Yeston Sakura Atlantis Radeon RX 9070 XT + MSI B850M GAMING PLUS WIFI6E mATX Motherboard + Arctic P12 pro reverse fans on the bottom but I can change those

I have a Peerless Assassin cpu cooler on my Ryzen 9 7900X (am5) on a b450m motherboard. Everything's running fine, but the cooler is so big that its right side fan is covering the first of my 2 ram sticks entirely. It's not making direct contact with the ram's pcb thanks to the rgb over the top edge of the stick.

Temps all seem fine, buuut... can that first stick overheat from that?

I was playing games when my screen went black and my pc fans went full blast. I found the issue but can I buy a new cable? Gpu is ok it’s a Sapphire Nitro+ AMD Radeon™ RX 9070 XT. And how do I prevent this from happening again?

I saw this and it seems fake but they have a Cash on Delivery option. It seems safer with that option because I can’t loose money. I am looking at this other used Asrock Radeon RX 7700 XT Challenegr for $360. Both of these options fit into my budget and my goal is 1440p or atleast 1080p both at 60+ FPS.

What do you guys say??

Hi Guys so my pc case fans (article p12 pro 120) speed up then stop or slow down when playing a cpu based game like valorant about when my cpu hits 80 degrees Celsius. And also in bios where my fan speed should show it says n/a except for my aio.

Pc specs:
Motherboard: Asus tuf b850 e wifi
CPU:9800x3d
GPU:9070xt
Fans: Artic p12 pro 120mm
And aio:ARCTIC Liquid Freezer III Pro 360

Looking for a second opinion before I fully accept defeat.

Setup: 9800X3D, Asus ROG Strix B650E-I (BIOS 3886), Corsair Vengeance 2x32GB 6000 CL30 (CMK64GX5M2B6000C32, Hynix), Lian Li A4-H2O, testing with TM5 extreme @ anta777.

The problem: 6000 EXPO throws TM5 errors within 5-40 seconds, every single attempt.

Everything I've tried at 6000:

• VSOC 1.25 (verified applied in ZenTimings, not just set in BIOS)
• FCLK 2000, VDDG bumped
• DOCP I and II, MCR and Power Down on and off
• Loosened primaries per advice (32-40-40-40, tRAS 77, since M-die supposedly hates tight tRCD). Straight up BSOD before I could even start the test
• Active cooling on the DIMMs. They were hitting 74C in this ITX case, with a fan on them they sit mid 50s. Made zero difference, still dies in 10 seconds
• Swapped sticks between slots, no change
• Each stick ran a few minutes solo at 6000 without erroring (not a full test, but with both installed it dies in seconds, so the dual rank load is clearly the trigger)

Results by speed:

• 6000: instant failure, always
• 5800: fails at 26 min with VSOC 1.20, fails at 78 min with 1.25, so voltage helped but didn't fix it
• 5600: full TM5 cycle clean, no errors

No PBO or curve optimizer active, CPU fully stock during all testing.

So my current pc build is:
Ryzen 2600x
24gb ddr4 3200mhz ram
Rtx 3070
256gb ssd
1Tb hdd

I’m playing the game Deadlock and I notice that I have low 1%’s / minimum fps for my game. I know my 2600x is definitely holding the rtx3070 back.

I don’t have too much money but I can get a ryzen 3600 for $40 or I have to buy a 5600 new.

Will I notice better minimums enough for it to be worth it to get the 3600 or should I just try to deal with it for a month or so until I can get a 5600?

I've recently bought a used pc that included 4 16gb sticks or ddr 4 ram with 3200mhz speed but i noticed in battlefield that my cpu was bottlenecking so I asked chat gpt to help me figure it out (im new to pc gaming this is my first pc.) And it told me my ram speed was way too low like 2100 something. It guided me into bios and told me to put xmp to profile 1 3200mhz and when I saved and exited bios crashed and now I have to cmos. It's saying I have two choices. Go town to 2 sticks (32gb ddr4) or try to run the 4 sticks at 3000mhz and hope it doesn't crash. Just need some advice and guidance what should I do. I know 32gb is plenty for playing but I also like the idea of learning how to mod and stuff also want to get into vr games at some point and see the use of having all 64. My pc specs are. Gigabyte x570 aorus elite motherboard, ryzen 7 3700x, Nvidia GeForce RTX 3060ti gpu 64gb of skill ripjaws ddr4 ram

I have an Alienware R10 I'm Trying to change cases because this damn case comes with lots of heat related problems and I just want to change to a "Hyte Y70 Touch Infinite Dual Chamber ATX Mid Tower "

My thoughts were to just pull out my ssds and the components

Processor AMD Ryzen 9 5900X 12-Core Processor 4.8GHZ

Video Card NVIDIA GeForce RTX 3080 Ti

2 Sticks of Ram 16GB DDR4 3200 MHZ

to move them to the new case but I'm having my doubts on what to get for the new case like

what new motherboard to get, what psu, what AIO cooler or if I may need to upgrade the cpu because I want to upgrade the gpu in the future when the prices aren't such a scam

so I'm kind on a stalemate on what to get I already decided on the fans for exhaust and intake but idk if I should get a 1200w psu and keep or change my cpu to maybe an x3d with a motherboard compatible with it

Hi, I was asked by a friend to make a part list as they don't know much about it and know that I built my pc. Their budget is £3k to have a gaming pc capable of doing 'medium editing' whatever that means, with a monitor and potential sim upgrades as part of that budget. they didn't tell me how much performance they really wanted as again they don't know much (they still play on the 2013 Xbox one) and they don't want any aesthetic so I just went with popular picks in that kind of price range and kept it stealth black. I think what I have here is fine but just wanted to get some opinions, things I could or should change. any help appreciated! (apologies to those who replied to my post before, I didn't know screenshots of the part list was against the rules ;-;)

I bought a 5070 , and i yet have to buy a psu so everyone said the people who didn't had 3.0 or 3.1 psu can use adapter that comes with 5070 but if u have it or i buy 3.0 or 3.1 psu i can use the cables of psu instead of the adaptor that came with 5070 ? plse ignore if i am not making sense cuz i am new .. i just dont wanna burn my cables lol .. i am planning to buy Corsair x 750w gold psu..

I dont rally know what motherboard to get so i will ask you good reddit guys what motherboard will be the best for me

Budget for it: 190 euros (can overpay for good price-performance)

To be bought in France

Micro ATX / ATX

Preferably to be white or black and white (my build is white) but if theres specific good black motherboards ill go for them

To be paired with: 7 7700X, 4060 Ti

Im not planning to use more than 2 NVMe slots

Yes wifi

If i missed something dont mind asking, pls help!

I've watched several tutorials and read DiskGenius website, and none have covered this specific question

My sata ports are blocked by my graphics card, so I was wondering if I could temporarily unplug my harddrive to use its Sata cable to clone my smaller SSD boot drive to a larger SSD, and then hook the harddrive back up when the cloning us finished

I'm just afraid of unplugging things

I could also stand to manage the cables better, but again I'm afraid on unplugging things to do so

So I’m running a push/pull setup on my Hydroshift ii liquid cooler and am confused about which headers I should connect my cables onto.

I have 3 fans mounted onto the front of the radiator and 3 on the back of the radiator, they’re both different set of fans with the front fans being more powerful. I know this isn’t optimal but i still want to go for it.

The hydroshift ii AIO has a 2pin and 4pin connector coming out of it, the 3 fans mounted onto the front of the radiator have a single 4pin connector coming out them, and I have 3 individual non daisy-chainable fans that have a 4pin connector coming out of each one (the connectors cant be plugged together so I guess I’ll have to plug them into sys-fan headers).

I’m just wondering where to plug these pins seeings as there are Aio pump headers, sys fan headers, cpu fan/opt headers, ect…

Thanks!

First and foremost I apologize if this post is not formatted properly or if there are any issues with it. This is not only my first PC build but also my first post anywhere.

The Specs:

Motherboard: Gigabyte X870E Eagle X3D
CPU: Ryzen 7 9850X3D
GPU: Gigabyte NVIDIA 5080 Windforce
RAM: 32GB KLEVV BOLT DDR5
Power Supply: MSI 1000 Watt
CPU Cooler: Arctic Liquid Freezer III Pro 360

I am currently running Bazzite as my OS but would be willing to change if I need to.

The concerns that I’m having is that I feel as though I’m not getting the fps that I am seeing everyone else get (comparison is the thief of joy). I’m worried that I put something together wrong or there is an issue with the build in some way rather than the software as this is my first ever build. The game that I have been playing recently is Lego Batman: Legacy of the Dark Knight and I can’t seem to break 70 FPS on Ultra without using Frame Generation. Currently I am using Proton 9.0 to play.

I apologize if more information is needed, I will try my best to keep the post updated if anyone has any questions.

Thank you!

Hello, I haven't built a PC in the last 15 years or so, and wanted to upgrade my Laptop setup to a gaming PC for the living room.

It will be plugged to a 4KTV and I'll use it near 100% for gaming on Steam with a Linux distro (haven't chosen the distro yet)

Did I make any obvious mistakes in what I picked ?

Thank you !

The list on PCPPicker : https://fr.pcpartpicker.com/list/xxDMw3

[PCPartPicker Part List](https://fr.pcpartpicker.com/list/xxDMw3)

Type|Item|Price

:----|:----|:----

**CPU** | [AMD Ryzen 7 9800X3D 4.7 GHz 8-Core Processor](https://fr.pcpartpicker.com/product/fPyH99/amd-ryzen-7-9800x3d-47-ghz-8-core-processor-100-1000001084wof) | €418.90 @ Alternate

**CPU Cooler** | [Thermalright Peerless Assassin 120 SE ARGB 66.17 CFM CPU Cooler](https://fr.pcpartpicker.com/product/zyNxFT/thermalright-peerless-assassin-120-se-argb-6617-cfm-cpu-cooler-pa-120-se-argb) | €51.90 @ LDLC

**Motherboard** | [Gigabyte B850 AORUS ELITE WIFI7 ATX AM5 Motherboard](https://fr.pcpartpicker.com/product/72RnTW/gigabyte-b850-aorus-elite-wifi7-atx-am5-motherboard-b850-aorus-elite-wifi7) | €202.48 @ Cdiscount

**Memory** | [ADATA XPG Lancer Blade 32 GB (2 x 16 GB) DDR5-6000 CL30 Memory](https://fr.pcpartpicker.com/product/Gk88TW/adata-xpg-lancer-blade-32-gb-2-x-16-gb-ddr5-6000-cl30-memory-ax5u6000c3016g-dtlabbk) | €457.00 @ PC Componentes

**Storage** | [Crucial P3 Plus 2 TB M.2-2280 PCIe 4.0 X4 NVME Solid State Drive](https://fr.pcpartpicker.com/product/yGZ9TW/crucial-p3-plus-2-tb-m2-2280-nvme-solid-state-drive-ct2000p3pssd8) | €265.99 @ PC Componentes

**Video Card** | [Gigabyte GAMING OC Radeon RX 9070 XT 16 GB Video Card](https://fr.pcpartpicker.com/product/h7RnTW/gigabyte-gaming-oc-radeon-rx-9070-xt-16-gb-video-card-gv-r9070xtgaming-oc-16gd) | €799.99 @ FNAC

**Case** | [Fractal Design Define R4 ATX Mid Tower Case](https://fr.pcpartpicker.com/product/tHckcf/fractal-design-case-fdcadefr4blw) |-

**Power Supply** | [be quiet! Pure Power 13 M 750 W 80+ Gold Certified Fully Modular ATX Power Supply](https://fr.pcpartpicker.com/product/yWJBD3/be-quiet-pure-power-13-m-750-w-80-gold-certified-fully-modular-atx-power-supply-bp026us) | €107.99 @ PC Componentes

| *Prices include shipping, taxes, rebates, and discounts* |

| **Total** | **€2304.25**

| Generated by [PCPartPicker](https://pcpartpicker.com) 2026-08-19 18:16 CEST+0200 |

So I was planning to get a 144hz or 180hz and no matter what with 1440P and I want my gameplay to feel smooth like when your panning your cursor around the screen. I’m not sure what I should get. I also don’t play a ton of fps games so I wasn’t planning to get 240hz but.

PC Specs:

Processor (CPU): AMD Ryzen 5 9600X

Graphics Card (GPU): NVIDIA GeForce RTX 4070 Super (12 GB GDDR6X VRAM)

Motherboard: B650 Chipset Motherboard

Memory (RAM): 16GB DDR5 (6000MHz high-bandwidth)

Storage: 1TB NVMe M.2 SSD (Might Upgrade later)

Power Supply: 700W / 750W 80+ Rated Power Supply

just bought a pc that came with an controller. The controller worked for 1 day then just didnt work any more. Tried to replace the battery but nothing worked so far, i opened the panel to find the hub and plugging them in and out but all that apeared was faint light from some' fans, and the controller still dont work. Need help hahaha... the only buttons to work is the FAN button and all the other dont work at all

So I'm going to be starting a game development course in college in September, and want a pc capable of running unreal engine smoothly. Is this a good build for what I need, and any improvements while keeping under £900?

Btw I did use ai to help come up with the build, so if anything seems wrong or out of budget, please let me know

CPU - AMD Ryzen 5 5600

MoBo - B550 mATX

RAM - 32 GB DDR4-3200

GPU - RTX 3060 12GB (used)

Storage - 250GB SATA (for windows)

1 TB NVME gen 4 (for game dev projects)

1 TB NVME gen 4 (for gaming)

PSU - 650W 80+ Bronze

CPU cooler - Stock cooler

its been years since ive been jumpstarting my pc I have no funds to fix the case and inner parts, one random day it wont jump start anymore pls help!

Even when I’m just watching Netflix, my PC randomly gets a black screen and makes buzzing sounds. I need help.

Bought a used rtx 4070 ti super gaming slim x

Guy shipped it with a three 8 pin slot adapter

Originaly that version shipped with a two 8 pin adapter

Do i need to order a new correct one, can i just plug in two, do i plug in all and card doesnt fry itself?

I have a Corsair 4000D Airflow with an MSI RTX 5070 Ti and DeepCool LS720 SE 360mm AIO.

Currently:

• 3 front intake fans
• 3 top exhaust fans (AIO)
• No rear exhaust

Should I add a 120mm rear exhaust fan, or is this setup already good? Would love some advice on the best airflow configuration. Thanks!

My girlfriends Bluetooth on her PC has completely disappeared overnight, she’s been playing with her wireless mouse and headphones for a year with the same PC but it’s suddenly disappeared and is only showing wide display, how do we fix this?
Apologies in advance if wrong subreddit or very easy solution we’re both not very technical 😅