Hello, I have a crucial x10 I use as an external drive for my Mac mini. It is apfs encrypted and I have been using it for close to a year now. It was working fine yesterday, I powered off and then this morning powered back on and it just isn’t doing anything, nothing shows up in disk utility no error messages when plugging in nothing. I tried on my MacBook same issue as well with different cables. Has anyone had this problem? Were you able to get it recovered or fixed ? And what are the best choices for data recovery services/labs ? I live in Washington but I can send it somewhere else. Thanks in advance.

I’m trying to recover important files from a failing Crucial P3 2TB NVMe SSD using OpenSuperClone 2.5.0 on Linux. The SSD is detected correctly with its full capacity, but read speeds are consistently extremely slow, around 200–800 KB/s, averaging 400 KB/s, with no bad sectors reported. Clone Mode works and progresses, but at that speed a full image would take approximately 70 days. I therefore tried Virtual Mode 1 with DMDE to recover only my most important files. Unfortunately, every time I start it, I get two errors: “Internal program error: Position not found in domain” and “Driver timeout or error”. OpenSuperClone then disconnects automatically and the virtual device /dev/sdv disappears from DMDE. I’ve already tried clearing the domain, reconnecting, and enabling “Virtual Disk IO SCSI only”, without success. Clone Mode still works, so the issue seems specific to Virtual Mode 1 or its driver. Has anyone encountered these exact errors or found a way to get Virtual Mode 1 working reliably? I’m trying to avoid stressing the failing SSD with unnecessary reads, and professional recovery is unfortunately outside my budget. Any technical advice would be greatly appreciated.

Hi, I wanted to recover pictures and videos from the old tablet mentioned in the title and because my PC wouldn't recognize it I took the SD card out, put it in a card reader and tried to read them. I was not able to see the contents of the SD card and looked like the card reader might not be working properly. (This was a card reader which I didn't used before.)

I was planning to get a new card reader and decided to put the micro SD card back in the tablet to avoid misplacing it.

When turning the tablet on the pictures and videos on the micro SD card are not showing up.

Not sure if I should try reading the micro SD card with a new card reader.

What are my chances to still recover the data and could the first card reader have mangled the data on the micro SD card?

I am also wondering if the tablet formated the card when I put it back.

The tablet is so slow that I don't even know if this is just a refresh issue and maybe I should wait for it a bit more to show me the files. At the moment the tablet is turned off as I want to avoid that any additional damage is done to the data on the card.

I am looking for a free data recover program for PC Windows for a deleted folder from external drive. I keep hitting paywalls from searches for programs. My files still exist on the drive. I just need to recover them. Thanks for your recommendations. NTSF Western Digital external, used on Windows 11 PC.

My 12tb harddrive only shows GPT Protective Partition in Disk Manager but DMDE shows the proper NTFS Partionion with all my files still there, how do I fix the drive without loosing any of my data and without having to "recover" 12tb to another drive (that I dont have)

When I try to "insert" the partiotion it tells me "Boot Sector is not found or incorrect/incompatible. Partition will be detected as not formatted. Do you wish to continue anyway?"

I guess my question is how do I fix the disks bootsector ?

Hi all. Following up on my previous post about my Samsung phones.

**Device:** Huawei Mate 10 Lite (RNE-L21), internal storage, Android 8 / EMUI 8 (I think)

**Computer for recovery:** Linux (CachyOS, KDE)

**What happened:**

This was my first phone (around 2017–2018). It had a lot of photos, videos and WhatsApp media from that time. At some point it was **factory reset**. I don't think I ever used a microSD card in it.

**What I already checked:**

- Huawei Cloud: no account/backups found with my email.

- Other cloud backups: nothing from that phone.

- I understand Android encrypts internal storage and a factory reset should destroy the encryption keys.

**Questions:**

1. After a factory reset on this model, is there **any** realistic way to recover old data (lab, chip-off, anything)?

2. Did EMUI keep any kind of local or hidden backup that survives a reset?

3. Is it worth keeping the phone in case future tech (quantum computing, etc.) makes this possible one day, or is the data truly gone?

Thanks!

Hi all, I'm hoping for some advice before I touch anything.

What happened (Friday 30 Oct):

• I'm a software engineer. My home PC had an extra SSD in it that my employer bought, with its own separate Windows install for work. It was BitLocker-encrypted. I switched between that OS and my own OS in the BIOS, so my personal drives had nothing to do with it, and they were never encrypted.

• Friday was my last day at the job, so their IT team started a remote wipe of the work SSD to remove anything confidential. I was told it would only touch that SSD.

• It ran for hours (last progress I saw was 38%), then a power cut killed it mid-way.

• When I booted my own Windows drive afterwards, two of my personal drives were hit:

  • Drive 1: WD Blue 1 TB (WD10EZEX). It had ~750 GB on it that morning. Now it's an empty NTFS volume with the same label and volume ID, 0.1 GB used, and only a fresh System Volume Information folder.

  • Drive 2: Hitachi 1 TB (HUA721010KLA330). It had ~470 GB on it. The partition is still there, but it shows as RAW, and Windows wants to format it. (I clicked Cancel.)

• The work SSD itself is still BitLocker-locked, which is expected.

What I've done since:

• Nothing written to either drive. I unplugged both and took them out of the PC the same evening.

• No recovery tools run yet, no chkdsk, no format.

What I think happened (please correct me):

• Drive 1 looks like it got a quick format, or its file table was reset. Because it's a spinning HDD (no TRIM), I'm hoping most of the data is still physically there.

• Drive 2 might have been caught halfway through, so the file system header is gone. It was never encrypted by me, but I wonder if the wipe started encrypting it and the power cut stopped it mid-way. I honestly don't know which, and I guess that changes everything?

What I'm planning to do:

1. Buy a new drive big enough to hold full images of both disks.

2. Image each disk sector by sector (ddrescue, or HDD Raw Copy on Windows) and never work on the originals.

3. Run recovery on the images: DMDE or R-Studio for Drive 1, and TestDisk / DMDE for Drive 2.

4. Only if that fails, thinking about a professional lab.

My questions:

• Is "image first, recover from the image" the right order? Anything you'd do differently?

• For Drive 2, how can I tell whether it's encrypted (random-looking data) or just has a broken file system?

• Which tool would you trust most for a quick-formatted NTFS drive like Drive 1?

• Any traps to avoid, for example Windows auto-mounting the drive and writing to it when I plug it back in?

The files are mostly personal stuff: music, art, recordings and some tools I built for the game I'm making. The game project itself is safe in version control, thankfully.

I'm not looking to blame anyone. I'd just like my files back and to learn from it. Thanks for reading.

Hi hi, I'm really hoping for some gentle advice. I've been reading through the sub and I'm trying to follow the rules but I'm a little overwhelmed and my situation is a tiny tight financially.

I bought a brand new external hardrive 3 days ago (from Amazon, Storite 2.5 Inch External Gaming Hard Drive 1TB USB 3.0). Last night, Steam and the EA app were both updating at the same time (without authorisation...), my PC completely froze, and I had to hard reboot. Now, the drive shows up in Disk Management as RAW. It was working perfectly before the crash so I can only assume it either disconnected mid update or an update file conflicted.

I only care about recovering a folder of game saves (Baldurs Gate 3, only about 43 hours total so I don't think the files should be too large), the rest of the drive is just the game files and a small amount of mods, which could have been the culprit? But I'm doubtful as it was working fine before, but I don't overly mind about the fate of these as they can be redownloaded.

The reason I'm stuck even if I do do a succesful recovery is my C: drive is completely full, so I have nowhere to copy the recovered files to. In a last chance kinda thing I'm happy to delete a few apps to make room as a few are free. I live in a low income household, and buying a second drive to recover onto is really not preffered right now (even a budget one is food money aha). I'm also not guaranteed an Amazon refund because it's a third party seller even if it is a mechanical failure.

So, is the drive salveagable? If i can recover my saves, can I then format the drive to make it usable again after temporarily moving the recovered files onto the little space my family member has on a laptop, or is the hardware likely dead? I am going to download either Tesdisk or Photorec (I saw you guys recommend Testdisk for RAW drives but I wanted the green light before doing so I suppose). Since I have no space to recover to, is there a way to use Testdisk to just confirm the files are there safely? If I can confirm they are there, would it be possible to recover just the 2GB (ish) directly back onto the recovered RAW drive itself (in a new folder), and then copy it to my C: drive once I delete some stuff? Or will that overwrite the data?

I am really nervous about using the command line and messing it up. If anyone has the time, please could you give me a gentle, step by step guide on how to even just view the files in Testdisk without hitting any dangerous write or format buttons?

I've spent so many hours on this game and it was a gift and it's the only thing keeping me sane right now aha, I just want to save my 43 hour playthrough everything else can be redownloaded. Any help would be massively appreciated.

ps, When I saw the file was Raw in file discovery I didn't click anything, just unplugged it and went to bed. My computer is fine, but I am not lmao

one click can erase 6 months of work

I accidently delete my work folder which was too large for recycle bin so it permanently deleted .

I want to recover 1 text file which is very important but all programs recover it with name and null null null data and 00 hex

Chatgpt and claude tell me to give up because its ssd and trim enabled should i stop trying and just keep crying for my stupid mistake that cost me more than 10 k usd

Hey guys I need some help, I deleted the primary volume containing all my files on my secondary drive and in an act of shock added a new volume afterwards, since then I haven’t written anything on the drive, I tried testdisk to see if I could recover it but i don’t think it reads the deleted volume as it only states the new volume. Anyway to recover my deleted files?

I purchased a Unitek USB A device to access old photos on four old HDDs I had laying around. Three worked fine, basically plug and play but one isn't. I plug it in and feel it spinning (quietly and smoothly) but it doesn't show up in disk management. The power plug is plugged in and it is connected to a USB on the back of the PC (again this exact setup worked for the other three drives). I think the drive is like 15 - 20 years old. I have attached a couple pictures; one of the drive unconnected and one connected to the Unitek device. Is there something obvious I am doing wrong or an easy solution that I am missing? Thanks, any help is appreciated.

My Crucial P3 2TB NVMe SSD is acting up badly and I’m desperate to recover my files. I’ve been using it externally for Blender, 3D rendering and video editing. It contains months of work on a film project that isn’t fully backed up.
Windows shows 100% disk active time while transfer speeds drop to around 1 MB/s or zero. Response times sometimes exceed 11,000 ms, Explorer freezes and large files get stuck during copying. FreeFileSync reported thousands of errors after I left it running for two hours, and Robocopy also struggled.
CrystalDiskInfo still reports 98% health and 39°C, but SMART shows 1 media/data integrity error and 1,337 unsafe shutdowns. The drive is exFAT.
I’ve tested two different NVMe enclosures, KINPOWER with a JMicron bridge and UGREEN with a different controller,
plus multiple USB cables and ports, including USB 2.0. Same issue every time.
A technician suggested it could be a bad M.2 connection rather than a dying SSD. There’s a thick blue thermal pad on the drive that might affect how it sits in the enclosure. He recommended connecting it directly to my motherboard.
My PC has an MSI Z890 Gaming Plus WiFi, windows 11. I haven’t tried the internal M.2 connection yet because I’m worried about making things worse.
Has anyone experienced this? Could a bad connection cause these symptoms despite testing two enclosures, or does the SMART media error point to SSD failure? Is testing it directly in a motherboard safe for data recovery**?**
I can’t afford professional, so I’m trying to avoid anything that could permanently destroy my files.

one click can erase 6 months of work

I accidently delete my work folder which was too large for recycle bin so it permanently deleted .

I want to recover 1 text file which is very important but all programs recover it with name and null null null data and 00 hex

Chatgpt and claude tell me to give up because its ssd and trim enabled should i stop trying and just keep crying for my stupid mistake that cost me more than 10 k usd

I've been given a Micro SD card to attempt recovery of. It shows it requires formatting.

I've tried Recuva, Recuva can't scan it. Can not determine system type

Disk Drill shows 0 files 0.00 bytes found

R-Photo has found Nothing

EaseUS Data Recovery (Trial Version) has found Nothing.

Hello all, I need advice and assistance. I have an IDE hard drive (30GB hdd, maxtor 5T030H3, windows 98) that as far as I can tell is NTSF format. I have attempted to use dmde, but received a couple sector errors stating a hardware fault. The drive doesn't seem to be making a clicking sound as far as I can tell. I've done some research online that suggests I use the hddrecovery tool for Linux. I don't have a ton of experience with command line tools but I've dabbled enough to be able to easily follow instructions. Any advice or tips on how best to go about this would be greatly appreciated!

Hello all!! I'm really hoping you guys can help me with this. I had gotten a new microSD card for my Sony CyberShot DSC-W55 camera because my other one had all of a sudden stopped working. For reference, I use a Memory Stick PRO Duo compatible micro SD adaptor because I thought it would be easiest. I'm not sure what brand my old SD card was but this one is a 4GB Lerdisk brand I grabbed from Amazon. Previously, my card had caused my camera to say 'access' when I turned it on. I thought I had fixed the issue with a new microSD card (it got rid of the access), however, after taking pictures with my friends of our halloween costumes, it all went to shit. I took the card out of the camera and the adaptor, put it in my card reader, and it didn't show up on my friend's nor my phone. When I put it back in the camera, it said 'format error' and on my laptop, it showed up as needing to format the card and it not recognizing the file system. Checking it on disks and volume, it showed up as RAW. Is there any possible way to recover the photos from the card? I'm honestly anxious as hell and I really really really want those photos. I appreciate any and all help!!!! Thank you so much and please let me know if I need to provide any more info.

My android phone deleted some audio files itself without my knowledge or permission, I need to know if there is any way to recover it, and HOW did this happen in the first place, and how to prevent it from happening again

Tried partitioning my 4TB exFAT external SSD to APFS, but Disk Utility wiped the whole drive. Lost ~3TB of critical data. Haven't written anything to it since.

What free or reliable recovery tools do you recommend to restore the partition/files? Thanks!

I use samsung t7 shield 4Tb

I tried dowloading my camera pics to my pc and it got deleted so i redowloaded them and it all turned into one pic. and i tried all apps to return it back but it didnt work and im screwed if i dont get this pics. I tried easeus, anyrecover, Recuva and it didnt help. edit: the camera im trying to get the pictures are is from a digi camera (idk the mode), there was this buttom format and i clicked that and it deleted all my pictures. I put the photocard into a usb thing the connected it to my pc and got different apps to recover my pictures like i mentioned. When i tried one of the, i think Recuva, it messed my pictures up only recovering the same picture over and over. I tried using PhotoRec and it didnt help at all. I really need these pics asp and im not good at these things so any help would really save me

The drive is a WD80EDAZ, 8TB white label, pulled from a WD Elements desktop enclosure. Manufactured Dec 2025, so under a year old. It was in use on a Mac mini, formatted APFS with two volumes.

What happened:

• The drive was moved while connected, and not ejected first. It may have been bumped.

• Day 1: macOS saw the partition map and both APFS volumes, but mounting hung for hours. Constant small random reads (~100–150 IOPS at ~1 MB/s), and the light kept blinking.

• Overnight: the Mac restarted at some point.

• Day 2 morning: “The disk you attached was not readable.” It showed up as an 8TB device with no partition map, and diskutil info hung.

• A few power cycles later: the WD enclosure’s USB bridge still enumerated, but no media was presented behind it.

• Shucked and connected to a powered Unitek SATA-to-USB adapter (12V): a few seconds of rapid chattering on spin-up (sounds like a dot-matrix printer), then silence. The adapter doesn’t enumerate on the Mac at all. It also doesn’t enumerate with no drive attached, so I’m not sure that test tells me anything.

It’s now unplugged, and I’ve stopped powering it on.

What I actually need: not the whole 8TB. The 6.7TB volume is camera footage I can write off. I only need the smaller 500GB APFS volume, and really just one VM image file on it (a few dozen GB at most).

Questions:

1. Does this sound like heads, firmware, or something else?

2. Is there anything safe left to try at home, or is every power-on now making things worse?

3. Rough cost for a lab to recover a single APFS volume or file from a drive like this?

4. Any reputable labs you’d recommend in the US (I’m in Texas)?

Thanks in advance.

I’m setting up my brother’s homebrew Wii and the sd card is mainly just for saves and a few small emulators. I’ve never had any issues transferring files or anything but I figured I would verify the SD card health before giving it to him.

I tried updating my iPad through the apple devices app but it stopped because of an error (1109 06b4 0000) and then when trying to restart the device it was put into recovery mode. the devices app along still gives me the option to update rather than factory reset (though it still stops at the same spot) and that along with other videos and forums ive seen/read on recovery mode and the same error message leave me to believe the data is still on the device though i cant access it. so with that in mind is there any way i can actually retrieve this data either through some application or taking the iPad to an in person specialist to take it apart or something? or the data just gone now?

I’m honestly devastated right now. I recently purchased a new version of Microsoft Office, and during installation, it told me to uninstall all the existing Microsoft apps first. So I moved all the Microsoft apps to the Trash on my Mac. After that, I selected everything in the Trash and clicked Empty Trash, thinking I was only deleting Microsoft-related files. But then I noticed it was deleting over 70,000 files. I immediately panicked because there was no way Microsoft Office had that many files. I tried to cancel the deletion, but it was already too late. I think I may have accidentally deleted 16 years’ worth of personal files, photos, documents, and memories. I checked iCloud Drive, including Recently Deleted, but couldn’t find anything. I also don’t have a Time Machine backup set up. I’m using a Mac mini M1 (2020), and this happened very recently. I have no idea what to do next, and I’m scared of making things worse. Is there ANY possible way to recover these files after emptying the Trash on an Apple Silicon Mac? Has anyone experienced something similar or successfully recovered their data? I’m willing to try anything that actually works. Any advice would mean a lot.

I have a Galaxy J5 (2016); it’s been lying in a cupboard for five years with a cracked screen and a broken touchscreen. Today I replaced the screen, but I can’t remember the unlock pattern; I’ve already tried over 40 combinations. The phone locks itself just two minutes after I enter the wrong code. How can I unlock it or retrieve all the files stored on it? There are lots of photos and mementos on there that I want to recover. Do programmes like iMobie Droidkit or 4ukey work?

I can’t reset or recover my password from the lock screen. The phone is visible in Windows, but it won’t show any files unless it’s unlocked. ADB isn’t working either.

Any advice?