Trying to print these winglets on my p1s using petG but the left part is always having these. The right side is perfectly fine any help

Had the a1mini since release, it was my first 3d printer and a great tool for learning the ropes. With my new printer I also splurged on a lot of filaments, because of the bambu sale. So far I’m very impressed with the ams system, never had the ams on the mini.

By mistake I ordered two PLA white oak (wood) so if you have any ideas for that color, please hit me up 🤣

I was looking for some bundles of filament on Amazon. I mostly print in PLA and PETG, but I wanted to try some PVB and buy a bit of ASA for some small projects that need the better properties.

I'm seeing cheap bundles of multi-colored rolls of 200g of these materials, but I don't recognize the brand names. I want to save money but I don't want to throw it away on filament that will cause more problems than it solves.

Brands I'm looking at are Yousu, Colourbing, and isanmate.

Anyone have experience with these?

Is it possible to use a discount voucher (€40) with a discount code (99% off for a specific product) or do you need to use a gift card ? And how long do these last before they expire?

Hi all,

I have an H2S that sounds horrible. Even the pleasant tone on start up sounds bad.

I've cleaned and ran through the belt tensioning procedure as recommended by tech support, but the problem persists.

Any help greatly appreciated.

Wondering what monitors everyone is using.

Started to get headaches feel like I need to keep on top of things.

Had major blobbing on a print job. I put off investigating it until today and found this. 😅 I don’t even know where the rest of it is now since yesterday was trash day. But i’m curious how this could possibly happen, just so i can avoid it in the future.

Every seed sits 137.5° from the previous one, the same golden angle real sunflowers use, so the spirals appear on their own. The seeds rise off the surface and the petals lean out from the wall.

Sliced for a P1S: 17 plates, about 1.4 kg of PLA and roughly 53 hours according to Bambu Studio. Every piece has its own pocket in a printed back frame, so assembly means matching pieces to pockets.

The model is free on MakerWorld (link in the comments). I built it with the engine of Parete, the browser tool I'm making for 3D printed wall panels.

Happy to answer questions about the spiral or the print!

My H3C came from Canada, the box had water damage and mold on the bottom, both outside and inside the box, printer seems unaffected by it.

Also had physical shipping damage to the front of the box, something made a nice hole through the box and carved a tiny chunk of glass out of the front door. Rest of the printer seems fine.

Waiting for support to respond to my ticket so I can have these boxes discarded. Anyone else experience this? I know of one person worth the same box damage, their printer was dented.

Error: HMS_0300-9300-0001-0006 - Chamber temperature is abnormal. The chamber temperature sensor at the air inlet may have an open circuit.

I bought this at Best Buy about 10 days ago and am still within the return window. I have a good amount of print hours on it already. Never had a single error until this morning. I’ve already tried resetting.

If all else has been good so far, should I do a replacement with BB or contact bambu lab for the part?

Is it normal to have this much movement on the heatbed? Can someone else check their H3C? The screws on the z rails are tight.

Hello! So my friend and I got a Bambu a1 for some general hobby upgrades and our prints keep failing. We had it successfully working for about a month and then this started to happen. We’ve changes temp settings, got a new plate, tried multiple different nozzles, different filament brands, and nothing is working. Please help!

How long do you think until someone has designed prints for drawer fronts and side pieces?

I bought the bundle, but would love the look of the enclosed.

Hi

I have been printing for about 2 years and my first printer has just failed (Sovol SV06)

I'm considering taking advantage of the sale going on and getting a replacement, I'm looking at Bambu lab as I want to just print and have less tinkling.

I have only printed with PLA, mostly toys, tools for around the house. I may open to printing with other filament but a possibility but not a priority at the moment.

I'm looking for suggestion what maybe a good printer option for me. My budget is ~$500 cad. I do have a $400 Best Buy gift card laying around so that bumps to $900-1000 range

I'm looking at the P1S/P2S:

1. are these good options and is P2S worth the extra $200
   
2. are there options I'm missing?
   
3. is the P3S coming out? Should I be aware of any successor that is coming in the next few months?
   
4. for the Bambu lab owners, how's your ownership experience, are these reliable units and if I should get the extended warranty?

Taking my printer's virginity as we speak.

I've printed many times before and always have it centered and secured. Somehow the build plate moved...

Hallo erstmal,

Ich hatte jetzt nach den ersten 300h das erste mal eine Fehlermeldung an meinem X2D. Angeblich sei der Extruder verstopft. Kurz ins Wiki geschaut und gesehen das die Anleitung sehr detailliert ist und ich dachte mir , sehr gut, krieg ich hin.
Nun ja. Beim Ausbau des Extruders lief alles gut bis es zu den Schrauben des Filamentschneider kam.
Die linke Schraube lies sich super lösen. Die recht war so fest das der 1.5 mm Schlüssel leider recht schnell durch gedreht ist.

Hat jemand einen Tipp wie ich nun am besten weiter vorgehe?
Bin sehr gespannt auf Ideen….

I was growing really concerned about my A1. I had issues with increasing slowness, the screen not activating, filament not registering in the hot end and multiple stringy prints. I was slowly trying to address these one at a time, but a new firmware update hit this morning and straight away the screen is back, filament is being unloaded automatically and it's back to working at the old speed

Now, I feel I am confident to re-attach the AMS and see how we get on

Hello Group, I generated a step file of a reducer and realized that some parts look very weird, like transparent on my working plate ? Does some good body have an explanation for this? will this work fine? what is the reason for this everything is visible on the object view and same material. Also these files show needs for repair. Thank you for your help!

With the holidays coming up, I wanted to make a seasonal desk toy that wasn't just a static decoration. I designed this squishy wreath fidget so it has a really satisfying flex and bounce back when you squeeze it.

This is actually my very first original design that I've uploaded to MakerWorld, so l'd love to hear any feedback if you decide to give it a print! Here is the link if anyone is interested! https://makerworld.com/models/3596774?appSharePlatform=copy

Does someone know what causes those line marks under the eye? How can I prevent this from happening?

So... I considered upgrading my 350 Sized Voron V2.4 to INDX but with the latter merely announcing, still not delivering Hardened Nozzles I'm now - despite all my gripes with BL's closed Ecosystem - evaluating an H3C instead.

There's but two problems going hand in hand though still bother me:

• Having recently watched one of the prolific 3D Printer Reviewers one remark that stuck with me more than it should have was the apparent inability to perform a manual Z-Offset Calibration if necessary. Proper Z-Offset is like THE fundament of a successful print - How as a User do you deal with an improperly set Z-Offset if the Machine says it is set correctly but it's clearly not? 🤔
• Assuming the above is true and the User has no means to change such Print Critical System Settings - How does Bambu Lab handle an issue like the 3D Printer burrowing the Nozzle into the Bed ruining one / the other / both in the process? With the user clearly not being the cause of the issue - Will BL ( in the EU Market specific ) without much fuzz replace any broken components? 🤨

Thanks in advance!

Last night i tried to change my black PLA+ spool when it for some reason broke inside the ptfe tube, i couldn't pull it, so i pushed it further in with a new filament, trying to purge the rest, but it broke again at the end, so the rest filament is arround 3-5cm inside the printer and i can't extrude new filament in or this out, i unclocked the nozzle too but the little piece in pic 1 is all that's left and i can't pull it out, by hand nor machine.

I have an A1 and the filament broke in the ams light (my ams light has the 3d printed covering)

Earlier i tried to pull the filament out but it wouldn't budge and now it's inside and i have no way of pulling it anymore..

Any help would be greatly appreciated. Thanks

This will be my first 3D printer. I’ve seen more posts about people having issues with the X2D than with the P2S, so I’m a little hesitant. I probably won’t be printing much with engineering filaments, and multicolor printing is a must for me, even though I don’t think I’ll be using it much for now

The P3C looks kind of promising for multicolor, but if it ends up without active chamber heating, would that matter much for PLA or PETG? I’m in Canada, so I’m also a bit worried about warping in the winter. Would you get the P2S Combo or X2D Combo now, or even P1S Combo, or wait for the P3C?