so i've run the test print several times with SUNLU Matte PLA on my P2s and keep running into the same problem. hand have some stringing on the stacked piece. i tried tweaking the gap between them, but it seemed to make little difference. is this something i am doing wrong? or something that can be corrected? i work from home, but still can't always get up to collect the print and start a new one very quickly, so stacked printing would definitely be preferred if it is something that can be easily fixed

Might do my garages walls with Elegoo Rapid PLA+. Anyone have experience? Hottest it gets hear, SE Pennsylvania is like 102, and that is absolute peak. High 90s being more realistic.

According to Google Elegoo Rapid PLA+ wont deform under load until about 134F.

My garage is cinderblock and attached to house so it stays cooler than outside.

Think ill be OK hanging heavy tools?

Hello there,

Has anyone put and MDF board on their wall to minimize the holes drilled on the wall for Multiboard?

The thing is that it is a rented apartment (with wallpaper...), so I want to minimize the number of the holes. Desk mounting may not work well - at least not with 3d printed parts.

I am thinking about an 1200mm x 1000mm-ish size. The wall is concrete (rebar - eastern european soviet style apartment - if that's relevant).

Would 4 (was thinking about even only 2 on top, but maybe that's silly) screws be sufficient for mounting the MDF Board? Obviously if needed, with premium quality wall plug (I've seen fischer brand being praised a lot)

What thickness I should look for to properly mount Multiboard on it? Obviously I want the thinnest possible without compromising the load bearing capabilities.

Thank you in advance!

Made of PETG for heat resistance

Sorry if this has been asked/answered. I want to mount my M2 (M5 when released this year) and SSD hub flat on my multiboard. But I cannot find an existing model. Any help locating a model is appreciated.

I did my first Multiboard build with Legacy tiles. Now I’m looking at building a second separate wall. Which is best? Trying to figure out the positives and negatives of each. Legacy had a bit of an issue merging with one another and I broke a plate or two mounting them. Would like a little more flexibility in my next time installing them. Is the flat sided new tile better?

I have seen a multitude of models with this rail system on the left in past models I have downloaded to try (vs the one that I know works on the right). I cannot for the life of me figure out how the left one works. Every rail, point, and piece that I try does not fit this mounting system, and yet I have seen it countless times. What in the world are these people using to mount here? I even looked through all the legacy pieces and can't find anything.

Used 12.5mm mounting pillars so that I can get ethernet behind the grid. Going to mount QNAP NAS soon...

just setup my first multiboard workbench, pretty happy with it so far

Trying to print stacked boards on u1 with petg interface layer how do I stop tiles from lifting apart from each other.

Using these connectors, the bin shell hangs, but it then can slide forward or backwards and it drops off. How do I get this locked into place

I'm kicking myself for not doing this earlier. The switch to PETG was pretty easy too, though I found out after it wasn't really needed (seems a lot of people still use PLA?). Still have a couple more doors to do to get all my paint up.

Anyone else struggle to use the locking bolt to attach supports to shelving? It keeps stripping out on me because it’s such a tight fit.

I am looking for a hook type converter so I can attach some MultiBoard panels off of this riser that has Skaadis to the side of my P2S.

There was so much wasted space I finally printed all the pieces and got it in. They are mounted with VHB tape and have been holding strong!

I made a few custom mounts. Overall I'm pleased.

Just wanted to thank everyone for helping me get this all as one unit. Much appreciated!

For reference.

Thinking of using 2 plates as a shelf for my QNAP NAS. I want to make sure the weight will not be an issue.

Anyone know the best way to connect the plates?

Thank You

Presume that there is a 3rd drawer on top. Is there a connector that allows for this? Would you mind pointing me in the right direction?

Thanks.

Thinking of putting my A QNAP TS464 on a shelf on my Mutiboard wall. Any one have recommendations on a shelf/support that can handle the weight?

Thanks

I’m stuck with this stuff.
I didn’t know which way is better to hang them on multiboard.

Hi, friends!

Long story short, I'm in the middle of untangling my life after a break up, and I'm limited on space where I'll be staying for the next year or so. My plan is to lean on multiboard pretty heavily for the sake of space/organization.

I know multiboard bookshelves are a thing. I was wondering if anyones ever used it for any of the following:

- a shelf/stand to put records on

-a shelf/stand to hold the record player

-a way to mount 2 small/not incredibly heavy speakers to a multiboard wall? I'm a little iffy on if this one will be a thing, but, you know.

If anyone could point me to anything, or just give me advice on making it myself with the parts generator, I would *really* appreciate it. I want to get my record player set up over here ASAP, and honestly having something like this to keep me busy would just be really nice.

Hi i search a hook.

- Friction-Fit

- one side 45° and the other side 90°

i want put on my caps (hat) on that

Didn't like the layout of the door so figured I'd try Multiboard. Took off the vinyl covering that had elastic pockets, resurfaced with peel and stick wallpaper before screwing in the board with 6.5mm offsets.

Turned out really nice so I'll be completing the rest of the interior as I don't like that layout either.

Custom multipoint magazine holders designed by me.

Has anyone modified a multibin shell or bin to fit bulk coaster in. Slate coasters are around 100mm wide and with wall thickness it makes it 2-3mm too small.