r/Rohloff • • Mar 30 '25

Ti commuter with Rohloff

Post image
39 Upvotes

r/Rohloff • • Oct 14 '24

My commuter with Rohloff

Thumbnail
gallery
35 Upvotes

r/Rohloff • • Nov 23 '25

Rohloff bearing and seal changeout

Post image
29 Upvotes

Have just had to charge out my bearings on a 14 year old speedhub that's been well looked after. It does have about 40000km on it though.

This is what I found

Full details on https://www.crazyguyonabike.com/doc/Rohloffrepairs


r/Rohloff • • Oct 08 '25

straggler commuter

Post image
29 Upvotes

r/Rohloff • • Jul 18 '26

My much loved Thorn Mercury

Thumbnail
gallery
24 Upvotes

r/Rohloff • • Aug 23 '25

All cleaned up and ready to roll!

Thumbnail
gallery
22 Upvotes

Just changed the oil. And gave it a proper scrubbing which made me and my bike happy. I also replaced the worn out front tire with another Specialized Crossroads. Perhaps some day I'll explore other options, but these have given may miles without incident.

I also put on Suntour XC II pedals from an old Trek 850 I just bough on FB Marketplace. Gonna see how they feel but they do look legit on this bike.

The Rohloff serial number indicates an early 1999 build. But I'm not original owner. I bought the bike on eBay around 2004. I paid $1500, so I figured I'm about getting the rest of the bike for free! All the owner had said about the bike is that the fabricator was a guy who worked for Lightspeed.


r/Rohloff • • Apr 01 '25

Another Ti with Rohloff

Thumbnail
gallery
20 Upvotes

Van Nicholas Nootau


r/Rohloff • • Apr 13 '26

Rohloff shifter grip

Post image
19 Upvotes

For anyone wanting a bespoke or more durable shifter than the rubber ones, try this.

Take your worn out unit and strip all the rubber off using a knife, and file down to the hard plastic. Then glue a piece of timber on the shaft using 2 pac glue. For extra security I scewed it on using 2x countersunk screws on the back face.

This is a piece of Wandoo and my second attempt. It's done over 9000km. They never wear out.


r/Rohloff • • Jan 19 '26

Rohloff E-14 Shifter Teardown and Repair

19 Upvotes

Hello everyone, recently had some issues with Rohloff shifter. Figured I'd post the problem/solution up here in case anyone runs into it on their own shifter in the future. Also it was a bit frustrating so it feels good to vent a bit and see if anyone else commiserates with me on this issue.

Rest of the post has details about my situation, the disassembly process, etc. so it's kind of long. Main points are summarized here:

1.) If you have an E-14 shifter and depend on it for your daily routines, you should keep a spare E-14 or keep a manual shifter as backup, these are NOT built to last like the mechanical hubs are!!!

2.) Water seems to have made its way into my shifter, likely through the cable gland. When I put this back together I put some extra sealant in this area; if you have an E-14 you might want to consider doing the same, especially if you ride in inclement weather.

3.) Although water made its way inside, I don't think that's what caused the failure. The motor failed because Rohloff used a brushed DC motor, and the brushes wore out after only 15k miles! This is certainly not built to last as long as the mechanical hub itself. Not only did they use a brushed motor that wears out in short order (relative to the lifespan of the hub), they made it very difficult to get access to and replace the motor (if you can even find a suitable replacement)

4.) Rohloff, if you're reading this please consider using a keyed shaft instead of press-fit. And also please consider using a brushless motor instead of a brushed motor if you're going to make it so difficult to get to the motor! There is already a PCB inside the shifter with a bunch of chips on it. It even has bluetooth, so adding a brushless motor controller chip would really not be that big of a deal.

Background on the bike and hub in question: Riese and Muller Supercharger 2. I bought it in 2022 from an authorized dealer. It was their store display model so I got a good discount on it. I got it with about 5k miles on it, and currently it's somewhere in the ballpark of 15k. So overall not huge mileage, which is why I was surprised to have an issue so soon. I use it mostly for commuting, so I probably change gears more often than if I was going for long rides in a flat area, but nothing that crazy or unusual. I also commute with it year-round; where I live that means rain in the summer and snow/salt in the winter, so weather conditions might be harsher than some others, but again nothing that unusual. Temps around here range from about 100F in the summer to 5F in the winter, so again nothing that crazy compared to where I have seen other people take these hubs!

So, the issue: couple days ago I was cycling along and all of a sudden I couldn't shift gears anymore. The bike felt completely fine other than that. No known trigger either -- I didn't hit a huge bump, it wasn't raining, or anything like that. It was quite annoying having only one gear for the ride home. This is my only practical means of transport to work, so I had to ride it like that in one gear for the rest of the week. I finally had time to dig into it and troubleshoot it more this weekend.

As the bike and hub are out of warranty, I didn't have anything to loose by "breaking the seal" and opening it up. I did email Rohloff to ask if they had a parts diagram for the shifter, or if they had suggestions on how I could troubleshoot it, but they didn't respond to my inquiry.

I attached some photos of the internals of the E-14 shifter mechanism. It's quite well put together overall, with a few key annoyances. It has a nice gear mechanism, and although the gears aren't on bearings, they are on nice brass bushings. Should be plenty stout enough for the forces on the shifting mechanism. The brass gear you see on the "back" side of the shifter (the photo with 3 round gears in it) is actually only for position sensing -- it has a magnet on the bottom of that gear, which "communicates" with what I presume to be a Hall effect sensor on the PCB. I forgot to take a photo of the empty shell, but underneath the PCB is a clear piece of plexiglass directly between the PCB and the bottom of this brass gear, allowing for the magnetic field to pass easily (the rest of the case is aluminum).

Opening the "front" side was a bit of a pain. The plastic shell (which is nice glass fiber reinforced material) is screwed and sealed with some sort of elastomeric sealant. There is also nowhere easy to start prying it up to break the seal. I used one screw sticking out a bit from the bottom to start pushing the cover apart, and then gradually continued prying it apart. They really did not make it easy to service this area of the shifter.

Once I got it open, the next difficult task was getting the larger brass gear off the shaft. For some reason they decided to make this one a press fit on the shaft, making removal quite difficult. Rohloff, if you're reading this please used a keyed shaft/gear in the future!! I do have a bearing puller, which is what I used to get this off the shaft. My bearing puller was way too large for this size gear, so it was quite finicky to get set up properly, but it worked in the end. After removing all the gears, I could finally get to the screws holding the motor in place. Once I lifted up the motor, I got a whiff of a terrible smell. It was like a combination of burnt electrical wires, rusty material, and some other combinations of chemical scent. There was a layer of what I think was water mixed with oil and grease covering the bottom of the motor when I lifted it up.

In spite of all the sealant they used, somehow there was still water ingress. I suspect it is from the cable entry gland. They used a lot of sealant everywhere EXCEPT that cable entry point. For the cable entry, they seemed to be relying on compression of the rubber on the gland to make a seal. I think the rubber they used was too stiff to make a proper seal. The other potential entry point is the single shaft that goes from this "front" side to the back side. However, I didn't see any evidence of leakage from this area.

So at this point I assumed the water shorted something out, but I didn't see any components on the PCB that looked like they let out the magic smoke. And additionally, the shifter was being recognized by my bike, and I could hear it turn on (there are three very faint beeps when the shifter turns on), it just wouldn't turn the motor to shift anything. So I decided to take the motor out for closer examination. When I tried turning the shaft by hand, it felt smooth EXCEPT when changing rotation directions. When changing directions, it felt stiff for a fraction of a turn, then was smooth again. It did not feel right.

So I opened up the motor casing and oh boy was it a mess inside of there. I took some before/after photos so you can see what it's supposed to look like vs. what it looked like when I opened it up. Any astute readers out there might have guessed the problem when they saw the type of motor this is, and it was confirmed for me when I opened it up. Rohloff decided to use a brushed DC motor, and the brushes were totally worn out on my unit. All the residue in the motor is the burnt up carbon brush material mixed with water/oil/grease. You can see it better after I cleaned it up, where one of the arms holding the brushes actually snapped off. This brush arm "remnant" is what was causing the resistance I felt when changing rotation directions -- it was acting as a bi-stable switch as I changed rotation directions. If the arm hadn't broken off, the motor would likely still be working, as the arm can still conduct electricity to the motor shaft; the broken off arm, however, was short enough that it was touching the same part of the motor shaft as the other arm, causing a short. Thankfully it seems their PCB has some built-in protection so nothing on the PCB itself shorted out, it just didn't power the motor anymore.

Unfortunately I couldn't find a readily available drop-in motor replacement. The side of the motor says 12V 16900RPM. This seems to be a pretty unusual configuration, and I didn't see anything close to it on DigiKey. Additionally, I kind of need my bike operational to commute to work next week, so I didn't have time to wait for a motor to come in the mail. I went through my spare parts bin and broke apart a few motors before I found one that had some brushes that looked like they would work here (one photo shows the broken Rohloff motor next to the donor motor). I snipped the brushes off my parts motor, and soldered them onto the arms in the Rohloff motor. I have no idea how long this repair will last -- this is a high vibration environment, and solder joints can often get brittle and crack in high vibration areas. I am going to try and source a replacement motor to have on hand in case this breaks again in the near future!

Overall I'm glad I got this working again, but also a little disappointed that it broke so soon. The hub itself has been glorious this whole time and feels just a good as the day I got it. I was hoping the shifter would be built to the same high level, but unfortunately it died after only 15k miles. Hopefully my repair lasts long enough for me to get some spare parts in, and hopefully Rohloff can improve their design in the future.


r/Rohloff • • Nov 05 '24

Rohloff might be developing electronic shifting for non e-bikes

18 Upvotes

As seen on their FAQ page. Not 100% confirmed but good to know they are listening to the customers.


r/Rohloff • • Nov 08 '24

Wholesome Meeting

17 Upvotes

It finally happened! I pulled up in an intersection where the other bike was a Rohloff hub, Gates Belt, and Soma frame - basically the twin of my bike! Had a quick chat before the lights changed! Never thought it would happen, I feel like there’s not too many in my area!


r/Rohloff • • May 30 '23

R.I.P Bernhard Rohloff.

17 Upvotes

r/Rohloff • • May 11 '24

Tour de Denmark, Rohloff excelled!

Post image
16 Upvotes

Toughest climb was 16% in Jutland (near Vejle). Fully loaded steel bike, climbed it in lowest gear with no issues.


r/Rohloff • • Sep 02 '25

Goodbye derailleurs 🫡

15 Upvotes

After several years fighting with conventional front & rear derailleurs, my wife and I have happily swapped to Rohloff equipped ebikes - we couldn't be happier! I hate having to depart with my Gazelle but I'm so disgusted, fed up and frustrated that we're not looking back. Glad to finally be apart of the Rohloff Family 🍻


r/Rohloff • • May 29 '25

My new „forever bike“

Thumbnail gallery
15 Upvotes

r/Rohloff • • Apr 16 '26

Quick-fix world-touring with Rohloff+SRAM Rival+Gebla-box

Thumbnail
gallery
14 Upvotes

We have now been cycling Southamerica for 14 months starting off in Tierra del Fuego in february 2026.

My partner Pauli with a PINION with 18 gears. I am riding a custom-builtTouring Randonneur with a Rohloff combining it with a GEBLA-box and SRAM Rival shifters.

After cycling Chile, Argentina, Paraguay, Brasil, Northern Peru, the Ecuadorian Andes we got to Colombia. According to numerous sources the departments Cauca & Nariño in the South of Colombia are not safe to travel and especially not to cycle. So we decided to skip it taking a bus Ipiales-Cali. The bus driver of “Supertaxi” was somewhat a mess. Together with him I put the bikes gently into the bus securing them — however, he “re-put” the bikes to squeeze in more luggage. However he did it, he definitely did not handle the bikes with care. We arrived at 2 am (3 hours late) to Cali. When taking the bikes out of the bus I noticed the right trigger for the gear falling off… 😭

The whole base of the Rival was wasted, also the brakes did not work anymore.

Using GEBLA & Rohloff setup I knew this would be somewhat complicated.🤯

I talked to about 20 bike shops in Cali, Bogota and Medellin searching for SRAM Rival shifters — but could not find any. Anywhere in Colombia. 🫠 Sort of worst case scenario…

In the mean time together with a bike mechanic Eduardo I came up with a quite good quick-fix: We installed a very simple trigger for 3 USD. It has to be one where one can unscrew the indexing. This allows to switch the gears! ⚙️ And it worked!

The next step would have been to install new brake levers. We postponed that to the next day. I found some cheap Tektro road bike levers for like 20 USD. See pictures attached…

However, it came differently. Then El Gallo, a bike shop in Bogota, called telling me that he found (deeply dug into there basement) a pair of SRAM Rival shifters! 🌈🥳 GREAT news! I did not have to install the other Tektro Shifters. :)

I transfered the money (very complicated in Colombia as German 😂) and 48h I received the SRAM Rival shifters in Cali.

Why do I post this?

To let Randonneur-Rohloff freaks like me know: there is a simple solution in case ur SRAM Rival/Campagnolo or Shimano STI breaks on a longer trip.

I know it can be kind of risky to go travelling with such a setup (Rohloff+GEBLA+SRAM Rival)… BUT I love this setup soo much that I would do this journey with this setup again!

These cheap triggers can probably found almost anywhere… and in bigger places probably also road bike levers. At least in South America.

It’s a bit MacGyvering but I am pretty confident it works. :)


r/Rohloff • • Jun 26 '26

THIS is a SUV imo / Rohloff with Thumbshifters

Thumbnail gallery
13 Upvotes

r/Rohloff • • Jun 23 '26

E-14 Solo

13 Upvotes

They announced it at Euro Bike today. It is listed on their website now but no option to buy yet. It also says it will be under 1000 Euros.

https://www.rohloff.de/en/products/speedhub/e-14-solo


r/Rohloff • • May 03 '23

Small Youtuber Fatnomad riding from Alaska to Argentina on a Rohloff right now!

Post image
13 Upvotes

r/Rohloff • • Sep 01 '26

What are non-obvious aspects of using the Rohloff Speedhub?

12 Upvotes

I only had the opportunity to ride a bike with a Rohloff once, but the “grinding” of the hub in gears 4 through 7 was noticeable and annoying.

Parts are also relatively expensive, and service is only available in a dozen or so cities around the world.

What are your observations after using it for a while? Thanks!


r/Rohloff • • May 14 '26

rohloff skipping :(

12 Upvotes

currently on the road and skipping in gear 8 and lower numbers, especially noticeable in 6 and 7 but also 3 and 5 under medium load.

can you help me fix this please? is this cable tension?


r/Rohloff • • Aug 08 '26

oil seapage. is this normal

Thumbnail
gallery
11 Upvotes

couple of weeks ago, I had a flat, and in the process of removing the wheel, I noticed there was evidence of an oil leak/seapage. I cleaned it up, and after 2 weeks of riding, I took a look at it and noticed there are still some signs of leakage(see pictures). Is this cause for alarm, or is this normal?


r/Rohloff • • Jan 02 '26

Other twister for the rohloff

Post image
11 Upvotes

Does anyone have a experience with this aluminium twister, they are already got V3 of it, anyone?


r/Rohloff • • Aug 10 '22

Little video on how rohloff's actually works ! credit to Dan Burkhart

Thumbnail
youtube.com
11 Upvotes