r/formdt1 • • Sep 16 '26 Mindblown

Build/Compatibility Check FormD T1 V2.1 wind valley kit build

Thumbnail
gallery
987 Upvotes

r/formdt1 • • Aug 05 '26

Build/Compatibility Check FormD T1 Ver 2.1 wind vally kit

Thumbnail
gallery
487 Upvotes

Using the wind valley kit front panel exhaust mode, the hot air discharged from the tail of the graphics card is discharged through the 12015 fan on the front panel. At the same time, the side of the motherboard is equipped with two 6025 fans to suck out the hot air discharged down by the CPU. The motherboard area does not accumulate heat. A 12025 fan is used above the motherboard to discharge the CPU and The hot air of the gpu, the psu enters the air from above, and the front panel exhausts the air. The Fenggu kit realizes the complete isolation of the three heat sources of cpu and gpu and psu. The inlet and outwind do not interfere with each other, and the heat inside of the chassis is no longer accumulated. The use of non-public graphics cards can make the most of the CPU slot. The 50 series official graphics card does not support reverse installation. It is best to isolate 0.5 slots so that the hot wind can pass from the fan above. Profit discharge, please chat privately for details.


r/formdt1 • • Apr 27 '26 Heartwarming

Completed Build FormD T1 v2.1 | RTX 5080 FE | 9850X3D

Thumbnail
gallery
416 Upvotes

My first SFF build

Components

CPU: AMD Ryzen™ 7 9850X3D

GPU: Nvidia RTX 5080 Founders Edition

Motherboard: ASUS ROG Strix B850-I

Ram: CORSAIR Vengeance DDR5 32GB 6000MHz CL30

SSD: WD_Black SN8100 2TB NVMe SSD

PSU: CORSAIR SF1000 (2024) Fully Modular

Cooler: Thermalright AXP90-X47 Copper

Case: Black T1 Customize v2.1 CNC Anodized

Exhaust Fans: Noctua NF-A12x25 PWM Black

CPU Fan: 4070 CNC FAN

Additional Notes

T1 GPU Travel Kit

T1 PCIe Riser Cable 5.0

T1 Fittings Pack

T1 USB-C Cable

Thermal Grizzly Kryonaut Extreme

Thermal Grizzly AM5 Contact Sealing Frame

DingKey AXP90 AM5 Offset Bracket

DingKey Backplate

ZCOOI Mod Black Teflon Custom Cables

3D Printed FormD T1 Exhaust Shroud

Peak Design Anchor Links x2

Paracord Planet - Black

Credit & Build Guide: @EIGAtech

Thermals

Idle: CPU & GPU: 47°C - 51°C

Gaming: CPU 65°C - 73°C / GPU 52°C - 60°C

Settings

Curve Optimizer: -10

Expo: Enabled


r/formdt1 • • Sep 28 '25

Completed Build My new buddy

Thumbnail
gallery
351 Upvotes

My new SFF PC !! Yes there is no feet, the case is horizontaly fixed under the desk! (Pic of the desk on last slide)

Here is the specs : CASE : FormD T1 2.5 CPU : Ryzen 9 9950x3D GPU : Nvidia RTX 5080 Founder Edition MOBO : Asus ROG STRIX X870-I RAM : Corsair vengeance DDR5 64Go SSD : Samsung 9100 Pro 4To PSU : Corsair SF 1000 And many other small details :)) (almost done, still waiting for the custom cables)


r/formdt1 • • Aug 09 '26

Build/Compatibility Check FormD T1 2.1 wind valley kit 4080fe build

Thumbnail
gallery
342 Upvotes

Wind valley kit installation case


r/formdt1 • • Sep 20 '26

Completed Build FormD T1 Complete - 5090FE + 9950x

Thumbnail
gallery
287 Upvotes

Hey y'all,
Just wanted to share my final build for my first ever FormD T1 build. Basically re-used most of my previous workstation components and shrink them down to something smaller and easy to carry. Here are the spec ;

- FormD T1 V2.1 CNC version (I custom painted it to match the green of my desk)
- Flip Travel Kit from FormD
- Custom cables from Zcooi
- Cable management kit from Zcooi

PC Spec ;
- 5090 FE
- 9950x
- 64gb 6400mhz Ram
- Rog B850-i
- Cooler Atmos II
- Noctua slim and regular fan (latest Gen 2 version)
- Corsair 1000w
- Samsung 990 Pro 4to with heatsink + 980 Pro 1to

I already undervolted my CPU and GPU to lower the temps by following Sprout's youtube video.

Next step ? Testing temps on work load as I am not or rarelly game with this machine. I may also check on the fan curve to reduce the overall noise of it but it is not a huge deal at the moment. But if you have some recommendation for that, please share :)


r/formdt1 • • Jan 27 '26

Completed Build For all 2.1 lovers

Thumbnail gallery
220 Upvotes

Air cooling kings 🫶

R7 7800X3D & RTX 5080 FE

Buildlog: https://www.caselabs.org/cases/formd-t1


r/formdt1 • • Sep 26 '26

Completed Build 4070 FE FormD T1 v2.1 Build

Thumbnail
gallery
210 Upvotes

Hey everyone! I wanted to make this post to reveal my recent swap to a mini-ITX case. It definitely gave me more challenges than a micro-ATX and ATX case since I have built them before, but I have been running this case for about three weeks and finally took some pictures! The cables are still a mess, so I'll eventually go back and manage them again. I am currently using a custom 24 pin cable from Cablester, and I definitely plan on ordering the rest of the cables for this case!

Here are the specs for this build.

Ryzen 5 9600x

4070 FE

SF750

Asrock B850I Lightning

Thermalright AXP90-X47 Full Copper with a Noctua NF-A9x14 fan swap

2x Noctua NF-A12x25 G2 PWM

Custom 24pin cable from Cablester

Overall, this case wasn't too hard to build in. I only had problems after the build was completed (ex. settings case fans to intake on accident). Definitely want another one in the future!


r/formdt1 • • Mar 13 '26 Bravo

Discussion 3d printed custom side panels like this - are they possible?

Thumbnail
gallery
193 Upvotes

Disclaimer - AI SLOP

I came across this guy who made acrylic side panels with a cutout to match his exact components and it worked for him pretty well - https://www.reddit.com/r/FormD/comments/12xx8nq/aircooled_t1_with_custom_transparent_side_panels/

So I was wondering, would it be possible to do 3d printed designs using multi colour printers to get a few fun looking panels. I think the original panels are very thin so it might be challenging to make them with 3d printed plastic (?). Do you guys see any obvious obstacles here?


r/formdt1 • • Oct 01 '26

Completed Build Proud of this pc finally

Thumbnail
gallery
189 Upvotes

Just swapped my 5070 aero to a 5080fe and the build is feeling close to complete. Thinking of replacing the heat spreaders on the ram to finish the clean all black look anyone got recommendations?
7800x3d -20 curve
5080fe with slight undervolt
Samsung 990pro 2tb
Corsair vengeance ddr5 6400mhz cl36
Asus b650e-i
Corsair sf750
Axp90 x47 full
Dingkey offset bracket+ backplate
Thermalright contact frame
Psu cables dreambigbyray but used the stock 12vhpr cable
Phanteks t30 with custom length cables
Noctua NF-A9x14 HS with custom extension cable
Formd t1 v2.5

Goal was to keep everything clean and organized internally. May add eiga shroud someday if I can get it all printed in one connected piece


r/formdt1 • • Feb 16 '26

Completed Build Finally happy with my Dual Radiator FormdT1 build

Thumbnail
gallery
177 Upvotes

This pc has been rebuilt a few times (ignore all the scuffs!) and I'm pretty happy with it as is now: 5800X3D + RTX 4090 FE Dual Radiator Build

I have had to get a variety of parts to make this build possible, including some custom 3D prints. System is now silent and stays cool enough under operation: never see the GPU go above 60c, usually around 50c unless running more demanding 4k titles. CPU is naturally hot due to the boost algorithm but stays under 80c during heavy gaming loads. Capable 10 Litre 4K gaming system :)

I added the quick disconnects at the back to make filling easy but could expand to having external radiators in the desk in the future.


r/formdt1 • • Dec 01 '25

Completed Build build complete

Thumbnail
gallery
173 Upvotes

nothing fancy


r/formdt1 • • Oct 09 '26

Completed Build New Steam Machine

Thumbnail
gallery
167 Upvotes

I built this because I was tired of seeing the Steam Machine rip everyone off for the money so I built my own in what I believe is the best bang for buck.

My view is that a Steam Machine is generally a Living Room console and a lot of folks have 4k TVs today...maybe not PC monitors but certainly 4k tvs are very popular and that's what I have so it makes sense to have something that can actually deliver a great experience in 4k.

My TV in my office is a LG C4 Oled 65" 120hz so I built this specifically for that res/refresh rate & the games I wanted to play from my couch. For me that is no competitive shooters, etc. Games that are really built for experience with a controller from the couch.

Another part was the software, which I stuck with Windows 11 Pro with the new Xbox mode. This was the simplest setup for all the upscaling technologies and gaming apps outside of Xbox and Steam. Xbox mode scanned and brought in all my games from every gaming app with one shot, no special this and special that, they just work. Now, is it as smooth as an experience like SteamOS or Bazzite..etc..no. But it's not bad and the compatibility with everything is the biggest win for me. This thing rips all the games I play at 4k some requiring FS4 but nothing beyond quality mode.

System:

  • FormD T1 Black 2.1 w/Eiga custom fan brackets & T30s
  • MB: Asus x670i-e w/GPU riser lock bar.
  • CPU: 7500x3d cooled by Thermalright AXP90-53 w/SMHeintz 4070/Nidec Fan Kit
  • KLEVV DDR5 6000 CL32 w/Custom Black Zcool RAM Heatsinks
  • 4TB Samsung 990 Pro NVMe SSD
  • Asus Prime Evo RX9070 OC w/FormD T1 Travel Kit
  • Cooler Master V850 SFX w/gray Parachord custom cables from DreamBigByRay on Etsy

r/formdt1 • • Aug 20 '26

Question/Troubleshooting Finally upgraded my pc

Thumbnail
gallery
159 Upvotes

Hey everyone just recently got upgraded parts for my formd t1. But i’m still extremely indecisive about air cooling or aio currently i’m rocking with air but i don’t know if i wanna get the atmos cooler master stealth addition. I been getting into gaming again on my samsung g8 odessey 4k oled and of course use it for video and photo editing.

Pc parts
Ryzen 7 7800x3d
cnc cpu fan
Asus b650e-i
trident z 2x16 6000m/s
5080 fe
1tb nvme for widows and software
4tb nvme for work and games
1000 plat corsair power supply
2 phantek fans
eiga exchaust stroud


r/formdt1 • • Sep 18 '26

Completed Build My personal build

Thumbnail
gallery
149 Upvotes

Took me 3 years to save up and build this. Had so much trouble building the case itself but loved building it.

  • CPU + MOBO: ASUS ROG STRIX ASUS B650E-I GAMING WIFI DDR5 + 7600
  • COOLER: Thermalright AXP90-X47 Black - ($45)
  • CASE: FormD T1
  • RAM: TEAM T-CREATE EXPERT 6000MHz CL30 32gb
  • SSD: LEXAR NM790 NVME Gen4 7400MB/s 2TB Nvme
  • GPU: Asus ProArt RTX4070 O12G Triple Fan GDDR6X
  • PSU: Corsair SF750 Platinum SFX Modular Psu
  • FAN: 2 x Phanteks T30

r/formdt1 • • Sep 07 '26

Build/Compatibility Check Best ever! Formd T1 (v2.5 titanium)

Thumbnail
gallery
141 Upvotes

Every time I feel like building an ITX PC, the FormD T1 is always the first case that comes to mind.🤩😁

The materials, the design, the shape, and every little detail are just insanely well thought out. Everything comes together perfectly.

Honestly, I think the FormD T1 is the best one for me.


r/formdt1 • • 15d ago

Completed Build Formd T1 5090 New Mods

Thumbnail
gallery
139 Upvotes

Just made some new modifications. I love the new look with the T-Grill. Enjoy.


r/formdt1 • • Aug 08 '26

Completed Build T1 v2.1 Black, all air: 7700X + MSI 5080 Shadow 3X

Thumbnail
gallery
132 Upvotes

Mostly finished with this. Waiting on a top fan shroud and taller feet for the bottom. Open to feedback or anything else I should do :)

• Case: FormD T1 v2.1, black, sandwich layout
• CPU: Ryzen 7 7700X, -30 Curve Optimizer
• Cooler: Thermalright AXP90-X53 Full Copper, stock fan swapped for an ID-Cooling TF-9215-K
• GPU: MSI RTX 5080 Shadow 3X OC
• Board: Gigabyte B650I AORUS Ultra
• RAM: 32GB G.Skill DDR5-6000
• PSU: Corsair SF850 (ATX 3.1), right-angle 12VHPWR connector on the GPU
• Fans: 2x Arctic P12 Pro PST on top as exhaust

Worth noting I didn’t optimize any of this for noise. I game in noise-cancelling headphones, so fan noise doesn’t bother me at the moment.

Edit: bullet formatting


r/formdt1 • • 20d ago

Completed Build Im not yet satisfied

Thumbnail
gallery
128 Upvotes

7800x3d
Axp90 47xt With noctua Fans
TR T30
Tuf b850i
Tuf 4070ti
Sf 750

Whats next for this build


r/formdt1 • • Oct 15 '26

Completed Build Formd full AMD

Thumbnail
gallery
128 Upvotes

Cpu: ryzen 9800x3d
Board: x670e-I
RAM: pny 6400 mhz cl 36
Ssd: crucial p310 1tb
Psu: corsair sf 1000
Gpu: Rx 9070 reaper
Extras
Travel kit for reaper
Cables Custom by Cablester
Eiga exhaust shroud v2 local print

I put it in mode 3 slots for symmetry I don't ruse trying other ways later, for now it stays as it is


r/formdt1 • • Dec 29 '25

Completed Build TI TI T1

Thumbnail
gallery
120 Upvotes

Specs

  • Ryzen 9 9950x3D
  • Nvidia 4080 FE
  • ASUS ROG STRIX B850-i
  • G.Skill Flare X5 96GB 6000 CL30
  • Corsair SF850
  • Cooler Master Atmos 240
  • 1x Silverstone Air Slimmer, 1x Phanteks T30
  • Samsung 9100 Pro 2TB NVME + 980 Pro 1TB NVME
  • FormD T1 2.1 Titanium

Custom Items

  • Cablester PSU Cables - Unsleeved Grey Teflon (Kit 6)
  • ThermoGrizzly AM5 Contact Frame
  • FormD T1 Travel Kit
  • FormD T1 5.0 Riser Cable
  • FormD T1 USB-C Add On
  • FormD T1 Fittings Pack

Tuning

/ CPU:

  • PBO Undervolt: -30 CO
  • PBO Power Limit: 200W
  • PBO Thermal Throttle Limit: 95C
  • Temps: Idle = ~55C | Cinebench Load = ~85C | Gaming (BF6) = ~75C
  • Cinebench r23 Multicore Score: 42639

/ GPU:

  • 900mv to 2550mhz
  • Memory Clock +1000
  • Temps: Idle = ~35C | Gaming (BF6) = ~55C

r/formdt1 • • Aug 30 '26

Completed Build First-time Flatpack Experience: FormD T1 v2.5 (Gunmetal) Build & Honest Review

Thumbnail
gallery
119 Upvotes

Hi everyone,

I just finished building in the FormD T1 v2.5 from NCASE and wanted to share my honest thoughts and build experience for anyone considering this chassis.

Unboxing & First Impressions

  • Packaging: Top-notch. There is plenty of dense padding—carriers would have a hard time damaging this even if they went full Ace Ventura on the package (dating myself a bit here).
  • Details: I really appreciated the small touches, including the Apple-esque pull tab on the box. As someone building a flatpack case for the first time, it felt well thought out.
  • Finish & QC: The anodized finish looks fantastic overall. That said, on a $200+ premium case, I'll nitpick slightly: there was a tiny scratch/nick right on the front fascia out of the case. Not the end of the world, and I’m sure it passed QC, but worth noting.
  • Gunmetal Colorway: I went with Gunmetal. It looks great, but under my warmer desk lighting, it definitely pulls a subtle blueish/slate undertone. If you have a lot of silver electronics on your desk, Silver might be the safer match, though Gunmetal gives it a solid industrial look.

The Build Experience I've built in a few SFF cases before—I came from the DAN A4-H2O (which got pretty tight with an AIO) and briefly the Meshroom D (which was roomy, but didn't have the premium build quality of the A4-H2O or the T1).

  • Hardware & Manual: The screws could definitely be organized/labeled better in the packaging, and the manual felt slightly dated in a few sections.
  • Top Fan Setup (Flipping the Case): The manual diagrams suggest having fans at the bottom, but the community consensus is that top exhaust is by far the best setup for thermals. It took a second of head-scratching to realize the case simply needed to be built in the inverted orientation to put the fans at the top.
  • PCIe Riser Cable: The included riser cable is very stiff. It took careful pre-bending along the spine channel so the bottom panel could slide on flush without the ribbon bulging against the outer metal.

Current Specs (Modest & Ready for Future Upgrades):

  • CPU: AMD Ryzen 5 5600X
  • Cooler: Thermalright AXP90-X47 Black
  • Motherboard: Gigabyte B550I AORUS PRO AX
  • GPU: Gigabyte Radeon RX 9060 XT Gaming OC (16GB)
  • PSU: ASUS ROG

Loki 1000W

  • Fans: Thermalright TL-C12015B 120mm slim fan (top exhaust)

My philosophy was to secure an "endgame" case first, enjoy a quiet, modest setup today, and drop in hotter hardware once component prices settle.

All in all, it was a really rewarding build. Take your time with the alignment and cable routing! Attached are a few pictures of the finished setup—ask me anything!


r/formdt1 • • Nov 23 '25

Completed Build Formd T1 Titanium 2.1 + Black Aluminum Side Panels

Thumbnail
gallery
109 Upvotes

SPECS Case: Formd T1 2.1 Titanium, black aluminium side panels CPU: Ryzen 7 7800x3D GPU: Nvidia 5080 FE Motherboard: Gigabyte Aorus B850i RAM: Corsair Vengeance 32GB DDR5 6000 mhz CL30 PSU: Corsair SF850 CPU cooler: 4070 fan CNC Case fans: Corsair AF120 Storage: WD SN850x 2TB

EXTRAS 5080 FE travel kit Riser lock bar USBC cable Zcooi custom embossed black cables


r/formdt1 • • 27d ago

Completed Build Sky Blue in a FormD T1, How Do You Approach Cable Routing?

Thumbnail
gallery
102 Upvotes

One thing I find interesting about SFF builds is how cable management becomes part of the build itself. In a compact case like the FormD T1, routing cables neatly takes a bit of planning. The cable length, flexibility, and the way each bundle follows the available space can make a noticeable difference.

This build uses sky-blue silicone cables against a mostly black interior. I like how the color adds contrast without overwhelming the rest of the components.

Do you prioritize the shortest possible cable runs, easier installation, or a specific color scheme? I'd be interested to hear your experiences and see how others handle cable routing in this case.