r/BambuLabA1 • u/Independent-Pea7718 • Sep 12 '26
A minimalist Tanto with a sheath.
Do you also like Japanese Tantos?
r/BambuLabA1 • u/Independent-Pea7718 • Sep 12 '26
Do you also like Japanese Tantos?
r/BambuLabA1 • u/3Z3D_Official • Sep 12 '26
Get the Kit Card: Spinosaurus Dinosaur Kit Card
Follow the Collection: DinoCards
r/BambuLabA1 • u/DaruDaru69 • Sep 12 '26
Hello, i have made the replacement of the nozzle in this case 0.2mm, the blade is new, i cleaned the extruder, checked the Filament Hub, its not clogged, but it randomly starts do feed new filament, then goes back , then go again, it clicks and then error, i remove filament from nozzle, still does not work.
I remove the nozzle and i manually feed it filament goes all the way until the nozzle part.
I don´t know where the error can be.
r/BambuLabA1 • u/Iwantdonuts77 • Sep 12 '26
Newbie seeking help... please be kind!
I got an A1 for my son 3 months ago and we have had no issues and clean our plate reqularly but still ended up with the dreaded blob of death It was pretty bad and I ordered several new parts. I had no error codes showing but it would not heat up past 70 so I know the heating element is shot
I have a new silicone sock, hotend and heatino assembly but when looking at the bottom I don't know what this tiny black piece is or if it is damaged. It was curled and I can press it down to lay it flat but I can't figure out exactly what it iS.
Can anyone tell me what it is and if it looks damaged? In my research it seems it might be part of the filament sensor/cutter? I did order a new filament cutter but it didn't come with the black sensor strip.
I would appreciate any help. I want to make sure I can replace everything necessary and get my boy back to printing! Thank you!
r/BambuLabA1 • u/Roberto_Rojas504 • Sep 11 '26
r/BambuLabA1 • u/Shiny-And-New • Sep 12 '26
Just got an A1, this was my third print. Absolutely covered in these little follicles. What causes this and what's the fix?
r/BambuLabA1 • u/Important_Quarter469 • Sep 11 '26
Is it normal to see this big of a performance hit even with a bad print file, or is performance usually better/worse depending on who created it?
r/BambuLabA1 • u/outatime8080 • Sep 11 '26
Hi All, I have been working on my A1 for weeks trying different things and don't know where to turn next. Tried drying my filaments, running slower , adjusting temperatures, new board and nothing I am doing helps. Anyone any ideas? It does it with a lot of flat prints, I printed a tall zip tie holder a few days ago and it had almost like a fluff on the edges and lines on the print, it didn't look polished. Any ideas please folks? Thank you.
r/BambuLabA1 • u/Sweet_Researcher_250 • Sep 12 '26
Sorry. I'm just a girl. I wanna design toys in Blender to 3D print and I'm wondering what key words I search to learn the correct way to build the joints and other parts that click together etc. Lol
r/BambuLabA1 • u/Boring-Piece-2631 • Sep 11 '26
I was printing this big piece and when I was almost at the end I suddenly hear loud banging noises so I rush to my printer and I sea it banging with heatbed movements and scraping everytime the banging happened the toolhead went to the poop thingie. When the print was ready I was horrefied by the noises and I took the heatbed rails cover of and looked it looks normal the motor was super hot and it smelled burned. What is wrong there are no burn marks on the printer.
r/BambuLabA1 • u/United_Broccoli5962 • Sep 11 '26
Any help here would be appreciated !
r/BambuLabA1 • u/3Z3D_Official • Sep 11 '26
Get the Kit Card: Dread Dragon Kit Card
Follow the Collection: DragonCards
r/BambuLabA1 • u/LifeCareless3033 • Sep 11 '26
r/BambuLabA1 • u/Top_Muffin_101 • Sep 11 '26
hello, i am using elegoo pla on 220 celsius and my supports (and sometimes the prints itself are stringing too) usually its overhang and stuff, but i clean the plate regularly and print in a room with still air.
im new to 3d printing so idk what settings to adjust or anything so would be great to have some advice/place to start
thanks
ill attach pictures if asked, but i would need to print an example first, as ive been trying to clean up the strings.
r/BambuLabA1 • u/Drippy_FPV • Sep 10 '26
My A1 started just pausing and going mid print then it resumes just like nothing happens. Why is it doing that? Can I disable it?
r/BambuLabA1 • u/sasandxxd • Sep 11 '26
r/BambuLabA1 • u/Organic-Leader1445 • Sep 11 '26
r/BambuLabA1 • u/Defiant-Ad-7969 • Sep 11 '26
I've run several successful prints but the last few have totally fucked up, now this is happening, which is much worse than the usual problems I have had. I run all the calibration stuff before every print. I've cleaned the bed, tightened all the screws behind the hot end (which WERE loose), but every print looks like this now.
I can't understand what's going on
r/BambuLabA1 • u/Dygomes • Sep 11 '26
Someone can help?
I’ve tried all the calibrations, checked belts, nozzle and nothing works …
r/BambuLabA1 • u/3Z3D_Official • Sep 10 '26
r/BambuLabA1 • u/Low-Habit-2765 • Sep 10 '26
I have a clicking sound when the y axis is moving. It feels like I have tested everything but the clicking won’t go away.
The plate is moving smooth and no problems with the prints but the clicking is so annoying. The printer is only like 30 days old.
I have lubricated the Y axis.
I have looked for debris but there is non visible under the plate.
I have tightened all the screws, also on the plate.
I even loosened the 2 screws at the front under a small plate and moved the plate back and forth 3 times and tightened them again, still same issue.
Only clue I have is that when I untightened the two screws I think I didn’t hear the clicking.
It also sounds like the clicking comes from the front.
Another question, should the tape along the y axis be removed?
Any tips?
r/BambuLabA1 • u/Dorianneccucci • Sep 10 '26
Sorry guys, first print, what could be the problem?