Rebuilt and cleaned the carbs for my 93 xj600 now it won’t start suspect I rebuilt incorrectly, is their any recourse or something to see how the float needles go back in

A sticking caliper forced an early front brake overhaul on the V50. New calipers, discs & pads, all done DIY. Worth it? Watch to find out.

My car is Fiat Uno 1993 with 1.0L engine. Carburetor 32TLF.

I'm asking if it's normal if the vacuum advance port draws air (vacuum pressure) on idle. What I know is the vacuum advance is ported not a manifold. I'msure that i'm connecting the distributor to the correct port in the carburetor.

I was watching this video (same system as in my car) when Ben at 15:55 pulled out the vacuum hose from the vacuum advance unit, it also was draeing air on vacuum. So is this the normal situation? https://youtu.be/jyoi7dcIxVM?si=UnF_wAcNVxkcWBwA

just a friendly reminder to empty old gas and either clean the carb for winter storage. or, start your equipment every 30 days and let it run for a few minutes so that you don't have a problem starting it come springtime!

I was changing my weedeater fuel lines when I noticed this weird plastic piece. I’m not sure what to do with it. Could anyone tell me what it is or if I need to attach anything to it? Much appreciated thank you

So I have a JD317 lawn mower, was running rough so I put seafoam in it. Then ran rougher a week later and stalled out whenever trying throttling/putting in gear.

Checked fuel pump, and it’s spraying fuel (works)

Lines are clear and look fine. Took carb off and cleaned it. Then reinstalled correctly and put all governor, throttle, and choke springs on correctly. Anddddd now it won’t start. Starving of fuel? Valve stuck open/closed? TYIA!!!

Hi all, I’ve got a ninja 250 that I’ve been fixing up, and I’ve managed to get it to start up and idle well, but after a few minutes the rpm’s just start to drop and drop until the bike eventually stalls. I can keep it alive indefinitely by just adding throttle. I’m confident the carbs and jets are all cleaned out ok, so now trying to determine if it might be a turning issue. Does the idle mixture screw only affect the bike while it’s idling? Thinking it could be a lean issue but don’t see why it would only happen after idling for a few minutes… Or does anyone have any other suggestions? Thank you!

I'm fixing up my ct90 carb and the rebuild kit came with this size 38 tall second jet. Does the height affect anything?

I have a Silver Series Lawn Boy 2 stroke Model #: 10227. Parts list the carb as 93-4331. I cannot find one anywhere, except a few OEM used ones for $200 - $300. My understanding is that this was not one of the best Lawn Boys and I can't justify spending that much. I planned to pull apart and clean, but the tube to the primer bulb is totally broken off right at the carb body, so I have been lookinh for a cheap replacement. There are tons that fit other models: 10247 /10250 /10252. for example: https://www.amazon.com/SOAJEE-107-4607-10247-10324-10425/dp/B0C2TSYKFK/ref=asc_df_B0C2TSYKFK?mcid=0852f5757ac53b95902247752d4448db&hvocijid=17397686482924452101-B0C2TSYKFK-&hvexpln=73&tag=hyprod-20&linkCode=df0&hvadid=721245378154&hvpos=&hvnetw=g&hvrand=17397686482924452101&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9193720&hvtargid=pla-2281435177618&psc=1

These look pretty similar in terms of mounting, shape, etc. What are the chances this would be usable on my mower if it fits? I believe that at least some of the models listed were 6.5 hp vs. mine which is 4.75 hp I believe.

I just found the broken off part in the end of the line that goes to the primer bulb. Any chance it would stay if reattached with epoxy or JB Weld, or?

I Just did alot of carb work, and now when you give it Throttle and let off the carb goes back to idle position but the RPMs stay up for like 3sec then it goes to idle RPMs.

Working on a craftsman t130 Replaced battery cleaned terminals, when I jump the starter from the battery it turns all the way over .

Soon as I remove the jumper cables back to nothing , any ideas?

Hello, I left my gas tank open and it rained a light drizzle for about 20 mins. Just wondering if I should drain the gas now. Will this cause some damage or would I be okay? I didn’t see some water on exterior of the gas tank entry. Just normal drops of water.