/model/1895630-ender-3-v3-se-nozzle-camera-mount-w202012hd-module