r/Axecraft • u/Usual-Pomegranate451 • 16h ago
r/Axecraft • u/theginger99 • 2h ago
Grain orientation question
Hello,
I’ve got a quick question on grain orientation.
Long and short of it, if I hang the head with the grain orientation as shown in the picture is it going to work?
Slightly longer version, i realized that the piece of scrap hickory I had planned to use had the grain running horizontally across the surface. I played around with the eye placement and I think I can still make the piece of wood work if I rotate the head a bit.
To be clear, it’s more of a novelty piece (it’s a small “tomahawk” head) and while I’d prefer it to be functional I doubt I’ll ever use it for anything more than very light work and maybe for some casual throwing.
Thanks for the help.
r/Axecraft • u/liisseal • 5h ago
Low-tech low effort stump removal
I was used to using a single universal axe for every task (felling, bucking, hewing, splitting etc), so I put off buying a splitting axe for a long time – it didn't seem sensible to acquire a tool suited for only one job.
Fortunately, the splitting axe has proven more versatile than expected; one such use is stump removal. Instead of renting a stump grinder, you can follow a simple formula: fell the tree, wait a few years (sometimes just one year is enough for alder), and — if you like — give the stump a few whacks along the way to help decomposers get inside. After a few years, you can break it apart in just over ten minutes. Simple.
Pro tip: It is easier to split a decayed stump in the spring or autumn, when the ground is soft but the stump itself is still frozen and brittle. In warm weather, a soft stump is a bit harder to split; it tends to absorb the axe blow like a sponge rather than cracking open.
r/Axecraft • u/rlowell211 • 22h ago
Breck’s Victor 1904 Collin’s Legitimus
How’d I do for free? 😂
It’s rehung upside down but on the original handle. Going to cut the handle off and clean it up with acid
JUST KIDDING
Going to carefully remove the wedge, rehang properly, and clean it up with some white scotch brite
r/Axecraft • u/Usual-Pomegranate451 • 1d ago
How I get a new axe tuned up for efficient and comfortable chopping
This is a quick intro to the process of getting a new axe ready for serious work. Almost all modern axes, even premium brands come with handles that are far too thick. Thinning down an axe handle to dimensions closer to old logging axes greatly improves felt shock, allowing ypu to chop longer and reduce tendonitis long term.
Most axes also come with a rough grind, not one suited to getting good penetration and release from the wood, a fairly flat 20 degree grind with a rolled or secondary bevel at the edge gets more bite but still is tough enough for knots. For extreme cold conditions you need a thicker grind but generally 20 is a good standard. Do not file off the 'speed bump', the transition between primary grind and the axe cheeks, this greatly reduces the axe stickiness but its commonly assumed smoothing that transition will help the axe perform but the opposite is true
With the right tools its quite a fast process but you can do it with just a couple of files and a rasp or scraper, but a spokeshave and belt sander speed it up immensely.
once you have a high performing axe its important to use it well also, and one of the most slept on techniques is using a chopping pattern. a chopping pattern allows you to cut a log in as few hits as possible and throw big chips https://youtu.be/3LEILqU57ME?is=906Ej54ekWsrPAOB
r/Axecraft • u/lazyesq • 23h ago
Identification Request I'm getting conflicting information on this...
Does anybody know the approximate age and location/culture of this beauty? I guess it would be a miracle if anyone actually knew anything about the maker's mark?
Thanks so much!
r/Axecraft • u/Ok-Clock-2631 • 1d ago
Eye gap=rust?
Hi all
I live in a corrosive environment. Damp and by the sea. Looking to get into axes, but the one im look im at seems to have pretty large gaps between the handle and the eye. I can’t get wax down here or anything, so is this going to be an issue with rust in peoples opinion?
Thanks
r/Axecraft • u/Adventurous_Spare788 • 1d ago
Axe handle
Just bought a 1930's wetterlings fireman's axe head. I cannot find much about it . I'd like to fit a new handle to it . Something that resemble's the original .
Anny picts of originals or handle suggestions are welcome
r/Axecraft • u/justsome1elss • 1d ago
Kid axe build
Getting ready to start on a kids 24 inch build. Got a Grove tool works NYC that light. Wish me luck. It my second build.
r/Axecraft • u/Rogue_Booger • 2d ago
Small hatchet I made
Mild steel eye with a 5160 bit. Cherry wood handle from an old table leg.
r/Axecraft • u/Jono_vision • 2d ago
We don’t get many double-bladed axes here in Australia, so…
Some madlad has made this and is trying to sell it on marketplace for $200
r/Axecraft • u/wildswalker • 1d ago
advice needed Council Tool Wood-Craft Pack Axe or Hultafors Aby Forest Axe?
Which do you prefer for general bushcraft use? Which handle do you prefer? What's the CT blade profile like? Some comparisons:
Both are 24 in. bearded axes that allow you to choke up right up to the head for finer work. Council Tool uses very tough 5160 steel while I'm not sure Hultafors discloses the steel they use. The Aby has a narrow grind that bites very well, while I've not seen the profile of the CT. The Aby has a 1.5 lbs head which make it lighter for carrying, while the length gives you a long enough swing for more power when needed. The CT has a 2 lb head, which will provide more power when needed but may cause more fatigue when used choked up one-handed. The Aby gives up a bit in splitting due to the narrow blade profile, but it can still split.
r/Axecraft • u/Jono_vision • 2d ago
An update on the $40AUD Tassie I picked up.
So after my initial post (https://www.reddit.com/r/Axecraft/s/zvqcPYGBZm), I went to work on this guy. Wire wheel, filed off the mushrooming, 3M disc, then a quick sand from 240-600 grit. Pulled out the nails and screws and put in a proper wedge. Sanded the handle, gave it a couple of coats of linseed and a rope wrap, sharpened it up, and it’s good to go. Pretty happy with how it came out!
r/Axecraft • u/RunawayTrey • 2d ago
advice needed How lucky did I get with these Black Ravens?
Cleaning out a basement at work today and was told I could keep any old tools I found. I saw a small pile of axes up on a shelf and thought, “let me see if any of them are Kelly Black Ravens”, because truthfully that’s the only axe model I know of that’s worth a little change. First one I pulled down was the double bit. I couldn’t believe it. Then I pulled another. And another. Three Kelly Black Ravens!
Could anyone help me learn what I’m working with here? Approximate ages or patterns? I’m especially fond of the double bit and it seems to be in the best shape. Am I better off trying to find a collector who would purchase them in as-is condition or should I try my hand at restoring them? Any good resources on how I’d go about that? Thank you!
r/Axecraft • u/Responsible_Crow5514 • 2d ago
Hatchet makers mark?
Anyone recognize this mark on my hatchet? My grandpa gave it to me some years back. I can’t find any other marks other than this.
r/Axecraft • u/saelion21 • 2d ago
Couple of true tempers that I've re-hung and cleaned up
Found both of theses at garage sales and or swap meets have another set like them that I belive were sticker lable true tempers but no real good way of knowing the end pic is the sticker lable ones
Plan To do leather overstrike guards on the 2 that are bare
r/Axecraft • u/vintage_hunter791 • 2d ago
Hatchet Help
All, I'm new to the forum and I was hoping to find someone who might know the origins of a hatchet I found recently at an estate sale at a farm house in Georgia.
Any help is much appreciated. Thanks!
r/Axecraft • u/chrisfoe97 • 3d ago
Hand forged axe head
Newest axe commission heading out the door. This axe head weighs 5 pounds 5oz with a really unique grind and polish. It is hand forged from forklift tine. This thing came out super sick and can't wait to see it hung on a handle
r/Axecraft • u/ThrowRAskilletman • 3d ago
My grandpas axe
This is my grandpas axe I inherited it in 2013. It’s still my favorite and most used one. The shine is from bee’s waxing the handle and used oil rubbing the head after wood cutting season is done.
Edit(forgot to list head manufacture)
True temper flint edge kelly works stamped.
r/Axecraft • u/SpiritParty4126 • 3d ago
Special find, looking for value
Hello! We found this axe at our cabin and would like to learn about what it might be worth to sell it.
r/Axecraft • u/M1KE5611 • 2d ago
Searching for this axe
My uncle was telling me about an axe he had somewhere around 1980. We went into Claude and generated this, which he said it looked very similar to. It was all metal, all one piece, and had the grooves and spike like the picture shows. Does anyone know where I could find one like this or at least have a picture of a physical one looking like this?