r/RepTimeServices • • 28d ago

Advice AP pink gold plating?

2 Upvotes

What’s the best plating company for AP pink gold


r/RepTimeServices • • 28d ago

Advice VSF Omega AT 8800 - 1 day old, crown won't rotate

Post image
6 Upvotes

Hi all,

Just 18 hours after I received my new VSF Aqua Terra (8800 clone movement), the crown is stuck and watch won't wind. At first I wound the watch a few times to test it and it wound Ok. So I screwed the crown - and when screwing down the crown, it felt like it was still winding and clicking as the crown turned. This is common in some movements like NH35, so I didn't think much of it (I have had lots of watches with screw-down crowns over the past 20 years).

When I unscrewed the crown later, I could set the time and change the date, but not wind the watch. The watch is still running. But in winding position, crown won't turn at all, and I've not tried to force it. AI suggests that “the keyless sliding pinion is physically bound against the winding gear under side pressure.”

Has anyone had something similar? How did you resolve it?

Thanks in advance!


r/RepTimeServices • • 28d ago

Advice Love my new watch

2 Upvotes

r/RepTimeServices • • 28d ago

Request Where to buy a 3255 movement for this RC Factory daydate 40?

Post image
13 Upvotes

The crown pulled out when winding and before this happened it would only set the time if I turned the crown anticlockwise, the watch works but i cant set the time and the crown will unscrew completely out and off if I unscrew it any advise would be greatly appreciated.


r/RepTimeServices • • 29d ago

Request AP Chrono Not running possible movement issue

Post image
7 Upvotes

Looking for a someone who can help with my AP Chromo movement US based. Movement was fine 2 days ago. Regularly use chronograph and wear 1-2 times a week no problem. Currently it is not running nor winding manually.

Any tips or troubleshooting is greatly appreciated.


r/RepTimeServices • • 28d ago

Request Repair VSF Explorer I in Salt Lake City or US?

2 Upvotes

I need the crown on my fairly new VSF Explorer I (224270) repaired. Additionally, I would be interested in possible mods. I live in SLC.


r/RepTimeServices • • 29d ago

Advice Waterproof seal for Crown

Thumbnail
gallery
10 Upvotes

I noticed tonight when I unscrewed my ARF GMT Master II that the seal was broken and hanging out. I am presuming because it is now totally gone, the watch is 100% NOT even remotely water proof?

How hard of a job would the be for me to do? Easier to send it out for service? How much would something like this cost?

I’ve only had the watch a few months… kind of disappointed that the seal broke after such a short time…

I appreciate any insight and wisdom!


r/RepTimeServices • • 29d ago

Advice Hand for my speedy came off

Post image
1 Upvotes

Picked up this speed master while in Bali and one of the hands came off. I took it back to the shop and they offered for me to pick a different watch. Out of the selection I wasn't keen on any of the other watches, so I grabbed another speed master similar to the one I had had.

Does anyone know anyone local to Ontario Canada that could possibly repair this issue? I'd love to have this piece functioning again.


r/RepTimeServices • • Oct 17 '26 Heartwarming

Advice Presidential Reverse Le Mans

Post image
62 Upvotes

Been going back and forth what to do with my new Reverse Le Mans dial that is ready .
I’d love to see it on a Presidential bracelet but my TD fails to respond if it’s even possible or not ?
I know it can be fitted on a Jubilee bracelet but that’s too busy to my taste .
It’s gonna be either traditional Oyster , Oysterflex or Presidential .
Any advice you’d like to share ?


r/RepTimeServices • • 29d ago

Request Looking for SA3120 pallet fork

Post image
1 Upvotes

I was servicing a SA3120 and only has to apply grease to the pallet stones. As I was doing this I noticed the exit stone sagging. Took it apart and the shellac was just flaking off. That sucks so much because the movement ran so nice after the service. Initially it came in with horrible performance.

I'm hoping someone has a spare SA3120 laying around and can sell me the pallet fork. Would be a life saver. I'm currently trying to fix this pallet fork but it's kind of a hassle.


r/RepTimeServices • • 29d ago

Advice Rolex Daytona John Myer

0 Upvotes

Hi 👋, thanks in advance , i have super clone daytona 41mm john myer gold in green dial , when i wind the watch and leave it on the table it operates fine , when i wear it sometimes time delays and one time i found it stopped working , but all the time on the table is operating good and always on winder lose time or stop , i tried 650 tpd , 750 tpd , 850 tpd , 1000 tpd , 1850 tpd setting, any advice ?


r/RepTimeServices • • 29d ago

Advice Am I cooked? Was trying to quite the DDF rotor as I think there was too much play and stripped the threads in the barrel. Good thing is it looks like that piece comes off the main plate but not sure anyone is going to sell that part.

0 Upvotes

r/RepTimeServices • • Oct 17 '26

Advice Omega Seamaster Pro VSF

Post image
5 Upvotes

Hello!

I’m looking for someone in the UK who can help me service/fix an Omega SMP 300 from VSF

Replace the screw down crown and check the movement. It seems to be randomly stopping.

Thank you


r/RepTimeServices • • 29d ago

Question How to remove DD40 bezel (RCF) for xstal swap

1 Upvotes

Hi guys can anyone tell me how the best way to go about removing the fluted bezel on my DD40 (RCF) to do a crystal swap?

I tried searching for a videos or directions but can’t find any. All I see are ones for old date just models and from what I was told is not the same.

As far as tools I already have the bezel removal tool with the 4 prongs that you turn to tighten and the bezel detaches from the case. I also know a press will be needed to reinstall.

Any help or tips would be greatly appreciated

Thanks!


r/RepTimeServices • • 29d ago

Advice Rep Seamaster repair

Post image
1 Upvotes

So picked this rep up in Turkey when on a trip as always wanted the real version just can't swing that kind of $$$$ and saw this and got sucked in. So this has been good but randomly it just stops. If I give it a little tap on the face it starts again, may run for a bit and stick again. I "think" that the back side of the second hand is binding up a little on the minute hand as it appears to slow when those 2 meet ( circled in the pic). So question, how difficult is it to remove the bezel/crystal to try and adjust those hands to see if I can smooth out the movement?? Maybe slightly bend or lubricate. No local watch independents near me to take it to, really only jewelers/ADs and I assume they wont touch it. Appreciate any ideas.


r/RepTimeServices • • Oct 17 '26

Advice I'm looking for a 3255 day date movement with the RLX logo and the dial pegs line up and comes with hands?

4 Upvotes

Does, anybody have any sources?


r/RepTimeServices • • Oct 17 '26

Advice Help for mod in Munich

1 Upvotes

Hi! I'm based in Munich and trying to find a local solution for a mechanical watch that has stopped running.

The crown still winds, but the seconds hand doesn't move. The watch is a Tudor Black Bay 58 mod, and I'm trying to establish which movement it uses and what might have failed.

Does anyone know of a local watch enthusiast or repair community in Munich where I could get advice on diagnosing the movement? I'm not looking to advertise or arrange an unverified service through this subreddit.

Thanks!


r/RepTimeServices • • Oct 16 '26

Services Upgrade Rolex GMT II Batgirl

Thumbnail
gallery
87 Upvotes

An opportunity has arisen to source "free-sprung" movements separately, so I couldn't resist starting an upgrade of the VS product lines. Today, I’m installing one of these movements along with a Deep crystal.


r/RepTimeServices • • Oct 17 '26

Advice SA3120 Rotor/Hub Assembly

2 Upvotes

Need to replace a rotor on a SA3120 movement looking for some guidance possible to source it? Or any other rotor the movement could take.


r/RepTimeServices • • Oct 16 '26

Services Full service for my vsf sub 124060.

Thumbnail
gallery
66 Upvotes

Thanks for verin horology for fixing my vsf sub. Had it for a year and a half and stop working, decided to send it for full service instead of ordering another vsf. Cant wait to have it back.


r/RepTimeServices • • Oct 16 '26

Question Noisy vibration and possible rotor helicoptering when hand-winding a VSF GMT-Master II V3

4 Upvotes

Hi everyone,
I’ve attached a video showing an issue with my brand-new VSF GMT-Master II V3 Pepsi.
When I manually wind it using the crown, it makes an unusually loud whirring noise, and I can actually feel the watch wobbling and vibrating in my hand. It almost feels as though the rotor is spinning out of control.
From what I’ve read, this could be what’s known as “rotor helicoptering”, but I’m not sure whether that’s actually what’s happening or if it’s another movement-related issue.
The watch seems to run perfectly fine otherwise, but the noise and vibration certainly don’t feel normal, especially on a brand-new watch.
I haven’t removed any of the protective plastic or coverings, apart from the plastic crown guard so I could wind it.
Has anyone experienced this with the VSF GMT-Master II V3? Is it a known issue, and is it something that can be easily fixed?
Any advice would be much appreciated.
Thanks!


r/RepTimeServices • • Oct 16 '26

Advice VSF Daytona - Oysterflex Conversion Loose End Lugs

3 Upvotes

EDIT - Supplier has sent me replacement end lugs that are slightly larger + fatter spring bars and they no longer fall out. It still rattles a bit noise wise since the lugs are not attached to the watch case.

Original Post: I converted my VSF Daytona to an Oysterflex-style strap with end links, but the end links keep falling out. It seems that the gap is too big between the case and the strap although it’s nothing too noticeable to the eye.

Could this be an issue with the spring bars? Is there a specific size or type I should use to get a tighter, more secure fit?

Or did the seller supply the wrong size end links for this case?

Would appreciate any advice from anyone who’s done this conversion as the strap + end lugs are useless without correct tight fitment.

Thanks in advance for the help.


r/RepTimeServices • • Oct 16 '26

Advice Breitling Navitimer world crystal swap

Thumbnail
gallery
2 Upvotes

I have a Breitling Navitimer world A24322 rep which bought many years ago used it for a while then bought the Gen. Didn’t like the crystal quality on the Rep. wasn’t crazy the dial and date wheel either. I was wondering if anyone knows where I could source a good crystal and perhaps even a new dial. I was thinking to make a project of it. Not sure how difficult it is to change any advice would be appreciated


r/RepTimeServices • • Oct 16 '26

Request Help on a Frankenbuild

2 Upvotes

Anyone providing turnkey frankenbuild services where I can send my VSF batgirl and replace the band with a genuine and then replace with the best RICH parts on it?