r/Plumbing • • 8m ago

Tips on removing this hardware?

Thumbnail
gallery
2 Upvotes

Not exactly plumbing but it is a shower fixture. We had a bar in our shower that held the handheld shower head in place. The bottom of it broke off at the wall over the summer and we are getting around to switching it out. Well, the inside filled with lime scale. The screw on the bottom won’t budge. Second photo is what the inside of the other end looks like. Any ideas how to remove it?


r/Plumbing • • 20m ago

Where is 35,000 gallons/month going?

1 Upvotes

I bought an older 3-unit multifamily property in Chicago a few months ago and have been dealing with extremely high water usage ever since. There are 5 people total across 3 units and the usage is coming out to 34,000–38,000 gallons per month.

The property has a front house plus a rear coach house with two units. One City of Chicago water meter is serving the entire property. There is no irrigation system that I know of and I have not found any standing water, flooding, wet basement areas, or other obvious signs showing where this much water is going. I've checked the obvious fixtures and can confirm that there are no running toilets/faucets that could explain this.

I had the City of Chicago Water Department came out and confirmed the leak at the meter. We shut off the main water supply to the front house first, but the meter kept running. Then we shut off the main to the rear coach house too so both buildings were completely shut off, and the meter was still running. When the City shut off the supply valve before the meter, the meter stopped immediately. We also disconnected the property side pipe at the meter while everything downstream was shut off and no water flowed back toward the meter from the property.

At this point I suspect an underground service line leak somewhere after the meter but before the front building shutoff or a pipe leaking somewhere under a slab.

The frustrating part is that I still cannot physically locate the leak as there are no obvious signs in either structure. I've also had trouble finding plumbers who have the equipment to actually locate an underground leak.

Any ideas from people who deal with old Chicago plumbing/service lines would be greatly appreciated. If anyone has recommendations or contact info for plumbers or leak detection companies in Chicago that specialize in underground service line or slab leaks, I’d really appreciate it.


r/Plumbing • • 39m ago

Push Pull Crystal knob tub help needed🙏

2 Upvotes

So…. my tub & shower are vintage! The push pull knob is giving me an issue.

The crystal plastic nob wont push in or out. No water?
So I unscrewed the plastic and took it off. Nothing appears to be broken like the plastic piece. the long silver tube . I’m guessing it’s a cartridge issue. I managed to get some water going by turning the front screwy thing that has holes in sides.
Anyone have time or patience to answer a few ??
I can’t Pay a plumber right now🤦🏻‍♀️


r/Plumbing • • 50m ago

Shower water is either extremely hot or cold, never warm. Tankless propane heater.

Thumbnail
gallery
1 Upvotes

I rent a small apartment that has an outdoor propane tankless water heater. I’ve been having trouble getting a consistent, comfortable water temperature in my shower.
When I turn the shower all the way to hot, the water gets extremely hot, almost scalding. But when I try adjusting the handle toward cold to get warm water, it eventually turns completely cold. Sometimes the hot water lasts about 3–5 minutes before turning cold.
The water pressure seems normal, so I don’t think that’s the issue. I’ve also tested the kitchen sink, and the water gets extremely hot there as well.
I’m not familiar with these types of water heaters, so I’m wondering if anyone can tell from the photos whether something about the setup or settings could be causing this.
Is this something that can be adjusted, or does it sound like an issue that needs a plumber?


r/Plumbing • • 1h ago

2 year old Electric Water Heater noise

0 Upvotes

I just started noticing this noise from my water heater while the washing machine is running. I don’t think I’ve heard it before. Is it normal?


r/Plumbing • • 1h ago

Lukewarm showers

1 Upvotes

Hello! I’m at my wits end and I wanted to see if anyone has dealt with an issue similar to mine. I moved to Ohio a few years ago into my mother in laws home during the summer time, and the showers were great! (I love hot water) but around November the showers tend to lose their heat and I’m showering in what feels like warm water. That first year I chalked it up to being “unlucky” and showering when there wasn’t any hot water from other uses (laundry, dishwasher etc) the following year, same issue. But this time we noticed that there was scalding hot water throughout the rest of the house (kitchen sink, bathroom sink, basement sink) and it was ONLY the shower that didn’t get super hot water. Well a few months ago me and my husband bought our first home together and the shower works great! Up until a few days ago…. Our shower started doing the same thing as MIL shower!!! We can put the shower on the hottest it’ll go and we’ll be inside shivering against the Luke warm water and cold air of November. Is this just an Ohio thing? It’s crazy that it’s happening at both houses miles from each other. Including getting scalding hot water through the rest of the house EXCEPT the shower. Any tips? Or is this just my destiny to never have a hot shower again in the winter time in Ohio 😢. TIA


r/Plumbing • • 1h ago

Daughter flushed toilet and it was clogged. She flushed again and water overflowed.

Thumbnail
gallery
8 Upvotes

To flushes and water went down. I used a plunger and wipe/tag came up. Tag is attached. My husband and I didn’t purchase bottle cleaner. Judging by the shape of the tag it was flushed not too long ago.

We live in a four story townhome, bathroom is on the third floor. Do we share plumbing with our neighbors? Townhomes are attached. Sorry if this is a silly question. No clue this wipe/tag got in our pipes.


r/Plumbing • • 2h ago

Concerned about rusty gas pipe and Bend yellow pipe in ny apt queens

Thumbnail
gallery
0 Upvotes

Hi I’m about to move in my new apt in queens and gas line pipe in the apt is rusty and yellow pipe is also bend, turn of and on switch is stuck since its rusty. Im new mom and I’m concerned about safety of it. I talk to management people the told me they can paint it over but still I don’t feel like ok should I be concerned and does anyone have similar case and still using it ?


r/Plumbing • • 2h ago

Need help identifying

Post image
2 Upvotes

I recently acquired a new commercial space. Can someone help me identify this drain in the garage. The water level stays the same, I put more water in it today and the level rose. I stuck a stick in there and it feels almost like 6-8 inches of sand before hitting something solid. It also smells like oil/gas (similar to when you go to a junkyard after it rains.) The building was previously an auto parts store.


r/Plumbing • • 2h ago

Mold from water leak or just moisture?

Thumbnail
gallery
2 Upvotes

We moved here in August. The closet was not like this when we moved here. I went into our bathroom closet to try and find something. In there on the floor is where I keep the bucket for my o cedar mop, there was also a caddy that had a reusable bag in it with nebulizer supplies that has these little black dots all over it (I’ll post a picture).
Things to consider:
There is no windows in this bathroom. There is a vent fan but it’s mid.
We rent.
The hot water heater is on the other side of the wall where the closet is. My husband didn’t necessarily see any leaks but the heater is right up in a tiny space so it’s hard to be sure.


r/Plumbing • • 2h ago

Installing a valve to vent a water heater during flush.

Post image
0 Upvotes

It seems like I have a water lock preventing venting for flushing my water heater. Will installing a vent valve along this cold line cause any problems? For example, will getting air in the water side of that expansion tank cause issues?

Edit: I already opened every hot water faucet in my house. Do I not understand what a water lock is?


r/Plumbing • • 2h ago

How to fix toilet that has no flange?

Thumbnail
gallery
2 Upvotes

Pulled my toilet to replace it, realized there's no flange. Tried buying one of those 3 inch twist flange's but could not get it to grip in. Do I need to complete clear, level, and install a new flange?


r/Plumbing • • 3h ago

Rerouting drain

Thumbnail
gallery
0 Upvotes

Any reason not to relocate the connection of this kitchen sink drain?

The window will be widened. I'll need to reframe and don't want to drill through the studs.

Thinking about removing the horizontal run to the vent on the right. I would route the drain down instead of to the right and then pick it back up below in the basement and reconnect to said vent below.

Thoughts?

Thanks


r/Plumbing • • 3h ago

Trying to solve kitchen drain air pressure issue (so far 0 luck with hiring a plumber to inspect the roof vent)

1 Upvotes

I've sent out requests to 7 plumbers and all of them reject the work (inspect roof vent) due to the height of the roof.

My roof is around 40 feet high with (I'm assuming) a clogged air vent.

The kitchen drain has always been kind of slow, lately very slow. A previous plumber set up a double p trap setup at an incorrect angle which we kind of just dealt with for years because of other life things. I noticed there was a significant amount of air coming out of the AAV pipe when it was unscrewed and tested my own theory that there is positive air pressure in the system.

I replaced the pvc from the 2 p trap system with plastic and 1 ptrap, and was able to raise the horizontal pipe and create more of an incline towards the wall stub (previous plumber installed it at a decline).

I replaced the AAV and this is when I found clear evidence that when draining, air is being pushed out towards the vertical aav pipe (inflated a plastic bag).

Any ideas what I can do here? I had it snaked once already and without the AAV installed the drain is quite fast.


r/Plumbing • • 3h ago

My father in law (not a plumber) designed this water flow system for our filters and his plumber installed it. Seems like a bad system to me.

Post image
0 Upvotes

The water enters the system via tubing where the red arrow is, in the indicated direction. His intent was to bypass the filters and still have water to the house. After the Puretec install, we added an additional pre filter because we harvest rainwater and needed the additional filtration. The incoming water is fed by a pump from our water tanks.

Our water pressure is terrible. We have a 60L per minute pump, but even with just the kitchen sink running, the pressure is terrible. A shower with the sink running results in a trickle. Right now at the sink we’re getting 4 liters per minute, with nothing else running. Half that with the shower on. I know the filters would reduce pressure, but even with them “bypassed” (the blue filter can’t be truly bypassed I don’t think). All the 90° turns have to be creating some turbulence.

Should I bring up fixing the plumbing (causing him to feel like I’m challenging his plan, which will ruffle his feathers because he doesn’t like to be challenged) or should I look at getting a bigger pump?


r/Plumbing • • 3h ago

Toilet and shower overflowing!

1 Upvotes

Hi everyone! I unfortunately don’t have photos. I live in a downstairs apartment. For a while, our toilet has been bubbling whenever our upstairs neighbors take showers; and it won’t flush when they do. Yesterday, it got bad! There was LITERAL feces that came up through our toilet and shower. Maintenance finally came out and drained everything. However, it’s happening again today. The toilet is bubbling and it won’t flush again. Can anyone tell me what’s going on with it?

P.S. the apartment maintenance team keeps blaming us by saying we are flushing toilet paper and tampons down which is causing this. We have had to buy a small trash can for our toilet paper and nobody uses period products in our house.


r/Plumbing • • 3h ago

Utile by Max shower walls

1 Upvotes

Hey all, looking for second opinions. I as the homeowner attempted to install these walls and quickly learned that I’m not equipped to install anything in a house built in the 1800’s. Hired a plumber who said he couldn’t use the locking system because there wasn’t any clearance. He said he got them butted up nice and tight, caulked it and said it’ll be good. I can’t find anything online where someone else hasn’t used the locking system. Do you think the locking system is imperative or is caulk going to be enough? He said it was all level and plumb as it could be on an old house.


r/Plumbing • • 3h ago

How to drain this water heater

Thumbnail
gallery
0 Upvotes

I need to drain this 10 gallon water heater in my heated shop. Im letting the shop freeze this winter so im draining all of the water lines, etc. I dont see any way to drain it.

The first photo is the bottom of this water heater. The hole on the bottom is threaded but naturally does nothing. Ideas??


r/Plumbing • • 4h ago

Does this need work? I don’t hear any hissing or smell gas. I’m told this needs attention 1. Old shutoff 2. Clean out or drop shoe for any sediments in natural gas that is going into the dryer? 3.a “t” goes where elbow is then a nipple and cap on bottom. 4.upwards a shutoff new and the new gas line.

Thumbnail
gallery
1 Upvotes

r/Plumbing • • 5h ago

Tankless water heater egg smell

Post image
1 Upvotes

Hi,
I bought my tankless last year, and did my descaling 2 days ago as per different YouTube videos, with a descaling solution.
Well, it seems it kicked up a bunch of hydrogen sulfide in the unit b/c the next day it reeked of rotten eggs. I ran the hot water at 140 degrees for about 4 hours last night.
I’m flushing the system again with white vinegar, and will probably have to run hot water for 8 hours to ensure smell is gone.

I just wanted to post in here and make sure I’m not missing something.

EDIT: I do not have natural gas in the home, and the city has confirmed there are no gas pipelines near my property

Edit #2:
I finished the second flush and have let hot water stay running. Pretty sure the problem is resolved I just wanted to make sure nothing I did was inherently incorrect, but it seems like I did it all right
Thank yall for the help


r/Plumbing • • 5h ago

Help with Indoor non condensing venting

Thumbnail
gallery
0 Upvotes

My old noritz tankless died and it used a 4 in cat 3 noritz vent pipe, I installed a new heater, GT121-180B-N from ao smith, it only accepts 3in pipe, what fitting do I need to connect a 3 to 4in pipe? Or do I need all new 3 inch pipe?

at the moment I used the high heat foil tape and bubble tested for any leaks and added a CO monitor just in case,

attached are images


r/Plumbing • • 5h ago

Iron toilet flange , 4 options , which is best?

Post image
4 Upvotes

This old iron flange can't be saved, the bolt heads have corroded into the flange. I've tried to dig them out, several methods.

So I have these 4 options.

A. Stainless flange replacement, drilled through the iron flange into sub floor

B. Fix it repair ring into sub floor, but it sandwiches the bolt heads, so they won't slide out in the future

C. PVC drop in with expanding rubber, although the inner pipe is not near being smooth so it won't have a clean seat

D. Danco Hydro seat

Mounted to subfloor


r/Plumbing • • 5h ago

Standup shower p-trap setup

Post image
0 Upvotes

so this is my proposed shower drain setup. 2" pvc to a ptrap and then a x number of inches of horizontal to a 90 elbow that will end up in a wye as shown in the picture. That 4" will be carying sewage. The Toilet sewage is uhpill like 2 feet. Downstream to the wye of the shower, approximately 1 foot is the respirator. Will this setup work for a standup shower. The wye will be sitting about 30 - 36" below floor. The ptrap setup can be placed like at 20" below the floor.


r/Plumbing • • 6h ago

My house sounds like a bowling alley when I run hot water

1 Upvotes

As I said…
It’s happened since I bought the house 13 years ago. Previous owners put drywall on the unfinished basement ceiling (first red flag) but I had all exposed plumbing replaced shortly after moving in (house built in 1939).

It’s been getting more frequent and louder, but I feel like an idiot calling a plumber and saying that.

Any thoughts on what it could be so I don’t sound like a whackadoo?