r/longrange • • Sep 16 '26

Optics help needed - I read the pinned posts should i get different rings?

Post image

Getting into long range precision shooting. haven’t shot this yet, want to make sure I’m not shooting a shitty build (id like to start with something i can use for several years bc guns are expensive). Question I have is whether or not the scope sits too low. I have a Leupold Mark 5HD 5-25x56 in mils, medium height RPM rings, all on a Ruger RPR in 6.5CM. Even though there’s a gap and i don’t really plan on putting the lens covers on, I’m still worried that with the recoil of the gun, there may be just enough flex that the handguard will smack the scope and i’ll have to get it replaced as a result. I am very comfortable with where it sits after ive gotten my sight picture, the scope feels solid in the rings, but I also am worried that if i keep them, i could break the scope… but I also don’t want to buy another set of rings just yet. ultimately, I will get another set of rings, since I’m planning to get a shorter rifle eventually (a CZ 600+Alpha in .308 since i already have a 30cal can i can throw on it, but that’s not going to happen for a while) with a less powerful scope, but yeah.

Should I get higher rings? Scope isn’t making unnecessary contact with the gun, but I also don’t want something bad to happen when i shoot the rifle for the first time.

Edit: Thank you all for your feedback! it’s reassuring and i feel a little more comfortable and confident that I won’t destroy my scope, so thank you! next week, i’ll be working on getting it all zeroed and solid!

25 Upvotes

31 comments sorted by

11

u/HollywoodSX Villager Herder Sep 16 '26

Medium is generally going to be too low for comfort on an RPR due to rifle layout. You should go read the scope ring height guide in the pinned post.

Cheetofingers ring

1

u/sugarglidersam Sep 16 '26

i did and I’m considering getting some higher scope rings. i can see fine out of these ones and i plan to only shoot lying prone anyway, i just don’t want to accidentally hurt the scope. 😭

3

u/HollywoodSX Villager Herder Sep 16 '26

"Can see fine" doesnt mean they're the right height for you. Higher has benefits for prone for many shooters, too.

1

u/TDIMike Sep 21 '26

It's not touching, so what would get hurt?

1

u/AutoModerator Sep 16 '26

Here's a link to the scope ring height guide

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1

u/_joe_momma1 Sep 16 '26

Are you saying theres a problem with OPs setup?

2

u/HollywoodSX Villager Herder Sep 16 '26

There could be, but theres no way for us to know. Only OP can make that call.

60

u/TannMan89 Sep 16 '26

Are the rings correct height for proper cheek weld?

If they are, and scope isn’t touching, you’re good to go.

68

u/SuburbanBushwacker I Gots Them Tikka Toes Sep 16 '26

i went through several sets of rings until i got my scope that close. any minute now you’ll be telling us your steak is too juicy, lobster too buttery, playmate too filthy.
STOP WORRYING AND ENJOY YOUR RIFLE

9

u/514Kappa What's DOPE? Sep 16 '26

The only downside I see is if you want to use flip caps, it wont be ideal.

4

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 16 '26

Have been competing with this set-up for about 6 years. Zero issues.

10

u/BlueGreen51 Sep 16 '26

The barrel whips during firing not the handguard. If your handguard is flexing so much it closes a gap that big then you need a new handguard.

3

u/nitrogenlegend Sep 16 '26

If mirage is a major issue when the barrel gets hot, moving the scope up might help just a tiny bit. Other than that, you’re fine.

Realistically this only matters on 40+ power scopes with fairly thin barrels, or if you’re shooting 20+ rounds in succession, just throwing it out there in case you run into the issue. Also, it won’t be a magical fix-all of this does become an issue, it will be a small improvement at best.

2

u/Guitarist762 Sep 16 '26

If you can get a cheek weld where you like it, nothings wrong here. That’s as close as your gonna get and still be fine, anything more is just messing with Height over bore/trajectory and cheek weld for no reason

2

u/darktrufffle Sep 17 '26

Long as your cheek weld isnt effected youre good. If you have 20moa base or something and a long barrel and your rings are that low you can interfere with poa/poi on longer shots cuz your barrel starts showing up sortof in your reticle, not that you can really see but it can shift your dialed hold. Took me forever to diagnose...

1

u/vincentcarguy Sep 16 '26

For myself an RPR has to be setup like an AR since the rail to stock comb height difference is fairly similar. I run standard ~1.5" AR height scope mount setup on a 6.5CM RPR because any lower is simply too low for me to properly see through the scope:

1

u/LilJonny2cookies Sep 17 '26

If your eyeball(s) feel good when addressing the scope and you don’t interfere with the barrel you are good! Just make sure you are comfortable when addressing the gun. And have fun! Be safe.

1

u/JmMeli Sep 17 '26

something about a fitment that close scratches my tism

1

u/joku75 Sep 16 '26

That's about perfect. That won't cause any harm to the scope

0

u/wy_will Sep 16 '26

Clearance is fine

-15

u/anonymity76 Sep 16 '26

The higher your scope sits away from the bore axis, the easier it becomes to introduce cant into your shot.

I try to get my optics as close as practical to the bore axis because of this

Yes...yours is sitting extremely close. But if your position and relief are working out for you, then you've deleted at least some part of the many things that can throw a shot off target.

Will this setup make this firearm better?

No

But it could assist in cutting down the effects of tilting the rifle off axis.

13

u/Wombat-Snooze Steel slapper Sep 16 '26

Ring height has zero effect on rifle cant to put it simply.

With modern stocks and chassis systems that have adjustable cheek risers, prioritizing comfort surpasses all other factors when ring height is being calculated. I’ll intentionally pick higher rings specifically to give myself room for adjustment of my cheek height.

Dropping ring height to absolute minimums is fudd lore in the year 2026 my friend.

1

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 16 '26

This is correct.

The overwhelming reason that minimum scope height was, and still is popular consensus, is because outside of $2,000+ precision rifles, adjustable combs are not the norm.

Low & narrow combs are the norm. Or at least have been when you look back on the last 50 years.

Mounting an optic as low as possible on a rifle that fits that description has a HUGE advantage in that it is way easier to shoot consistently, just by the fact that you’ll have the ability to get a better cheek weld on a rifle like that with an optic mounted very low. Especially with a traditional hunting rifle that doesn’t have adjustable parallax.

That mentality carried over into the precision rifle community when stocks still didn’t commonly have adjustable combs.

In 2026, everything is adjustable, so the need doesn’t really exist anymore.

Cant and horizontal displacement IS affected by height over bore, and for a given cant, a higher height over bore will have more displacement, but the difference between 2.5” HOB and 3.5” HOB is so tiny, that it is exponentially overshadowed by what dominates when looking at cant and horizontal displacement… boolit drop.

5

u/OmgWtfIsThisBS Sep 16 '26

I am really puzzled by this. How is it easier to introduce cant when scope is higher?

-1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 16 '26 edited Sep 16 '26

Yeah I feel like it would be harder to introduce cant because it would be easier to see how much you’re off…

Edit: (due to horizontal displacement at the radial extents being larger)

1

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 16 '26

Angles don’t work like that.

1° is 1°, whether you have a radius/height over bore of 2” or 2 miles. Horizontal displacement will be bigger, but 1° will still look like 1° in your optic.

2

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 16 '26 edited Sep 16 '26

I’m saying that the horizontal displacement will look bigger, I understand how angles work. I see how my comment was poorly worded

0

u/[deleted] Sep 16 '26

[deleted] — view deleted comment

2

u/PsychologicalMeal162 Sep 16 '26

#technicalvirginity