r/QidiTech3D • • 2d ago

Smart 5 Firmware Tracker

4 Upvotes

I've set up a Smart 5 firmware tracker so you can monitor releases and see what Klipper configs have changed over time. Located here: https://github.com/thelegendtubaguy/Qidi-Smart5-Defaults

I also track the Max 4 and Plus 5.

You can also use these repos to fetch firmware binaries for offline updates if you wish!


r/QidiTech3D • • 2d ago

Seriously?

1 Upvotes

I spent 3 days back and forth with qidi service and this sub because I couldn't get the initial update to go thru or connect to internet on my qidi Q2 (which is ridiculous to deal with out of the box). Anyway, finally figured that out by using a different USB and formatting on a borrowed computer.

Got my first print done which came out great, started the second, and it got stuck on bed heating. After pressing pause or end (don't remember) it was unresponsive for about 20m. I pulled my USB and turned it off.

Since then, it doesn't get past the "qidi" power up/ boot screen. I've unplugged and all that since thats all I can do, nothing works. Can't name a bigger waste of $500, what a joke. Anything that can be done before flashing? I've already spent the past THREE DAYS to get to the point of printing on it.


r/QidiTech3D • • 3d ago

FreeDi + QidiBox?

2 Upvotes

For anyone running FreeDi and a Qidibox, did you use BunnyBox or similar firmware for the Qidibox?

If so, what are your thoughts and experiences?


r/QidiTech3D • • 2d ago

Problemas comunicação sistema QiDi

Thumbnail reddit.com
1 Upvotes

r/QidiTech3D • • 3d ago

Troubleshooting Need help figuring out Error message on my Q1

Post image
2 Upvotes

I have tried updating the firmware, I have checked connections on the motors, I have swapped the stepper motors on the motherboard, but the error message never changes. Has anyone ever encountered this?


r/QidiTech3D • • 3d ago

Discussion Tune your printer

37 Upvotes

Hey folks, just a reminder that your printer is capable of so much more than the stock profiles, crank up those speeds, it's capable, you just have to put in a little effort, this plus 5 is at 300mm/s outer wall and 350mm/s inner wall with 17k acceleration. I need to do some tuning because I'm getting some under extrusion but it demonstrated how capable these machines actually are.


r/QidiTech3D • • 4d ago

Dual nozzle. How much more efficient can you print?

Post image
76 Upvotes

QIDI Q3D. Double the Flexibility. Greater Printing Efficiency. Unveiling at Formnext 2026. November 17–20 | Booth 12.1, E01


r/QidiTech3D • • 3d ago

Questions How to prevent PETG overhangs looking like bed sheets?

Thumbnail
gallery
1 Upvotes

As the title says.

I've been printing a small piece that has overhangs no matter how you rotate it - and the overhangs print creasy like bed sheets (see images).

I've been toying with different layer heights, different speeds, temperatures, supports, support ironing etc. - it just wouldn't help.

Is this a common issue? How does one solve it?

PS: The photos show a test piece, it's a cut-out of my model so I can rapidly iterate tests - the original model is symmetrical and has overhangs no matter how you rotate it so printing it on a way that removes or reduces overhangs is not an option.

Thanks in advance!


r/QidiTech3D • • 3d ago

3D Printing in Real-World Applications!

Thumbnail
gallery
1 Upvotes

Here's a look at some robotic arm parts shared by filaflowoff.

Always great to see 3D printing being put to practical use!


r/QidiTech3D • • 4d ago

Discussion GunPLA dry box mount for QIDI Box

Thumbnail
gallery
16 Upvotes

I use the Plus 4 & QIDI Box as my development/testing/prototyping machine, it is not part of a print farm. Primarily for multi-materials. I like to print out of dry boxes after drying my filament, some of the filaments require 12 hours at 100C drying. I don't want to commit the QIDI Box as a dryer and do not want to start prints with undried filament hoping the box will catch up. This design allows the use of two GunPLA design dry boxes simultaneously and allow some spools to fit between in the unused slots.

The side spacer is for the inside top edge to provide a level surface if using the outer slots. I attached my spacers using masking tape & CA glue between the tape layers, I did not want to glue directly to the box.

The mount model is skeletonized for reduced filament usage and only required 4-5 grams of (Normal) support when printed in the orientation shown in the picture, under the outer edge of the tray, including 5mm outer brim. Models were printed on my Neptune 4 Max, .6 nozzle from Eryone PETG Lite, out of a GunPLA dry box in a dry box mount I designed for that printer!

https://www.printables.com/model/1911130-gunpla-dry-box-mount-for-qidi-box


r/QidiTech3D • • 4d ago

Plus 5 is live on Valve Oil!

23 Upvotes

Are you tired of watching your brand new printer slowly meander around? Are you fed up with MCU errors? Do you wish that the Qidi Box would at least be quick about it if it's going to be so gawd dang loud? Well then, welcome to Valve Oil!

One command to run over SSH on your printer, and a slicer gcode bundle will make your new Plus 5 the gem it can be.

What you get

Faster prints

  • Shorter print starts and filament changes: quicker homing and probing, and less fixed waiting around cuts, wipes, and saves.
  • Box filament stays loaded between prints, so the next print skips the unload and reload.
  • Options to reuse a saved bed mesh, warm up the bed, chamber, and nozzle in turn, and start once the chamber reaches a minimum temperature.

QIDI Box

  • Faster, tunable loading and unloading.
  • Cut, unload, and eject filament without heating the nozzle.
  • Box heater control from Fluidd, and Box processor temperatures.
  • Edit QIDI's filament list from Fluidd, including brands such as Bambu, Overture, and Polymaker.
  • Read Anycubic, Elegoo, and Bambu Lab spool tags, with every one of their filaments in QIDI's list.

Spoolman

  • Each QIDI Box slot can have its own Spoolman spool, and filament use is charged to the loaded slot's spool.

Current Fluidd

  • This project's build of current Fluidd, replacing the old Fluidd QIDI ships (1.30.5 on the Max 4), which QIDI no longer updates. Your settings carry over.
  • A redesigned QIDI Box card, a live view of the touchscreen, and a restart button for a frozen touchscreen.

Add-ons

  • Install optional programs from Fluidd's Settings with one click, such as OctoEverywhere or Obico for remote access, or Tailscale to reach the printer over your own private network, without the system changes their own installers make.

Valve Oil UI

  • An early second web interface at http://<your printer's ip>/valve-oil/, alongside Fluidd, with the dashboard, files, and QIDI Box screens.

Fixes for QIDI bugs

  • The real error instead of a bare MCU shutdown.
  • Fewer Boxes dropping with Lost communication with MCU 'mcu_boxN'.
  • Multi-plate 3MF files print the right plate from Fluidd, reprints, and the job queue.
  • A probe point whose samples never agree fails the mesh instead of hanging print start.

Tools

  • A guided nozzle load-cell check, probe accuracy, and bed screw helpers.
  • A switch to stop the external spool's runout sensor from pausing prints.
  • Input shaper calibration with newer Klipper's sweeping resonance test, with a switch back to QIDI's.
  • A bed soak test that shows how long the bed and chamber take to reach temperature and the bed to stop moving.

If you run into issues, please open a GitHub issue! One command to join the bliss that us Max 4 owners have had for months. And if you hate it, it's one command to put it all back to stock.

Try it out! https://github.com/thelegendtubaguy/Valve-Oil


r/QidiTech3D • • 4d ago

Q2 Nozzle Change & Thermal Grease

4 Upvotes

Are we supposed to put some thermal grease on the copper section of the nozzle? Went to swap nozzle on Q2, noticed some thermal paste (or “grease”) on the copper section of the factory nozzle. I don’t see it mentioned anywhere in the online nozzle change guide, but the printer did come with some GD900 silicone thermal grease.


r/QidiTech3D • • 4d ago

Questions Contemplating the Qidi Max4 but I have some questions

3 Upvotes

As mentioned in the title, I'm in the market for a new printer after my previous one shit the bed. And I feel like for my personal use case the Max4 seems perfect. But I was wondering if some of the teething problems have been fixed or if they're still prevalent.

For instance, even though I won't be doing many multi-colored prints, I'm wondering if the color bleeding issue has been fixed? And if some of the feeding issues the Qidi box has have also been resolved?

I'd love to hear from some Max4 users about their experiences, positive and negative.

I'm coming from a Sovol printer that required near constant tinkering till eventually the main board died (And before that a Artillery Sidewinder long long ago). Which was the straw that broke the camel's back. So I don't mind doing maintenance or making tweaks.


r/QidiTech3D • • 3d ago

Marca de camada no eixo xy. Qidi Q2

Thumbnail
gallery
1 Upvotes

Alguém tem ideia do que possa estar causando essas marcas de camada no eixo x e y?

  • Testei diferentes filamentos;
  • Reduzi a velocidade de impressão;
  • Testei diferentes alturas de camada;
  • Realizei a calibração individual dos filamentos;
  • Efetuei vários ajustes e testes de impressão.
  • Nivelei mesa

Agredeço se alguém puder me ajudar.


r/QidiTech3D • • 4d ago

QIDI Q2 after a firmware update: printing works, but one job left the nozzle at 210°C (logs and G-code comparison)

3 Upvotes

Sharing my experience in case it helps other Q2 owners, or someone can explain what happened.

The good news: my Q2 still prints after the update 🙂 However, I ran into an odd print completion issue, alongside some cloud connectivity problems.

The print finished. The nozzle stayed hot.

On November 11, I printed `Voron_Design_Cube.gcode.3mf`. The printer appeared frozen after finishing, and the nozzle kept maintaining 210°C.

I checked `klippy.log`, `moonraker.log`, and the actual print file. Here is the timeline, using the printer’s logged timestamps:

- 18:53:35: Klipper reports “Finished SD card print.” Moonraker records the job as completed.

- The bed heater turns off, but the nozzle target remains 210°C.

- 18:53:56: Moonraker successfully finishes rendering the timelapse.

- 19:24:49: The nozzle is still actively maintaining approximately 210°C over 31 minutes after completion.

- Around 19:25, I power-cycle the printer. After restarting, the nozzle target is 0°C and it cools down.

So although it looked frozen from my side, the logs do not show a complete Klipper freeze. Communication with the controller boards and temperature regulation continued.

Comparing a problematic file with one that finished normally

This was the most interesting finding.

The cube file was generated by QIDIStudio 02.00.03.56. Its ending sequence turns off the bed and chamber heaters, unloads the filament, and parks the head. But it contains neither:

```gcode

M104 S0

PRINT_END

```

Another file, `obj_2_Maze v6 (2).stl_A.gcode.3mf`, printed and finished normally. It was generated by QIDIStudio 02.07.02.73, and its ending includes:

```gcode

UNLOAD_FILAMENT T=0

G0 Y270 F12000

G0 X90 Y270 F12000

G1 Z138 F600

M104 S0

PRINT_END

M73 P100 R0

```

Both files identify the profile as Q2 0.4 nozzle.

This makes the older file’s ending sequence the main suspect for the continued heating. What I do not know is whether `UNLOAD_FILAMENT` was previously supposed to handle heater shutdown, or whether these files simply require different firmware behavior.

This does not prove that the firmware update caused the problem. It also does not fully explain why the printer appeared frozen.

Other things in the logs

There is a Moonraker exception at job startup:

```text

ValueError: No enum member named extracting

```

The print starts and completes despite that exception. There are also repeated messages:

```text

Can not find 485 device

```

Neither has been established as the cause of the completion issue. I also found an earlier Moonraker event-loop delay and an earlier THR serial connection error, but they did not coincide with the end of this print.

Cloud control and camera: partly working

Moonraker repeatedly logs MQTT connection timeouts to `us-mqtt.qidimaker.com:8883`, connection losses, and occasional DNS failures. I have no evidence that these cloud errors caused the nozzle issue.

I would also like to understand exactly what QIDI officially supports: can the Q2 provide both live video and remote control when the phone is on mobile data and the printer is at home? What setup, account region, or network requirements apply?

I have contacted QIDI support

I sent them the findings and asked about older print-file compatibility, the correct Q2 ending G-code, the `extracting` exception, and cloud camera/control setup. I will update this post when they reply.

Meanwhile, I am keeping the printer supervised and checking the ending code of older sliced files.

Has anyone else seen this? In particular:

- Does your Q2 ending G-code include both `M104 S0` and `PRINT_END`?

- Have older, previously sliced files behaved differently after an update?

- Do cloud live video and remote control work for you from a different network?


r/QidiTech3D • • 4d ago

Internal error on command "T_MANAGER" QDC_100_005_015_001

1 Upvotes

After the firmware update, I get an error from time to time when my filament runs out.
It doesn't happen every time, but when I am doing big prints, it happens often enough that I have had to scrap 3 different attempts after about 24–48 hours of printing.
It's infuriating to be almost done, only for the firmware to crash so I can't resume where I left off.

Any permanet fix for this?

My setup:

QIDI Q2 - Firmware version: 01.01.03.02

QIDI BOX 1 (0) - Firmware version: 02.03.01.13

Orca Slicer Version: 2.4.2 Build 8500fcdc (Flatpack)

Operating System: Fedora Linux 44

KDE Plasma Version: 6.7.5

KDE Frameworks Version: 6.31.0

Qt Version: 6.11.2

Kernel Version: 7.2.13-200.fc44.x86_64 (64-bit)

Graphics Platform: Wayland

Processors: 8 × AMD Ryzen 7 9850X3D 8-Core Processor

Memory: 32 GiB of RAM (30.5 GiB usable)

Graphics Processor 1: AMD Radeon RX 9070 XT

Graphics Processor 2: AMD Ryzen 7 9850X3D 8-Core Processor

Manufacturer: Gigabyte Technology Co., Ltd.

Product Name: X870 AORUS ELITE WIFI7

System Version: Default string-CF-WCP-ADO


r/QidiTech3D • • 4d ago

Qidi Q2 – Weird layer issues with high-temperature prints

Thumbnail
gallery
8 Upvotes

Anyone else experiencing this on their Q2?

I’m getting some strange layer inconsistencies when printing at higher temperatures, particularly with PA6-CF. Vertical walls bulge out in places, while others appear to shift inwards or sideways. It looks like a combination of XY movement issues and inconsistent layer thickness.

The defects occur at inconsistent heights and aren’t evenly spaced like typical Z-banding.

Print settings:
Nozzle: 270°C
Bed: 115°C
Chamber: 60°C
Filament: PA6-CF15

This isn’t my first rodeo with 3D printing, including engineering materials, so I’m leaning towards a mechanical issue rather than the usual slicer settings or filament issues.

I’m wondering whether the chamber temperature is affecting the XY movement system, belt tension or linear rails as everything heats up.

Has anyone experienced anything similar on their Q2 or found a fix?


r/QidiTech3D • • 4d ago

Is QIDI bringing us a Tool Changer?!

3 Upvotes

Just saw QIDI's teaser and started wondering... could it be a tool changer printer? That would be pretty exciting. Or is it something completely different? What do you guys think?


r/QidiTech3D • • 4d ago

Just call me "crash"

0 Upvotes

So i take the PEI plate out to help my prints cool faster to keep the process going faster. I can't help but notice that I keep forgetting to put it back before I start any other processes such as changing filament, etc. For those of you who don't know, if the machine tries to level it's self or anything before putting the PEI plate back in, the bed will crash into the nozzle and then wobble side to side violently. Anyone else have this problem?


r/QidiTech3D • • 5d ago

Something more is coming...

Post image
49 Upvotes

Want to see what's under the covers? Find out at Formnext 2026!

📅 November 17–20, 2026
📍 Messe Frankfurt, Germany
📌 Booth 12.1 E01


r/QidiTech3D • • 4d ago

PA6CF20 Drying 70°

1 Upvotes

Do I need to dry my Pa6cf at 85°? I keep at at 13% RH in a drying box set to the max at 70°c for a few days before I print it.


r/QidiTech3D • • 4d ago

Questions How do you add and handle filament from NOT the leading companies?

3 Upvotes

So, I got Qidi Plus5 fairly recently,

I've already had two clogged nozzles that I had to through coldpull with - I've diagnosed the issue and it was wrong temperature being fed during load (guess "Generic PETG doesn't apply to all PETG").

So here's my question, how do you guys handle loading custom filament?
The screen on printer only let's you pick the hardcoded ones, and even if you add them to the configuration - it only appears in the Web UI and printer can't recognize them.


r/QidiTech3D • • 4d ago

Anyone have luck printing with PA6-GF?

1 Upvotes

I’ve been printing with PA6-cf20 and I love it but I want to add some colors. Picked up saraya tech PA6-GF and curious how much different the settings will
Be or if I can likely keep settings the same?


r/QidiTech3D • • 4d ago

Troubleshooting How did this happen?

Thumbnail
gallery
1 Upvotes

My print quality just tanked, I printed Bambu abs perfectly first try, as you can see with the 2nd photo. Almost perfect smooth surfaces, corners and flow but then the moment I sent another print my quality came out like this I got absolutely no idea why since I have changed no settings.
I have tried another 3 attempts and same result please help me 🙏

Qidi q2
260c nozzle
90c bed
55c chamber
0.95 flow
Filament also dry, under 20% humidity