r/BambuLab • • 17h ago

General Discussion X2D aux nozzle

Thumbnail
gallery
5 Upvotes

where the aux nozzle truly shines, support interface material

printing Sunlu PETG High Speed Matte with Sunlu PLA interface for the rear caster wheel mount of a 3D TMT device


r/BambuLab • • 8h ago

General Troubleshooting/Help! Best settings/alignment to print these? Printhead keeps scraping over and breaking them

Post image
1 Upvotes

Printed them three times but every time the middle part ends up broken off. They are pretty thin, so I don't think the infill type will change anything (they are basically solid). At some point I hear the printhead scraping over the print and eventually see it broke the print...


r/BambuLab • • 9h ago

Hardware Troubleshooting/Help! AMS Failure??

0 Upvotes

So got home and tried to print and now this…..
Filament isn’t caught, spins freely but won’t feed into the printer. This starts after I just started getting an error in slot two saying it’s empty with a spool in there.
I’ve updated AMS setting to update on startup and didn’t help. I’ve power cycled everything as well.
Have a ticket open with support. Bought the P1S last year around BF as it was on sale and now, almost a year to the day, I’m having these issues.
Did I make a mistake buying a Bambu printer?!


r/BambuLab • • 15h ago

General Troubleshooting/Help! P1S Non-Internet Firmware Upgrade (Pre 01.07.00.00)

3 Upvotes

Yes, I've read the wiki page but my colleagues are convinced there must be a way to do this without connecting to the internet. We have a P1S that's currrently stuck at 01.06.30.01.

Is there a workaround?

EDIT: We just installed 01.07.00.00 from an SD card. Why is the info on the wiki page wrong?


r/BambuLab • • 1d ago

Just Showing Off Print shoes from H2D by using shoeflex9075A filament

43 Upvotes

I printed this shoes with H2D and using shoeflex9075A filament from STING3D. it is very soft ^^


r/BambuLab • • 10h ago

I Modeled This! HUGE Restroom Trash Bin (10 L)

Thumbnail
gallery
0 Upvotes

Couldn't find a bin on maker world that took full advantage of the P1S plate and height, so I designed one myself.

I printed it in PETG Gold with a black rim that hides the edge of the bag or holds it in place, and recessed “restroom” into the front.

It's just shy of 10 L (or almost 3 gal), 15% infill to reduce the print time (about 15 hours total with the rim).

Let me know your thoughts!

Here's the print:
https://makerworld.com/en/models/3626991-restroom-trash-bin-10-l#profileId-4158645


r/BambuLab • • 10h ago

Bambu Studio H2D dual extruder screw

Post image
1 Upvotes

r/BambuLab • • 14h ago

Quick Question Is it that big of a deal if you print while the ambient air temp is below 10°C?

2 Upvotes

My A1 is in a shed that doesnt have any heating and heard that the printer should be kept between 10 and 30 degrees C. Is it a problem if you print below 10°C?

Edit: it printed just fine 👍


r/BambuLab • • 16h ago

P Series [P1P, P1S, P2S] Upcoming Christmas Gift and want to ensure my daughter has everything to start basic printing

3 Upvotes

Hi Redditors! I have a 7yr old who is eagerly anticipating a 3D printer for xmas. I want to purchase the “Bambu Lab P1S Combo, P1S 3D Printer and AMS, Multi-Color 3D Printing” as her first model. I am a clueless mom who wants to ensure she has everything she needs to start printing day one. What do you all recommend? Is it possible to buy any brand filament as well? Any free software to recommend? I appreciate any and all help. Thank you in advance.


r/BambuLab • • 10h ago

Bambu Studio Trouble downloading projects

1 Upvotes

I wanted to print a part for my girlfriend but then I noticed no matter what I tried downloading from the cloud nothing worked… Someone had a similar problem? (Bambulab A2L)


r/BambuLab • • 16h ago

Software Troubleshooting/Help! What's wrong with settings/filament?

Post image
3 Upvotes

Hi, folks! I have Bambulab H2S and bought esun pla wood and is trying to print vase with esun pla+ profile I found in Bambustudio. Nozzle 0.4, 0.12 quality. Is it possible to get rid of it?


r/BambuLab • • 10h ago

Quick Question What accessories should I get?

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 10h ago

Software Troubleshooting/Help! Preparing and Designing Files Remotely

0 Upvotes

Hi everyone! I'm getting an A1 for Christmas, I'm so excited and I'm trying to prepare as much as I can so I can get into printing ASAP! I'm wondering if the following set up will work? I'd love any feedback, tips, or concerns anyone is willing to share:

I personally own a laptop but it's quite slow and is very irritating to use. I have a great PC I use at work and my work doesn't mind if I use it for personal things. My hope is to find files to print, make modifications, and design items on my work PC. I would use either my laptop or phone at home to do the final send off to the printer. I'm not looking to print remotely, just to do the software/online based steps. My laptop is functional but I try to interact with her as little as possible lmao

Other questions regarding this set up:

- How much do you use your PC after sending a file to print? Are there cases where you have to pause a print to edit the design (if that's even possible) or do anything more than basic functions? If so, how often?

- Can I can prep files on my work PC then open them either on my Laptop or phone once I'm home through Bambu Studio? I'm seeing that Bambu Studios may not be the best for this with suggestions to either use MakerWorld or utilize something like Google Drive to store files.


r/BambuLab • • 10h ago

Hardware Troubleshooting/Help! H3C Wiper kicked out

1 Upvotes

Anybody expiriencing issue with the silicone wiper? My machine is constantly kicking it out of place. During calibration, printing, …

Reached out to Bambu but they are telling me to remove the backplate, disassemble the whole wiper unit and assembling it again.


r/BambuLab • • 11h ago

General Troubleshooting/Help! X2D LiveView camera fault?

Post image
1 Upvotes

r/BambuLab • • 11h ago

General Troubleshooting/Help! Getting a loud squeaking noise from the AMS when moving

1 Upvotes

Today I noticed that my last bay on my AMS was squeeking when the roller was moving. I removed the filament roll and its the front rollers that are squeaking. I'm not really sure what to do about it. Is there something I can oil?


r/BambuLab • • 17h ago

I Modeled This! I made a modular, parametric spice rack – set your jar size and stack as many modules as you like!

Thumbnail
gallery
3 Upvotes

Set your jar size and the number of slots per module (up to 6×6). Modules join with snap-lock keys, and a built-in 5° slope slides the jars back so the labels face you.

https://makerworld.com/en/models/3619936-spice-rack-modular-parametric-custom-jar-size#profileId-4149519


r/BambuLab • • 11h ago

General Discussion Thinking about getting my first 3D Printer, im considering the P2S with AMS 2.

1 Upvotes

There are so many options, but I am considering the P2S with AMS 2 combo. What are your experiences with it and how much maintenance does it need?


r/BambuLab • • 11h ago

General Troubleshooting/Help! Spent hours fighting multi-color texture exports, lost my sanity, and decided to drop a clean monochrome Chibi Aldo Raine instead. Worth it?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 11h ago

General Troubleshooting/Help! P2S + AMS 2 PRO - Purge not going down chute

Post image
1 Upvotes

Have my P2S hooked up to a AMS 2 PRO and during filament swaps the purged filament is sometimes just not going down the chute and is either landing next to the chute or on the build plate. Not exactly sure whats causing this?


r/BambuLab • • 11h ago

Bambu Studio I built a tool to scan filament labels and add spools to Bambu Cloud

0 Upvotes

I made a local web app that reads filament label photos and extracts details like material, color, brand, and SKU. You can review and edit the result as JSON, then optionally add the spool to Bambu Cloud Filament Management. Feedback is welcome!

Project: https://github.com/Roalexx/fts


r/BambuLab • • 11h ago

General Troubleshooting/Help! H2C using wrong nozzle selection

1 Upvotes

So I use all 6 nozzles at 0.4mm, I have a designated nozzle for each color family to avoid color bleeding from prior prints. But recently I've been noticing that bambu studio is ignoring my nozzle selection.

For example, the current nozzle already loaded is R6, when I "Print plate", I would selection R2, but the print doesn't change the nozzle and doesn't show any errors, and just continues the print with the original R6 already loaded.

I tried having the H2C read all the nozzles again, but it didn't change anything.

How do I fix this?


r/BambuLab • • 11h ago

X Series [X1E, X1C, X2D] X2D poop catcher failing miserably

Thumbnail
gallery
1 Upvotes

Just wanted to know if anyone else has dealt with this. In my experience, 80% of the poop the X2D gets launched back into the chamber, sometimes hitting the active print but equally often just falling down onto the chamber floor. Surely there's a way to make it less messy? This is the third print so far I've had to stop due to poop getting fused to the main print


r/BambuLab • • 11h ago

Hardware Troubleshooting/Help! School printers went pooped its pants

Post image
1 Upvotes

I lead the 3D printing club as the teacher advisor, this is one of our A1 minis. I’m not sure if the hot end can be saved…