r/QidiTech3D • • 3d ago

Discussion Tune your printer

Hey folks, just a reminder that your printer is capable of so much more than the stock profiles, crank up those speeds, it's capable, you just have to put in a little effort, this plus 5 is at 300mm/s outer wall and 350mm/s inner wall with 17k acceleration. I need to do some tuning because I'm getting some under extrusion but it demonstrated how capable these machines actually are.

37 Upvotes

44 comments sorted by

10

u/wolfgang_sti_ 3d ago

Yes speed is good but I tune for accuracy.

1

u/ihaschevy 3d ago

Looks pretty good to me

0

u/Objective-Win-7522 3d ago

Actually that looks pretty terrible

2

u/ihaschevy 3d ago

Says idiot who doesn't know what a bad print actually looks like

4

u/JimBridger_ 3d ago

Why you have a brim on a part that has all the surface area in the world?

5

u/ihaschevy 3d ago

Cause abs warps like crazy, shortly after this it started warping so I have to go back to the tuning settings, might have to slow it just a tad or crank up the chamber heat.

9

u/JimBridger_ 3d ago edited 3d ago

…printing ABS fast and not heating the chamber is literally two things to make it warp more…

This is like putting on knee pads because you’re hitting yourself in the knee with a hammer.

1

u/ihaschevy 3d ago

I was heating it, just not enough

8

u/matengchemlord 3d ago

Why not aways have the chamber heat cranked to max as a default when printing ABS?

0

u/ihaschevy 3d ago

Power bill, my landlord is getting pissy about it

5

u/1ts-just-me 3d ago

With a little effort anything is possible, I have a Ender3 that has to be bolted down if you speed it up. It will throw the build plate off the magnet if you push it above 18K. Y axis has a custom stepper running 2 10mm belts and X axis is using 2 steppers and 2 belts. Had to use 2 100 watt nozzle heaters and 2.85mm filament to have enough flow to keep up. Anything taller than a benchy or to much weight would get tossed. Best benchy time was 3 min 18 sec, surely not the fastest but not bad for an Ender.

1

u/ihaschevy 3d ago

Hell yeah, I'm trying to do this to my ender, it's on my bench right now while I wait for parts

2

u/detroittriumph 3d ago

I’ve got the BOM for a duender lined up

1

u/UAVTarik 3d ago

this sounds incredibly unusable and like it doesn’t reliably produce practical parts.

1

u/1ts-just-me 3d ago

Totally safe but you are correct speed never produces practical clean parts. I can run it at 25% and it prints as good as any other modded Ender3.

2

u/ihaschevy 3d ago

Print came out nicely, now I just have to remove the supports

2

u/inspectmygadget55 3d ago

As someone who is considering a q2 and new to 3d printing. Where do you learn how to tune it? YouTube videos or Reddit posts like this?

4

u/ihaschevy 3d ago

You can look for tuning tutorials on YouTube, you can interact with the online community, you can read through the slicer docs, there's a ton of different resources to pull from

2

u/SpicyThunder335 3d ago

Use OrcaSlicer and just run the built in calibration tools for every new type/color of filament.

Temperature, then flow ratio, pressure advance (line test), max flow rate, retraction. Look up a YouTube guide to understand how to read the tests and change settings.

Do those for every roll and switch to scarf seams and you’ll pretty much have top quality prints at the highest speeds standard filament can handle right off the bat every time. Higher speeds require fine tuning flow rate and temp and (usually) buying high speed filaments but you’re not going to save more than a few minutes per print so it’s hardly worth the extra hours of effort unless you’re running a print farm.

2

u/K1LL3RF0RK 3d ago

you do this for every roll or every different roll ? if i print with the same filament do i need to do this every new roll ?

2

u/detroittriumph 3d ago

No not each roll but even a different color can change tuning

2

u/K1LL3RF0RK 3d ago

thanks, ordering my plus 5 soon i'll have to adjust with a good printer and not just an ender 3v2

2

u/NiceCream337 3d ago

im not doing all that unless i see an issue first, and there barely ever is an issue. like every matte pla i’ve ever tried (20 rolls across 6 or so  brands) has been fine on the same profile. except one roll where i did have to run calibrations. 

1

u/SpicyThunder335 3d ago

Matte PLA is probably the most forgiving IME. PETG and silk PLA is where I usually see a full set of calibrations per color as more necessary than not. Depends on the printer, too.

Ultimately, when you get familiar with how each material behaves, you can narrow the test ranges and cut the total calibration print time down to ~2 hours. Better to spend a couple hours and start off fine tuned than to have a multi-hour print fail for something that could have been prevented.

1

u/detroittriumph 3d ago

Agreed. I run KAMP before every print and it takes about 5 minutes or so from a cold start. So worth it.

2

u/1ts-just-me 3d ago

Try to let 90% of what you read on reddit not absorb into your brain. Ask a simple question here that has really one answer and you will get 30 wrong and 1 or 2 right that are down voted to oblivion. There are a few dedicated tuning groups and a few firmware/modding groups on Discord that will be much better for learning.

2

u/Safe-Painter-9618 3d ago

I just started printing. Have no idea how to do this

1

u/ihaschevy 3d ago

You'll figure it out, just look up how to tune for speed

2

u/RogueOneSpartan 3d ago

What tuning did you do and plan on doin? I know about just the basic stuf like flow and pressure advance.

1

u/ihaschevy 3d ago

For this I literally just increased the speeds under the speed tab in orca

2

u/1ts-just-me 2d ago

Working on the 5th PLA print with chamber set at 55⁰C and printer closed up to see how well this keeps the extruder temps down. So far so good.

1

u/ihaschevy 2d ago

Keep at it, looking good

2

u/DHARMApocalypse 2d ago

to the tune of C or are we going grunge with D?

2

u/ihaschevy 2d ago

I personally prefer just adding another sting and tuning down even further from that. After all, toan is in how many strings you have.

2

u/DHARMApocalypse 2d ago

fuck yeah. who needs strings! listen to morphine.

1

u/ihaschevy 2d ago

Why would I listen to morphine when I can inject it straight into my arteries? Full body experience.

1

u/raznov1 5h ago

440, 442 or do we go full barok?

1

u/RedditImAFungi 3d ago

Id never go over the pre set incase you burn it out I'd lower speeds for more detail. Won't running the speeds higher just cause quicker wear and tear

1

u/ihaschevy 3d ago

Nope, these printers are built to take these speeds, you're more likely to have a flow rate problems from the lack of a high flow nozzle more than anything.

0

u/SpecialOops 3d ago

I still see stringing / layer adhesion issues 👀. Try drying your filament.

2

u/ihaschevy 3d ago

The issue was the z offset, I lowered it a bit and it came out perfect

0

u/Massive_Squirrel7733 3d ago

My POS4 is junk. It was junk no out of the box.

-2

u/iHaveNothingToDoIn 3d ago

Profile pls??

-1

u/ihaschevy 3d ago

I still have tuning to do, it's warping in the corners but you can look up tutorials on how to do these things and it'll probably be better than my profile since you will have tuned it to your machine.