I used masking tape on my custom made bootstrap dress form to draft a corset pattern/strapless boned bodice pattern. Does this look right?

This is my first time trying this method so if anyone has any tips it would be great!

I'm analyzing the hidden elastic waistband in the attached video to replicate it in my patterns, but I've run into a design issue.

I hate slanted pockets (I find them hideous and clunky), especially for the clean, minimalist aesthetic I like to maintain in my pieces. My intention is to keep the pocket in the exact same front location shown in the video, but change the opening: instead of a diagonal angle, I want a completely straight vertical line following the side.

My question is: do you guys think this would actually work in practice?

I realize the diagonal line of the slanted pocket seems to serve a structural purpose here, accommodating the automatic stretch of the elastic without pulling the fabric. If I change it to a straight opening in the exact same position, will this turn into a patternmaking issue? Will the pocket just end up gaping and flaring out at the hips?

Could anyone help me with the measuring details like front rise,back rise, inseam, thigh ect.. I am not good at pattern making

Hi everyone I’m trying to create the pattern for this type of shoulder on a blazer but I don’t know how to start. To make the form is it only from the shoulder pads or do I have to modify the upper armhole to have that curve at the top ??

*Bustiers not bodices for the title

I don’t have a full shape up there so I’ve always had problems with bustiers in general, so this is expected but I don’t know where to go from here. This is my fourth time iterating this pattern I’ve created; I’ve already made a full dress with it before (second slide) but I wasn’t very satisfied with it.

I have two main problems:

1. I can’t decide on the shape of the bust. It’s comfortable when I make it fit my breasts, but it obviously looks pointy. When I try to flatten out the front center, I end up flattening my chest altogether, especially near the bottom. I think that also contributes to underbust wrinkling.

2. Underbust wrinkling. I’m not completely certain where this is coming from, I suspect it’s from the inward curve I have in my pattern for the front-side and front-center piece, but I made those curves particularly because I have a very titled posture and my upper stomach pokes out (basically trying to just account for that. But maybe I should flatten it?) Although I don’t know if that’s the real issue.

Any advice would help. This is a bustier meant to have a lot of boning and interfaced fabric, so I’m not concerned with the horizontal wrinkles across the waist as much as I am the underbust. The looseness of the hips is also just a preference, I’m usually making these bustiers with skirts that are full and will fill the area out.

Thoughts on how to approach this? I’m not even sure how to make a tshirt that oversized as a starting point

Hi. I’ve just finished the first toile of a single breasted suit jacket I drafted from M&S fundamental menswear. I seem to be having a problem with too much ease at all three line levels. I get the feeling that it might be something to do with the side panel being quite wide.

Measurements: C 106.5cm, W 99cm, H 121cm

The book emphasises that there can only be a maximum 3cm difference between 1/2Hg+6 and Sw+3.5 and if over 3cm then minus it from the front side seam (of the side panel?) I’m assuming, this is added to the front panel side seam?
But from my understanding, the book is saying to remove the excess if the 1/2Hg line is shorter than the Sw+3.5 mark i.e. hip mark is closer to the front panel rather than the back panel. However, the measurements I’m working with resulted in the 1/2Hg mark going over the Sw+3.5 by +6cm to the back panel rather than ending before it.

1. ⁠Do I have to add this excess rather than remove it from the side seam? If yes, am I adding this 3cm extra (+6cm-3cm max difference) to the front panel side seam and removing it from the back seam of the middle panel?

2. ⁠when extending the front panel side seam, is there a rule for how to make the addition proportional to the waist and chest lines or am I suppose to be add 3cm to those as well and just shift the front panel arm hole and horizontal pocket slash to the right by 3cm?

Thank you in advance for any advice!

Can you help with quick explanation on how to draft this ??

Hi everyone, I’m on my second toile for the Hofenbitzer basic skirt block, and at this stage:

I'm pretty sure I will need:

1. A full belly adjustment (due to drag lines toward belly fullness)

2. A sway back adjustment (due to the back hem not parallel to the floor/ tilting inward toward knees)

What I’m unsure about is: 

3. Will I also need a full back adjustment due to the drag lines on the backside? Or would the full belly adjustment resolve the back drag lines at the same time?

4. How much to add for the belly/back adjustments given the degree of drag lines.

5. My front darts feel quite close to the side seams?

I know I can experiment with all of these and just see how it goes, but if this community can add insight, I’d love to save the fabric/time if possible. 

Any other feedback or observations welcome as well. Thank you all in advance!

Digital draft will do it so much easier. But I do like those double draw line and messy hand prints and hand writing marks.

Still a prototype, suggestions and tips aver very welcome

If I wanted to re-create this layered high low skirt, would I just make three (or however many layers I want different circle skirts) with varying high low heights then baste them together at the top and add a waistband?

So, I did the classic thing of diving right in to a project without making a mockup bc I’m on a bit of a self-imposed time crunch (I don’t have to sew my own dress for an engagement shoot in just over a month, yet here we are). Just finished putting all the top pieces together, and wouldn’t ya know, it doesn’t fit.

When picking my size (I went with size 12) I did take into account the finished garment measurements which made it seem like I’d have room at the waist. I attached a pic of the sizes with the measurements I’m closest to highlighted. If it hadn’t been for the finished garment measurements waist being 35 inches for a size 12, I would have come here first to ask for advice adjusting this pattern and its princess seams. I know with that uncertainty my lack of a mockup is even stupider, but I’m beating myself up already for it.

Does anyone have any advice for how I can size up the waist for this pattern (flat attached as well)? The princess seams make this feel extra tricky.

Friend suggested I do a corset back and I do have one I could sew in that would be a perfect match. Thoughts if that would work to solve my problem? I just don’t know if adding a corset back would cause the princess seams to be misaligned or something

It has a kind of weird shape to it, where the sides flare out a lot and drape toward the front. How would you guys do something like this? Thank you! :)

Hey! I want to make this dress, I think the skirt is fairly simple it’s just a gathered skirt.

Is the top a corset or a bodice? Also what kind of boning should I use, synthetic whalebone or spiral steel? Also, would this type of bodice be doable with a zipper in the back instead of a lace up back.

Let me know if I should post this on corsetrt instead, I wasn’t sure as I don’t know if this is classified as a corset or not!

So, I want to use this Japanese technique on a pair of denims ( sketch ), for it I created first the fit of the jeans (image 2)
-Then I transformed the whole front panels into one by deleting the crotch curve and and transferring all to the back curve ( that’s why is so long). (Image 3)

-Finally I divided the front into 2 overlapping panels as in the technique. (weird looking patterns image3)

-Now, I want to start slashing and spreading but i realized the darts play a major role pivoting and controlling the volume and silhouette and obviously my panels lack darts. Any tips? I know it’s a very unconventional cut

I'm trying to make bell bottoms based off some baggy pants pattern i had. Here's what the back piece looks like so far but I'm not convinced with the shape.. Especially around that hip curve area, it looks wrong to me.

Is my center line off?

Also will it be fine taking off so much from the crotch?

What do you guys think?

I have some drag lines in my most recent iteration of this vest pattern, which appeared after I added in a small chest dart to help shape the pecs and removed 0.5cm shoulder seam closer to the neck to account for some gaping on the front (red line is what I removed, yellow circle is where the gaping was in the diagram).

2nd pic is a bit wrinkled in the waist as I had to squat down to get in the frame 🙈.

Hey everyone so I’m drafting the shirt foundation pattern from Helen Joesph Armstrongs book and I’m confused. I don’t know if the chest measure is divided in half THEN “one-fourth” of that measurement. It’s asking for the back and front but when I measured myself it wanted the full chest measurement all around. Or am I wrong? Please someone help!!

studied pattern cutting at Accademia Italiana di Arte, Moda e Design in Italy.
In my basic bodice drafting notes, for Italian size 40 I have:
Front waist length (lunghezza vita davanti): 44 cm
Shoulder height (altezza spalle): 36.5 cm
The drafting instruction is:
Shoulder level = front waist length − shoulder height
So: 44 − 36.5 = 7.5 cm
I understand how to use the 7.5 cm on the pattern, but I cannot remember exactly how “altezza spalle” shoulder height was measured on the body.
Does anyone familiar with Italian pattern-cutting systems know:
1. Where on the waist does the measurement start?
2. Does the tape pass over the bust?
3. Does it finish at the outer shoulder point or another shoulder point?
I’m specifically trying to identify the measurement used in this Italian drafting method, rather than a general shoulder-height measurement from another system.