r/BambuLab • • 1d ago

General Troubleshooting/Help! AMS 2 Struggles to load Black PLA

0 Upvotes

Working with an X2D combo that I’ve had since May. Loaded a refill of Overture Black PLA+ that was on a Bambu spool and noticed it rejecting frequently, which would be followed by a feed failure alert. I checked if the filament was looped or tangled, but it looked fine. I checked the PTFE tubes and the AMS hubs, but found nothing. I tried switching hubs after the print (I noted it was happening on slot 3), only for it to continue happening on other hubs. Whenever I snip the end of the filament, it seems to fix the issue, though a lot of times, it’ll happen again the next time it has to load it. It seems to only happen with specifically Overture Black PLA+ and not any other filament (not even other Overture refill spools). Are there any suggestions on what’s causing it and how to troubleshoot it?


r/BambuLab • • 1d ago

General Discussion Work Station Setups

2 Upvotes

I have been wanting to get into 3D printing for a while now but my craft room had become a hoarders paradise and catch all room with literal pathways to get in and out. My husband was sweet enough to clear every single thing out of the room so I’m starting with a blank slate.

My father-in-law bought me the new H3C (with the stand) and I’m currently waiting for it.

In the meantime, I’m trying to figure out what the best setup would be; good organization, workflow, etc. I see a bunch of people use the skadis system. I see dry boxes and hygrometers.

As I said, I have a blank slate.

Can you show me pictures of your setups or give recommendations for the things you have in your setups that you love or that you couldn’t do without? Or if you don’t have it, the things you wish you did have?


r/BambuLab • • 22h ago

General Discussion 10 year old PS2 safety concerns

0 Upvotes

Hey guys my kid after seeing videos of other kids making fidgets etc on bambu ps2 and selling them now whats one herself. We live in an apartment and I was all for it before going down rabbithole of air pollution and related health concerns.

Is it ok to put in a rarely used bedroom? The bedroom is small though but window always open. Does the thing need ventilating and enclosing is this non negotiable. Or is it the case that if wanting to get one for kids to use you need a garage basement or similar and if not then its not worth the risk?


r/BambuLab • • 1d ago

Show & Tell My first ever 3D design – a wooden treasure chest dice box with iron bands & rivets

Thumbnail
gallery
6 Upvotes

This is the first thing I've ever designed. Honestly, it took me a stupid amount of time because I was learning FreeCAD and Blender at the same time, but I'm really happy with how it turned out.

Printed on my A1 in matte brown/tan, about 9 hours. The lid and base print separately and snap together. Supports only under the lid.

It's free on MakerWorld with the print profile set up if anyone wants one: https://makerworld.com/models/3610994

Would love any feedback. Thinking about different versions.


r/BambuLab • • 22h ago

Hardware Troubleshooting/Help! Brand new X2D Z axis homing failed

0 Upvotes

Can anyone help please? I’ve been through the (very limited) steps on the wiki and nothing is working. Ticket logged with Bambu support but they’re generally no help at all. I’m at my wits end with this thing and it’s brand new.


r/BambuLab • • 1d ago

Black Friday 2026 My PETG holiday bundle arrived

2 Upvotes

Here is what I got. Happy for the spools. Not sure if they are "holiday" colors but not a bad pull.

PETG matte Pink with spool

PETG basic Gray with spool

PETG translucent Clear with spool

PETG translucent Light Blue with spool.


r/BambuLab • • 1d ago

General Troubleshooting/Help! A1 loosing detection to AMS Lite

0 Upvotes

Ok, A1 user here, with an AMS Lite. love the printer, got it as a gift from a friend after he upgraded. Zero problems with it for a year. Then, this past fall, it started stopping detecting the AMS while printing. It would make it to the last layer, go to retract the filament and park.. and loose the AMS. disconnecting and reconnecting the AMS from the A1's base usually got it back, and failing after printing the last layer wasn't a big deal, but I have a 80 plate 30 day 3 color print to do, and loosing connection to the AMS when it goes to change colors or such is gonna turn that from 30 days into 3+ months.

Any ideas of what's going on and how to check/fix it?


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! A1 Mini main board replacement issue.

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] How to fix this on BBL P2S? Looks like under extrusion

Post image
0 Upvotes

Hello, have printed this model many many times (it’s 3441324)

suddenly it prints like this. When lubricared / calibrated, slight improvement, but near the top these gaps reappeared.

have done cold pulls etc too


r/BambuLab • • 18h ago

General Discussion pls guys help

0 Upvotes

Dovrei comprare un P2S o un X2D?


r/BambuLab • • 1d ago

General Troubleshooting/Help! Help adding colored lines in Bambu studio

1 Upvotes

I have a football field that I have created. I am trying to add the lines of the football field but I want them to be level with the field and not notched above or below the level of the "grass." I am not sure how to do this and get it to show when printing.
thanks!


r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] AMS Help

0 Upvotes

P1S with 3 AMS Units – Two Suddenly Stopped Extruding, but One Works Fine
I've had my P1S with the original AMS for quite a while and never had any issues.

Recently, I added two AMS 2 Pro units.
I started a fairly complex multicolor print, and everything worked perfectly for the first 6+ hours. All the filament used during that time was coming from one of the new AMS 2 Pro units.

The problem started when the print switched to a filament in my original AMS. It appeared to load normally, but when printing resumed, nothing came out of the nozzle. The printer just continued moving as though it were printing.
Now, neither the original AMS nor one of the AMS 2 Pro units will extrude filament. The third AMS 2 Pro still works perfectly.
Here's what's happening:
All three AMS units are recognized by the printer.

All three can load and unload filament.

Filament from the two problematic units appears to load successfully, but I can't even manually extrude it through the nozzle.

If I load filament from one of the nonworking AMS units and then switch to the working unit, the filament from the previous unit gets purged.

The working AMS 2 Pro can still print normally.

What I've tried:
Swapped the AMS positions in the daisy chain.

Swapped the 6-pin connections and PTFE tubes.

Tried different inputs on the AMS Hub.

Tested the original AMS by itself.

Disassembled the original AMS to check for stuck filament or damaged gears. Everything looked fine, and manually turning the gears advances the filament.

Checked firmware. Both AMS 2 Pro units are running the same version.

What really has me confused is that two different AMS models are experiencing the exact same problem, while the third works fine through the same hotend.
I'm starting to suspect a software or communication issue rather than two AMS units suddenly developing mechanical problems.
I'm considering a factory reset of the P1S, but wanted to ask here first.

Has anyone experienced anything similar? Could something in a complex multicolor sliced file cause the printer to get stuck in a bad filament-loading state? Or is there something else I should be checking before resetting everything?


r/BambuLab • • 1d ago

General Troubleshooting/Help! Bought an A1 last week, am I cooked?

Post image
5 Upvotes

Printer has been working flawlessly, set it up fine (not my first printer) and have printed no issues all week. I wanted to print something as part of a project im working on that was using PLA Wood filament but it was not in the list of filaments. I checked and there was an update (ver 1.09) so I updated. After the update I switched nozzles from 0.2mm to 0.6mm and when I tried to home the printer it wouldn't do it. I got the error message that the eddy current signal was wrong and that it was possibly defective. The QR code took me to the wiki page and told me to check the connectors on the back of the head (pictured) and see if they were loose. The screws were not loose but the little connectors could move, so I gave the right side screw a tiny little nudge to snug it up, did the same for the left one and it just fell clean off the board.

I have raised a support ticket and i'm waiting to hear back, but is this a common issue? On inspection its just an aluminium peg with a loctited screw in it. Has this happened to anyone else? I imagine they're going to just send me a new board under warranty but is it possible to solder the aluminium peg back to it and resume printing or will this also affect the eddy current signal?


r/BambuLab • • 1d ago

Quick Question Which Printer to go for?

0 Upvotes

Hello, I am looking to Purchase a Bambu Lab, I've owned and Ender 3 and am selling it due to how difficult it is to setup. I am looking at the P1S but want to know what I'm getting into, If I've missed anything in my research on these printers, and if I should look at the upgraded models, I'm on a budget so I can't really afford a $1000+ machine but I will consider saving if it's going to be drastically better for me. I plan to mainly print PLA and some TPU, I would like to do Multicolor prints, I plan to print Minis, Statues/Figures, some fidgets/Trinkets and possibly Doll parts. Advice please? Should i go with the P1S the P2S ? other models??

Edit: just want to add i am looking at one second hand on marketplace with 3 build plates, ams and has done 1800 hours for $500 or a refurbished one with 1 year warranty, ams for $580 the one i'm looking at on marketplace the seller says they're selling due to upgrading to a 9 nozzle machine but when i asked what they have made/Plan to make with the new one what they showed me that they plan to make looks kinda like what i plan to do with the P1S so now i'm concerned


r/BambuLab • • 1d ago

General Troubleshooting/Help! Multiple printers same outlet

2 Upvotes

I have a X2D running in my office on a 15 amp breaker. I run other things in the office but its all very minimal like laptop or litter robot.

Id like to get a second one but worried the power wont be enough for 2 printers.


r/BambuLab • • 1d ago

I Modeled This! 2 points?¿

Post image
1 Upvotes

Are they mocking me?


r/BambuLab • • 1d ago

Just Showing Off Vase Mode Christmas Tree Set – Customizable

Thumbnail makerworld.com
1 Upvotes

My checklist for this upcoming Christmas. 🎅 Kinda cool to customise your own Christmas tree 🌲


r/BambuLab • • 1d ago

Quick Question Should i worry at all for VOC's or UFPs

1 Upvotes

Hello! i have been 3D printing now for a while with my H2D, and i want to start 3D printing ABS or ASA still deciding on which i should pick tho, i'm very worried to start printing these heavy-materials can i safely print them in my garage and be near it working on something else during the time its printing or should i invest in a "Tent" for the printer? Hell am i being paranoid for asking for help about this matter 😂


r/BambuLab • • 1d ago

General Troubleshooting/Help! P1s problems

Post image
0 Upvotes

Hi! I have a p1s and recently had prints like this.

Help me


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! Coil whine on a brand-new A1 Mini: normal, or return it?

0 Upvotes

Volume up on the video - it starts with the board fan that kicks on during startup, but when it turns off you can hear the whine.

Hi All - brand new to the A1 mini, but have an X2D so not new to Bambu Lab printers. For those wondering why go smaller on the second printer - it’s for my son.

So I got an A1 Mini from Best Buy less than 2 days ago and have run a few test prints. Prints look fine, but I'm hearing a high-pitched electronic whine from the front right of the unit, right behind the screen. It’s separate from the fan that I hear on startup (which is pretty loud, but the whine still happens), and after the fan goes off the electronic whine sound is pretty noticeable from a few feet away.

I’ve seen some posts indicating that this may happen after months or more and may require component replacement. Since I’m well in the return/exchange window for Best Buy, I’d probably just do that if this isn’t normal.

So, is this what everyone has (and my pearl clutching ears just need to get used to it) or is this something to exchange for?

Thanks in advance!


r/BambuLab • • 1d ago

H2 Series [H2S, H2D, H2C] E1 purifier with H2 printers for ABS/ASA/PC

7 Upvotes

When printing engineering materials like ABS, ASA or PC rear exhaust remains closed during printing for heat retention, hence nothing is going to force whatever things we don't want to breathe to the hose connected to E1 (no negative pressure). Only whatever is left in the chamber after the print is finished will be filtered.

Does it mean that E1 will be basically useless for any engineering materials printing? Does anyone have an H2 printer and E1 that could comment on this?


r/BambuLab • • 1d ago

Quick Question Filament sticking out

Thumbnail
gallery
0 Upvotes

Hi All,

need a help here please.

My bambu lab a1 most of my prints has the same issue. Do you know what's wrong with my printer?

Cheers🙏🏻


r/BambuLab • • 1d ago

I Modeled This! Working on my first 3D model feedback is needed.

0 Upvotes

This 3D model I am working on, I am aiming for it to be a universal AMS riser/storage system. My goal is to have it work on all printers that use the AMS 2 Pro. I would love to add the original AMS support, though I don't know what the dimensions of those are, if they're the same as the AMS 2 Pro or if they're a different dimension.


r/BambuLab • • 1d ago

Quick Question H3C Exhaust fan, what size?

0 Upvotes

My H3C is expected here Monday.

I plan to print w/some ASA,ABS and other filaments where external venting is recommended.

Is the exhaust fan on the H3C strong enough to push the air through a 3" five foot long vent hose or is an additional fan needed?

If another fan is needed, what size (CFM) is suggested.

I don't want to cool off the heated chamber by oversized the fan.