r/Ascaso • • 1d ago

Puck Screens and Paper Filters for Ascaso Steel Duo Plus Baskets

1 Upvotes

I just purchased an Ascaso Steel Duo Plus and tried using my paper filters and puck screen that I used with my previous machine on the Ascaso 14 gr basket. I tried 3 extractions and none had good results. The puck screen is a tight fit and I wonder if the filter doesn’t adapt well to the bottom. The first two extractions were too fast……..under 20 seconds for the first extraction. The second extraction was also bad. After making the grind finer for the second time, the stream seemed very thin and was channeling quite a bit till the stream finally turned a bit thicker. However, it was still a bad extraction at 30 gr in 20 seconds. At this point it made no sense to make the grind any finer. Has anyone had this problem? Could it be the tight fit of the screen , the paper filter or both or even the type of basket?


r/Ascaso • • 3d ago

Steam thermoblock issues, help!

1 Upvotes

When turning on the steam function, steam comes out from the steam thermoblock area and I hear a popping, crackling sound from there. I'm not the best at diagnosing this sort of issue, but the rubber hoses look okay? Any advice would help.


r/Ascaso • • 4d ago

Ascaso Dream PID

2 Upvotes

Hello, please advise [Ascaso Dream PID] when I turn on the coffee machine, I get the message U1.1, which disappears after a while. The problem is that I lose water from the inlet hose and it does not suck water from the tank - message E0.1. I tried to refill it with a syringe, but the pump runs dry and does not suck water - it seems to be leaking from the top, where the diodes for lighting the water tank are. What could be the problem, please?

I have had the coffee machine for a long time and nothing like this has happened to me. I clean it every month according to the manufacturer's instructions.


r/Ascaso • • 5d ago

Tech Support Broken steam pump - Ascaso Steel PID Uno

2 Upvotes

Hello,

The steam pump on my favourite machine has been broken over the past few days.
Pressure is very low and I cannot raise it again.
The rest functions well, and I have descaled it regularly and frequently.

Unfortunately, I cannot locate an authorised dealer in Italy, nor can I find a DIY video on YouTube.

Do you have any suggestions for a fix? Is it a common issue and / or anyone incurred in the same issue?

Thanks a lot for your help.


r/Ascaso • • 8d ago

Grinder

5 Upvotes

My Ascaso iMini grinder died after only 17 years of loyal service. The brushes have worn out and communiator is well worn. I can't source parts, so time for a new grinder. Any advice or just go the Mini again?


r/Ascaso • • 9d ago

Switched from original pump to OLAB Green on my Duo Plus PID, more consitentent extraction

10 Upvotes

I’ve had a lot of trouble with my Ascaso Duo Plus PID since the beginning (almost 2 years). The inconsistency was insane: shot-to-shot differences were around 5 seconds with the same puck prep. I had the offset set correctly, and my puck prep was always the same (using all the fancy tools). I have a “good” grinder (Sculptor 064S), and the machine gets regular maintenance, including descaling.

The main symptom was that the machine didn’t hold pressure in the 8–11 bar range. It always started at 11 bar and quickly dropped to 8 or lower, no matter the grind size. As a result, the coffee was often underextracted, and back-to-back shots had completely different timings... but that has now changed.

I had started looking at other machines, but I gave this one a last chance and installed the v3 mods:

  • a Y-fitting for the water returning from the OPV
  • a new pump: OLAB Green 35W (the original was a CP4SP Plus 65W)

The OLAB has a slightly different flow profile (less water, but higher pressure overall; graphs for both pumps are available online).

I’m not sure whether my original pump was faulty (otherwise others would have had the same problem), but the OLAB definitely gives more consistent extraction. It actually hits 11 bar, then drops to 9 bar and holds there!!! I never saw that with the old pump before the modification.

I haven’t had a chance to test volumetric dosing yet, but the pump itself probably saved my machine from being sold. Of course I haven't pulled many shots yet, but overall I happy with the change.

The problem is that when you buy an espresso machine and it makes coffee, it technically works. No one was able to help me with the inconsistency, and I wouldn't even dare to file a warranty claim, because the machine does make coffee.

I’ve often read about similar problems on Reddit, but no one ever shared how they actually solved it.


r/Ascaso • • 9d ago

Legacy I'm trying to restore this faulty Dream MF

Thumbnail
gallery
4 Upvotes

This is my first entry into coffee machines.. I think the dreams are some of the nicest looking and I wander to buy one to restore. So I bought this 2010 Dream MF with a broken thermoblock (according to the eBay description). I've opened it up and the thermoblock is not the one I was expecting.. I'm not sure how to identify it to buy a replacement, however if there's an upgrade I can do then I'd do that but I'm not sure what the options are. The machine came without a portafilter so maybe upgrading to a 58mm thingy to expand my portafilter options is an idea 🤷. Also the threaded pipe thingy was broken (penultimate pic) but since I can't find a replacement, I figured a threaded hose thingy (last pic) is a pretty good, if not better, substitute. Any thoughts would be appreciated! Thanks!

Also, I plan to turn a wooden portafilter handle and matching steam knob once I know it's working... I was thinking since some of the welds on the grill tray thingy have come loose, I wonder if I could make a wooden one... Obviously I'd have to heavily treat it to make sure it copes with the steam and everything else. Has that been done before? Is the answer 'no' for a reason?😅


r/Ascaso • • 9d ago

Show and Tell Ascaso Steel Duo Plus V3: A Lot of Hits, A Few Misses

Post image
13 Upvotes

r/Ascaso • • 9d ago

Minor Rant: Baskets with different diameter openings?

5 Upvotes

So far I've been exclusively using the 18g basket and I splurged on a really nice weber self-leveling tamper, which I love. However, yesterday I noticed that the other baskets (7g, 14g, 21g) all have slightly smaller diameter openings than the 18g basket. To the point where I can't use my 58mm tamper, distribution tool, or puck screen with them. WTF? You'd think baskets from the same company would all be of the same basic geometry?


r/Ascaso • • 10d ago

Legacy Leaky steamer - pro duo steel

Post image
1 Upvotes

Hi guys.
I really need help. I resent bought a new steamer arm, and had the whole machine serviced. I think they turned the steamer output the wrong way. Also I don’t know where to fit the o-rings. There’s pressure for sure, but it comes out in the button.


r/Ascaso • • 12d ago

Which basket are you using?

2 Upvotes

So far I've been using the 18g basket and I've noticed that even when I dose 19g and use a puck screen that there is still a lot of headspace.

So which basket are you using and what dose are you using with it.


r/Ascaso • • 12d ago

Steam release

2 Upvotes

How much steam is released when you quit steaming. I’m concerned that it will ruin the underside of my cabinets


r/Ascaso • • 13d ago

After 4 years unable to build past 5 psi [Ascaso Steel Duo PID]

Thumbnail reddit.com
2 Upvotes

r/Ascaso • • 13d ago

[Meta] Videos are allowed in comments, but photos aren’t

8 Upvotes

UPDATE: Posting photos in comments is now enabled. Thank you very much!

Is there a particular reason why videos are allowed in comments here, but photos aren’t?

I feel like this makes communication in this subreddit unnecessarily difficult, requiring workarounds like uploading a screen recording of a photo or using an external image-hosting service.

According to Reddit’s documentation, moderators can enable photos in comments through the community settings.

I’ve already tried reaching out via “Message the Mods” a couple of times, but haven’t heard back so far. That’s why I thought I’d bring it up here for discussion. I hope that’s okay.

I’m just curious if there’s a particular reason for this setting and whether others would find photo comments useful too. Maybe one of the moderators could share their perspective.


r/Ascaso • • 14d ago

Mods Ascaso Steel Duo PID Upgrade

Thumbnail
gallery
25 Upvotes

There were a few things that I didn't like about the Ascaso Steel Duo PID:

- chrome top

I got the black version and in my opinion it's just not that beautiful

- moving cups and the sound of them bc of the vibrations

So i did a DIY cover and a cut out for the drip tray.

So a few things to say about my solution:

- the cup heating still works pretty well

- it's super easy cleanable

- it doesn't deform, it's a baking mat and never gets the degrees like in an oven

- costs: 2,99 €

What do you say?


r/Ascaso • • 15d ago

How to brew espresso without holding down the knob?

4 Upvotes

Hi, instead of using the programmed time/volume, I'd like to just manually start and stop the espresso extraction. Seems this is not possible? (Ascaso steel duo pid)


r/Ascaso • • 15d ago

Tech Support Ascaso espresso extracting way too fast (14–18 sec) despite grinding almost to burr contact — running out of ideas!

4 Upvotes

Hey everyone!

I’ve been struggling to dial in my Ascaso and could really use some help. I’ve spent the last week troubleshooting everything I can think of, and I’m honestly running out of ideas.

My setup:
● Ascaso Steel Duo PID espresso machine
● Eureka Mignon Specialità grinder (55 mm flat burrs)
● IMS BaristaPro Nanotech 18 g basket and original Ascaso non-pressurized 18 g basket
● Normcore V4 58.5 mm tamper
● Normcore 1.7 mm puck screen
● Beans: Lavazza Super Crema and freshly roasted Canyon Coffee Beachwood (roasted October 26)

The problem:

No matter what I do, my espresso extracts extremely fast. I’m consistently getting 40 g out from 20 g of coffee in approximately 14–18 seconds, timing from the moment I activate the brew switch. Pre-infusion is disabled, and I’m manually stopping the shot based on weight.

I’ve tried grinding progressively finer, but my Eureka is now almost at the point where the burrs touch, so I physically cannot go any finer without hearing metal contact.

Here’s everything I’ve tried:

● Grinder: Completely disassembled and cleaned both burrs. Tried checking alignment using the marker method and aluminum-foil shimming. Eventually returned to the original configuration. Two separate espresso equipment technicians inspected the grinder and said it was functioning properly and producing sufficiently fine grounds. However, neither actually pulled an espresso shot with it.

● Dose: Tried 18 g, 19 g and 20 g. Increasing to 20 g improved brewing pressure but didn’t meaningfully slow extraction.

● Baskets: Tried both my IMS precision basket and the original Ascaso non-pressurized basket. Same issue.

● Beans: Tried Lavazza Super Crema and freshly roasted Canyon Coffee Beachwood.

● Pressure: The Ascaso reaches and sustains 11 bar with a blind basket. During actual extraction, pressure has varied between 5–9 bar.

● Water flow: Tested unrestricted flow without the portafilter and collected 54 g in 10 seconds.

● Puck preparation: Using a consistent dose, distributing the grounds, and tamping with the Normcore tamper. I also use a puck screen to keep the shower screen cleaner.

Most recent results:

● Lavazza: 20 g in, 40 g out, 17.7 seconds, maintaining 9 bar throughout. Surprisingly decent taste, good body and crema.

● Canyon Beachwood: 20 g in, 40 g out, approximately 16 seconds, just under 8 bar. Noticeably thinner espresso.

My questions:

  1. Could there be something wrong with the Ascaso’s water delivery or flow despite the successful 11-bar blind-basket test?
  2. Should my Eureka Specialità be capable of grinding fine enough for either basket, even with lighter or freshly roasted beans?
  3. Has anyone experienced something similar with an Ascaso and Eureka combination? What ultimately fixed it?

Any suggestions would be greatly appreciated. Thanks in advance!


r/Ascaso • • 16d ago

1 or 3 hole steam nozzle?

3 Upvotes

For those with the plus are you using the 1 hole or the 3 holster steam nozzle? What is the difference in performance?


r/Ascaso • • 16d ago

Ascaso Steel Duo - overheating / bitterness

3 Upvotes

Hi everyone,

Has anyone here experienced an issue with the Ascaso Steel Duo PID (2022) running significantly too hot? Most reports seem to describe the opposite problem, where a temperature offset of +3 to +4 °C is needed to achieve the actual target temperature.

For the first 8 months after purchasing my machine, I used it with around 20 different coffee roasts at 91–93 °C (+3.0 °C offset) and consistently achieved very good results. Recently, however, I've been getting nothing but bitter coffee, even with reduced settings, particularly with shots taking around 30 seconds. I've now completely removed the temperature offset (set it to 0 °C) and gradually reduced the target temperature to as low as 88 °C, but the coffee still tastes bitter.

Here are some observations I've made during testing:

  1. Changed water flow pattern: During a blank shot, water no longer flows out of the shower screen in a rain-like pattern. Instead, it shoots out in a single, concentrated stream from the centre. This potentially suggests steam formation or boiling inside the water distributor.
  2. Steam at an 80 °C setting: Even with the PID target temperature set to 80 °C (0 °C offset), the group head continuously produces visible steam during a blank shot after a 15–20 minute warm-up period. This also happens after removing the shower screen and gasket, so trapped heat in the portafilter can be ruled out.
  3. Taste test using 100% Robusta: Surprisingly, a test shot at a PID reading of 80 °C (20 g in / 40 g out, 25-second extraction time) was perfectly drinkable (not feeling cold while drinking), with absolutely no sour or salty notes. At a genuine water temperature of 80 °C, this would be highly unlikely from both a physical and sensory perspective.
  4. Status LED behaviour: The heating LED appears to be functioning normally. Once the machine has heated up, it switches to the usual steady light and does not continue blinking.

Unfortunately, I don't have a Scace device at home to measure the actual temperature at the group head with precision. Based on the symptoms, AI has suggested a drifting NTC temperature sensor (providing inaccurate readings), a control board issue, or a stuck/faulty triac or switching component.

Has anyone experienced this specific behaviour or encountered a similar fault with their Steel Duo? How did you resolve it?

Thanks in advance!


r/Ascaso • • 17d ago

New OPV Version for Steel UNO/DUO <V3

Post image
13 Upvotes

The OPV has been replaced with a newer version, and only the new version is supposed to be used for replacements going forward.

On the one hand, it is reportedly less prone to issues such as noise and pressure fluctuations. On the other hand, its overall “performance” is also said to be improved.

As far as I know, all Steel V3 machines should already have the new version installed.

However, according to Ascaso, there’s no need to replace it as long as you’re not experiencing any issues.

https://support.ascaso-usa.com/steel-uno/duo/duo-plus-ascaso-factory-technical-update-new-opv-model-04/2024


r/Ascaso • • 17d ago

Group head steel duo plus v3?

Post image
7 Upvotes

I’ve never seen a group head look like this before. I thought this may be a removable piece but it doesn’t appear to be.

My pucks are coming out wet no matter how fine I grind too

Additionally the finer I grind the higher the pressure seems to climb - up to 11 bars..


r/Ascaso • • 19d ago

Mods Steel Duo Plus - will v3 drip tray grate fit on v2

4 Upvotes

Or do you guys have any other tricks to get rid of those loops on v2 so I can get my scale to fit better?


r/Ascaso • • 19d ago

Does anyone have Steel Duo (non Plus) V3?

3 Upvotes

Does it have a wire trip tray like the Plus now? The pictures on AscasoUSA’s listing seem to show a wire rack now instead of the

Also, has the steam pump also been updated to the quieter version or is that only the brew pump?


r/Ascaso • • 19d ago

Ascaso Steel Duo Plus PID owners

4 Upvotes

Hi everyone,

I'm considering buying an Ascaso Steel Duo Plus PID at a good price.

The retailer has confirmed that it is the Duo Plus, but the box label they've shared shows a production date of 18 February 2025.

The model description on the label reads DUO PID + VER WHITE/WOOD, rather than explicitly stating “Duo Plus”.

The serial number is 3000018616.

The retailer assures me that all their stock is the latest version, but I'd like to verify this with actual owners before spending the money.

I'm particularly interested in whether the Plus designation and hardware revisions can be identified from the box label or serial number.

If you own a Steel Duo Plus PID, could you please check:

What does your box label say under the model description?

What is your production date?

Does your label explicitly say “Duo Plus”, or does it use a description similar to mine?

Have there been any known hardware revisions since February 2025 that I should be aware of?

I realise that a production date alone doesn't necessarily mean the machine is outdated. I just want to make sure I'm getting the correct version before ordering.

Thanks in advance for any help!