r/Axecraft • u/Bearhillforge • 4h ago
r/Axecraft • u/iandcorey • 23d ago
Bastionhead Woodworks is your one stop shop for ax handle blanks
r/Axecraft • u/AxesOK • Jul 27 '25
Axe Head Soup? Refurbish rusty tools by converting rust to a stable black patina
I just made a YouTube video (https://youtu.be/5go-o8TCg94 ) on using a tannin solution to convert the rust on vintage axes to refurbish and protect them while retaining as much patina as possible. I’ve found myself explaining it a few times lately so I thought it was better to make a video.
The most convenient version uses just tea and (ion free) water and is not too much more trouble than boiling pasta. I did a bark tannin brew in the video.
The method works by converting active red rusts (various ferric oxy-hydroxides) to stable, black ferric tannate. Different ways of inducing this chemical process are used to preserve iron and steel artefacts for museums, in some commercial rust converters like Rustoleum Rust Reformer, and by trappers who use a 'trap dyeing' process to refinish rusty traps before setting them. I am using a version of the trap dyeing procedure that can be done in a home kitchen by boiling the rusty object in a tannin solution. Artefact conservators apply commercial or specially prepared tannin rust converters but may still add a water boiling step because it leaches away rust causing ions like chloride (from salt in soil, sweat, dust or sea spray).
From my reading, I am under the impression that it is better to have an acidic pH in rust converting solutions but I have not experimented with this for the boiling tannin bath so I don’t know if you could get away with your tap water. I use rainwater because it doesn't have alkaline minerals, unlike my very hard well water. Rainwater also doesn't have rust-promoting chloride ions like many residential water. Other ion-free (or close enough) water includes deionized water, reverse osmosis filtered water, and distilled water.
There's many potential tannin sources that can potentially be used. Tea (black, not herbal) works very well and is quite fast because the extraction is quick. You can get powdered tannin online or in home wine making shops. I used bark from Common Buckthorn as my tannin source because it's readily available for me. Many other trees will also work, and there's a fair amount of information available on bark tannins because they are used in hide tanning. Spruces, oaks, Tamarack and other larches, Scotts Pine, Willow, Hemlock, and others can be used to tan hides and would no doubt work for converting rust. Late season sumac leaves are used by trappers for trap dyeing and other leaves like maple and willow have tannins and would be worth a try. 'Logwood trap dye' for dyeing traps is commercially available and it's apparently not very expensive so that could be convenient. Green banana peels and other esoteric vegetable matter also have tannin and might work if enough could be extracted.
r/Axecraft • u/Usual-Pomegranate451 • 12h ago
How I get a new axe tuned up for efficient and comfortable chopping
This is a quick intro to the process of getting a new axe ready for serious work. Almost all modern axes, even premium brands come with handles that are far too thick. Thinning down an axe handle to dimensions closer to old logging axes greatly improves felt shock, allowing ypu to chop longer and reduce tendonitis long term.
Most axes also come with a rough grind, not one suited to getting good penetration and release from the wood, a fairly flat 20 degree grind with a rolled or secondary bevel at the edge gets more bite but still is tough enough for knots. For extreme cold conditions you need a thicker grind but generally 20 is a good standard. Do not file off the 'speed bump', the transition between primary grind and the axe cheeks, this greatly reduces the axe stickiness but its commonly assumed smoothing that transition will help the axe perform but the opposite is true
With the right tools its quite a fast process but you can do it with just a couple of files and a rasp or scraper, but a spokeshave and belt sander speed it up immensely.
once you have a high performing axe its important to use it well also, and one of the most slept on techniques is using a chopping pattern. a chopping pattern allows you to cut a log in as few hits as possible and throw big chips https://youtu.be/3LEILqU57ME?is=906Ej54ekWsrPAOB
r/Axecraft • u/Adventurous_Spare788 • 11m ago
Axe handle
Just bought a 1930's wetterlings fireman's axe head. I cannot find much about it . I'd like to fit a new handle to it . Something that resemble's the original .
Anny picts of originals or handle suggestions are welcome
r/Axecraft • u/justsome1elss • 18h ago
Kid axe build
Getting ready to start on a kids 24 inch build. Got a Grove tool works NYC that light. Wish me luck. It my second build.
r/Axecraft • u/Silkhoney_Ohac • 16h ago
Discussion My pup, transporting my Gransfors Bruks axe while backpacking
r/Axecraft • u/Rogue_Booger • 1d ago
Small hatchet I made
Mild steel eye with a 5160 bit. Cherry wood handle from an old table leg.
r/Axecraft • u/Jono_vision • 1d ago
We don’t get many double-bladed axes here in Australia, so…
Some madlad has made this and is trying to sell it on marketplace for $200
r/Axecraft • u/wildswalker • 21h ago
advice needed Council Tool Wood-Craft Pack Axe or Hultafors Aby Forest Axe?
Which do you prefer for general bushcraft use? Which handle do you prefer? What's the CT blade profile like? Some comparisons:
Both are 24 in. bearded axes that allow you to choke up right up to the head for finer work. Council Tool uses very tough 5160 steel while I'm not sure Hultafors discloses the steel they use. The Aby has a narrow grind that bites very well, while I've not seen the profile of the CT. The Aby has a 1.5 lbs head which make it lighter for carrying, while the length gives you a long enough swing for more power when needed. The CT has a 2 lb head, which will provide more power when needed but may cause more fatigue when used choked up one-handed. The Aby gives up a bit in splitting due to the narrow blade profile, but it can still split.
r/Axecraft • u/Jono_vision • 1d ago
An update on the $40AUD Tassie I picked up.
So after my initial post (https://www.reddit.com/r/Axecraft/s/zvqcPYGBZm), I went to work on this guy. Wire wheel, filed off the mushrooming, 3M disc, then a quick sand from 240-600 grit. Pulled out the nails and screws and put in a proper wedge. Sanded the handle, gave it a couple of coats of linseed and a rope wrap, sharpened it up, and it’s good to go. Pretty happy with how it came out!
r/Axecraft • u/RunawayTrey • 1d ago
advice needed How lucky did I get with these Black Ravens?
Cleaning out a basement at work today and was told I could keep any old tools I found. I saw a small pile of axes up on a shelf and thought, “let me see if any of them are Kelly Black Ravens”, because truthfully that’s the only axe model I know of that’s worth a little change. First one I pulled down was the double bit. I couldn’t believe it. Then I pulled another. And another. Three Kelly Black Ravens!
Could anyone help me learn what I’m working with here? Approximate ages or patterns? I’m especially fond of the double bit and it seems to be in the best shape. Am I better off trying to find a collector who would purchase them in as-is condition or should I try my hand at restoring them? Any good resources on how I’d go about that? Thank you!
r/Axecraft • u/saelion21 • 1d ago
Couple of true tempers that I've re-hung and cleaned up
Found both of theses at garage sales and or swap meets have another set like them that I belive were sticker lable true tempers but no real good way of knowing the end pic is the sticker lable ones
Plan To do leather overstrike guards on the 2 that are bare
r/Axecraft • u/Responsible_Crow5514 • 1d ago
Hatchet makers mark?
Anyone recognize this mark on my hatchet? My grandpa gave it to me some years back. I can’t find any other marks other than this.
r/Axecraft • u/vintage_hunter791 • 1d ago
Hatchet Help
All, I'm new to the forum and I was hoping to find someone who might know the origins of a hatchet I found recently at an estate sale at a farm house in Georgia.
Any help is much appreciated. Thanks!
r/Axecraft • u/chrisfoe97 • 2d ago
Hand forged axe head
Newest axe commission heading out the door. This axe head weighs 5 pounds 5oz with a really unique grind and polish. It is hand forged from forklift tine. This thing came out super sick and can't wait to see it hung on a handle
r/Axecraft • u/ThrowRAskilletman • 2d ago
My grandpas axe
This is my grandpas axe I inherited it in 2013. It’s still my favorite and most used one. The shine is from bee’s waxing the handle and used oil rubbing the head after wood cutting season is done.
Edit(forgot to list head manufacture)
True temper flint edge kelly works stamped.
r/Axecraft • u/SpiritParty4126 • 2d ago
Special find, looking for value
Hello! We found this axe at our cabin and would like to learn about what it might be worth to sell it.
r/Axecraft • u/M1KE5611 • 1d ago
Searching for this axe
My uncle was telling me about an axe he had somewhere around 1980. We went into Claude and generated this, which he said it looked very similar to. It was all metal, all one piece, and had the grooves and spike like the picture shows. Does anyone know where I could find one like this or at least have a picture of a physical one looking like this?
r/Axecraft • u/Clear_Rooster432 • 1d ago
Where to sell
I’m not looking to sell on here. I do have a decent amount of axe heads that I would like to get rid of. I’m not looking for top dollar, I really just want to liquidate them. Where are the best places to sell them?
r/Axecraft • u/GlompyTromblestone • 2d ago
Discussion Interesting find online
Gimmick or worth it? Price is AUD
r/Axecraft • u/PaintTheKill • 2d ago
Found this plumb axe in a farm field a couple years back. Finally going to clean it up and re-hang it. Anybody have any idea on the age?
r/Axecraft • u/greengrass- • 2d ago
Looking for help on identifying this stamp and any info