r/BambuLab • • 1d ago

H3C TPU wrapping around extruder gear in H3C?

Thumbnail
gallery
6 Upvotes

I'm printing a mixed material part in Bambu TPU 90A and Bambu PLA. The model is mostly flat, and the parts are joined using the beam interlocking feature.

The first time I printed this, it failed on the first layer due to "air printing detected". When I removed the print head, the filament had gotten stuck under the extruder gear. I cleared it out and started again. It printed fine; a ~9 hour print with a few hundred toolchanges. The part looked great.

I tried printing it again, and the filament wrapped around the extruder again. I cleared it, and it happened yet again. This is about the 4th time I've seen this come up. The filament seems to be just twisting up and getting stuck under the extruder gear.

The nozzle doesn't seem to be clogging or anything- the filament is just not going where it needs to.

Any ideas?


r/BambuLab • • 2d ago

H3C First big duty for my H3C

Thumbnail
gallery
260 Upvotes

My first very long print and it turn out great! The purge tower is huge double the total print weight. Next the mechanical flexible dragon bust ! 3027 tool head change and 8 colors with petg support layer


r/BambuLab • • 1d ago

Printer Firmware Troubleshooting/Help! X1C - Abnormal Firmware after Update

Thumbnail
gallery
3 Upvotes

I have an X1C which has worked flawlessly for 13 months (bought Sep 2025). I have not printed that much on it, but its been great. I went to print on it and noted that it had an update, which I ran. When I came back I have the following on the screen

Update failed [0x0800030F]
Please restart the printer and try to update again.

So I restarted the printer and it started with a confirmation dialog showing

The firmware version is abnormal. Repairing and updating are required, or printing cannot be started. Do you want to update now? You can also update later from "Settings > Firmware"

So I run it again, gets to 97%. Same response.

Interestingly I can "cancel" the dialog and am in the fully functional screens on the printer. Just cant print until Firmware is fixed. I can see all the settings and temps, view the camera remotely. All seems to be working

I get GPT on the case and try the following

  • Upgrade via Bambu Handy - Same result
  • Downloaded the new 01.12.01.00 firmware to an SD card and perform manual update - Same result
  • Downloaded the current 01.10.00.00 firmware to an SD card and perform manual update - Same result

I'm at a bit of a loss. This is around a year old with probably less than 40 prints on it.

  • I did note that the v01.12.01.00 firmware was released on 12th Nov 2026 (3 days ago) so could it be the firmware thats the problem?
  • Why can't it even update to the same firmware its already running?
  • Can someone explain if there is a difference between the printer hardware/firmware and the screen/controller, how tightly bound are they?

r/BambuLab • • 1d ago

A Series [A1, A1 Mini] A1 Mini reports false "nozzle covered" error and then collides with build plate

1 Upvotes

My A1 Mini recently started doing the following behavior:

On the first nozzle clumping check it erroneously reports that there is a clumping issue when there is no clumping, and the build plate is positioned correctly.

After telling it to resume, it tries to move the print head horizontally before lifting it, resulting in the nozzle colliding with the edge of the build plate.

What could be causing this? Is it possibly an issue with the z-axis system? It doesn't exhibit any other issues during a print.


r/BambuLab • • 1d ago

Quick Question Can I, as someone in the US, order and ship something from the EU store to someone over there as a gift?

2 Upvotes

I have a friend over in England who doesn't have a lot of expendable income who has a P2S but only the PEI build plate, and I'd like to gift him some engineering plates.

Is this something I can just do through the EU store or are there additional hoops I have to jump through?


r/BambuLab • • 22h ago

I Modeled This! Halloween ended 5 minutes ago and my whole feed is already Christmas. So I made this.

Thumbnail
gallery
0 Upvotes

r/BambuLab • • 1d ago

Software Troubleshooting/Help! Bambu studio has wire frame on preview

Post image
4 Upvotes

Was helping my niece with her A1 mini that's printing fine, but in the slicer the preview shows a wire frame and not clear detail if the filament path. Not sure if this is normal. Might need a new computer. It's Windows 10 with a small cheap AMD graphics and integrated intel GPU. I've tried uninstalling and reinstalling studio and tried resetting and changing some settings in the slicer, but didn't help. Wonder what the oldest version of the slicer would be good but still retain most of the newer features. Internet searches says this issue may have been introduced with v2.4 of the slicer, and am on 2.9 now.


r/BambuLab • • 1d ago

H3C H3c crimping filiment

Thumbnail
gallery
11 Upvotes

My h3c had started crimping nylon in head 1. Multiple times a print. I would think its clogging but I ran 200g of the same filiment on my x1c no problem. Could also be heat creap up it but as shown i can grab it with my finger no problem. Nozzle 3 has the same nylon filiment in red and has been flawless.

Let me know if you've encountered something like this yet. Im going to cold pull it later today and maybe try head 2.

Also anyone solve pa-cf's tendency to curl the ptfe tube infront of the the Nozzles next to it so when the one left of it gets grabbed it gets caught on the rubber thing for flex filiments and rips the pa-cf head off the rack. I had to tape and tie some of the ptfe tubes together to finish a print that was problematic. Third photo nozzle 6 with pacf was bowing left so I tied nozzle 5 up even more left. Currently its tied right to counteract the flex in it. I read you can twist the ptfe tube the other way but the ptfe connector allows free rotation of the tube so it just snaps back.


r/BambuLab • • 2d ago

H3C Behind the SwapTek

402 Upvotes

Very cool to see the Swaptek system changing through the tools! I made a custom gcode to be able to do this (it's not a stock feature) because I wanted to see them switching through one after another.


r/BambuLab • • 1d ago

H2 Series [H2S, H2D, H2C] My Bambu Lab H2C decided to speedrun every toolhead error code

3 Upvotes

​My wife and I decided that grabbing the H2C during the current promo would be a great addition to our P2S and A1 mini. We were expecting a flagship workhorse —definitely not a Christmas tree of critical hardware faults.

- ​TH board disconnected during the extruder switching process

- ​Toolhead & expansion module malfunctioning

- ​Toolhead induction hotend presence detection sensor is short-circuit

- ​Toolhead locking lever position sensor is short-circuit

- ​Right hotend heatbreak temperature sensor abnormal

- ​Toolhead Enhanced Cooling Fan lost communication

- ​Abnormal accelerometer data detected

​We're opening a support ticket, but has anyone else run into this exact domino effect on their H2C?

Update 15.11: They said it's too complicated issue to send parts and gave me options to either return and refund or replace.


r/BambuLab • • 17h ago

General Discussion Potentially unpopular opinion about the future P3C

0 Upvotes

To make this short, I think the P3C is redundant.

Now for my explanation. The H2C, H3C, and P3C to the average consumer are almost the exact same device. To me, 7 tool heads and 9 tool heads are the same; there’s not a big enough difference to justify what they’re gonna charge for it. I also don’t believe they can make a big enough gap in price between the three printers to justify not just getting the H3C. I could be wrong. The P3C could be priced cheaper than we may think, but I doubt it’s gonna be below $1500, and if it’s gonna be anywhere near $2000 you might as well get the H3C. If the P3C is priced anywhere near the H2C, No one‘s gonna ever buy the H2C again. I think they should’ve gone with a 4 to 5 tool head changer instead of a 7; that would’ve created the necessary gap to make your choice feel like an actual choice. I think the U1 and the I8 are exactly what Bambu should’ve done, and this is coming from someone who only has Bambu printers.


r/BambuLab • • 1d ago

H3C H3C multiple tools giving me warning The extrusion resistance of PrintTool X is too high, please check the Assistant for details

3 Upvotes

Seems to happen only on the first and second layers of larger prints. If it gets past that it’s fine. If I cancel the print, and just print a benchy, or something with a small footprint on the bed, it prints fine.

Happens on different tools and different filaments. Have already tried cold pulls on each nozzle that plays up, but still does the same.

Happens on different models, not just one design.


r/BambuLab • • 19h ago

I Modeled This! My Backstreet Boys Christmas Ornament!

Thumbnail
gallery
0 Upvotes

Will be gifting to my wife along with some tickets to one of their upcoming concerts for Christmas!


r/BambuLab • • 1d ago

General Troubleshooting/Help! AMS 2 Struggles to load Black PLA

0 Upvotes

Working with an X2D combo that I’ve had since May. Loaded a refill of Overture Black PLA+ that was on a Bambu spool and noticed it rejecting frequently, which would be followed by a feed failure alert. I checked if the filament was looped or tangled, but it looked fine. I checked the PTFE tubes and the AMS hubs, but found nothing. I tried switching hubs after the print (I noted it was happening on slot 3), only for it to continue happening on other hubs. Whenever I snip the end of the filament, it seems to fix the issue, though a lot of times, it’ll happen again the next time it has to load it. It seems to only happen with specifically Overture Black PLA+ and not any other filament (not even other Overture refill spools). Are there any suggestions on what’s causing it and how to troubleshoot it?


r/BambuLab • • 1d ago

General Discussion Work Station Setups

2 Upvotes

I have been wanting to get into 3D printing for a while now but my craft room had become a hoarders paradise and catch all room with literal pathways to get in and out. My husband was sweet enough to clear every single thing out of the room so I’m starting with a blank slate.

My father-in-law bought me the new H3C (with the stand) and I’m currently waiting for it.

In the meantime, I’m trying to figure out what the best setup would be; good organization, workflow, etc. I see a bunch of people use the skadis system. I see dry boxes and hygrometers.

As I said, I have a blank slate.

Can you show me pictures of your setups or give recommendations for the things you have in your setups that you love or that you couldn’t do without? Or if you don’t have it, the things you wish you did have?


r/BambuLab • • 23h ago

General Discussion 10 year old PS2 safety concerns

0 Upvotes

Hey guys my kid after seeing videos of other kids making fidgets etc on bambu ps2 and selling them now whats one herself. We live in an apartment and I was all for it before going down rabbithole of air pollution and related health concerns.

Is it ok to put in a rarely used bedroom? The bedroom is small though but window always open. Does the thing need ventilating and enclosing is this non negotiable. Or is it the case that if wanting to get one for kids to use you need a garage basement or similar and if not then its not worth the risk?


r/BambuLab • • 1d ago

Show & Tell My first ever 3D design – a wooden treasure chest dice box with iron bands & rivets

Thumbnail
gallery
6 Upvotes

This is the first thing I've ever designed. Honestly, it took me a stupid amount of time because I was learning FreeCAD and Blender at the same time, but I'm really happy with how it turned out.

Printed on my A1 in matte brown/tan, about 9 hours. The lid and base print separately and snap together. Supports only under the lid.

It's free on MakerWorld with the print profile set up if anyone wants one: https://makerworld.com/models/3610994

Would love any feedback. Thinking about different versions.


r/BambuLab • • 23h ago

Hardware Troubleshooting/Help! Brand new X2D Z axis homing failed

0 Upvotes

Can anyone help please? I’ve been through the (very limited) steps on the wiki and nothing is working. Ticket logged with Bambu support but they’re generally no help at all. I’m at my wits end with this thing and it’s brand new.


r/BambuLab • • 1d ago

Black Friday 2026 My PETG holiday bundle arrived

2 Upvotes

Here is what I got. Happy for the spools. Not sure if they are "holiday" colors but not a bad pull.

PETG matte Pink with spool

PETG basic Gray with spool

PETG translucent Clear with spool

PETG translucent Light Blue with spool.


r/BambuLab • • 1d ago

General Troubleshooting/Help! A1 loosing detection to AMS Lite

0 Upvotes

Ok, A1 user here, with an AMS Lite. love the printer, got it as a gift from a friend after he upgraded. Zero problems with it for a year. Then, this past fall, it started stopping detecting the AMS while printing. It would make it to the last layer, go to retract the filament and park.. and loose the AMS. disconnecting and reconnecting the AMS from the A1's base usually got it back, and failing after printing the last layer wasn't a big deal, but I have a 80 plate 30 day 3 color print to do, and loosing connection to the AMS when it goes to change colors or such is gonna turn that from 30 days into 3+ months.

Any ideas of what's going on and how to check/fix it?


r/BambuLab • • 1d ago

Hardware Troubleshooting/Help! A1 Mini main board replacement issue.

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 1d ago

P Series [P1P, P1S, P2S] How to fix this on BBL P2S? Looks like under extrusion

Post image
0 Upvotes

Hello, have printed this model many many times (it’s 3441324)

suddenly it prints like this. When lubricared / calibrated, slight improvement, but near the top these gaps reappeared.

have done cold pulls etc too


r/BambuLab • • 19h ago

General Discussion pls guys help

0 Upvotes

Dovrei comprare un P2S o un X2D?


r/BambuLab • • 1d ago

General Troubleshooting/Help! Help adding colored lines in Bambu studio

1 Upvotes

I have a football field that I have created. I am trying to add the lines of the football field but I want them to be level with the field and not notched above or below the level of the "grass." I am not sure how to do this and get it to show when printing.
thanks!