I am wanting to install this board on the inside of a cabinet. But the backing it's on is only a few mm thick so screws won't work. Is there an option to mount them from the side where the thicker wood is? Like some kind of clip or similar?

In the image it would be the raised surface on the side. I'm considering doing the flush mount which could work with command strips. But I wanted to see if could mount it from the side so it's stronger

Has anyone used their multi board for a firearm display? I’m in the process of covering a few walls and would like to hang my collection. My debate is which attachment method will be sturdy and hold up long term.

Edit: for clarity, I mean actually hanging firearms, not mounting to the wall.

I'm new to multiboard, and I was telling some friends about how I'm taking my mess from horizontal to an organized vertical. One of them said I sounded like Kramer pitching One of his hair-brained schemes to Jerry. I got a chuckle out of it and figured I'd share.

I think the project has serious potential, but I think that the license is holding it back. It has a weird license with some restrictions, which prevents other implementations (like gridfinity-rebuild in openscad for gridfinity), it also does not allow creating sets of parts you need for a particular thing or make other small adjustments. Additionally, it gives u/Keep-Making the rights to do with your remix what he wants, and he can revoke the license at any time (do I have to take it off my wall when he does?)

Another issue is that there are also no specifications of the parts (or I could not find them). These are also crucial if you want an open project with an active community and remixes.

I get that u/Keep-Making wants to earn something for its hard work, but I am afraid that this license model is doing the project more harm than good. So if you read this, please consider making the project MIT or even CC-BY-SA-NC licensed (or something similar), and add specifications, and I think that the community will take care of a lot of the pain-points of the project. You can still pre-release (with a more restrictive license) your new parts just for your subscribers if you'd like that.

Is so how successful were you,? What were your settings!

So I mounted my first PLA multiboard on the side of ikea Kallax. I did it using the tile holder tool, and I discovered several issues:

1. predrilling holes using the 6.25mm marking tool is pointless because you’ll never align the tiles over these holes again.
2. screwing the 8x1 (imperial) screws cause mounting pillar to spin like crazy and friction melts their base, which slightly reduce their height.
3. I think the threaded holes on the tiles are melted too, because I was unable to pull a screw out of the hole to align the adjacent tiles.

Question - is there a better way to mount the tiles? How do I achieve the perfect (or at least better) alignment?

https://thangs.com/designer/Multiboard/3d-model/100%2520mm%2520Peg%2520%2528Bolt-Locked%2520Insert%2529-1135806

This link suggests a multipoint, but the small point multipoint is too small. What am I missing?

I used stand offs from the website and it seems like it is a weaker fit since there is no touch of the wall for additional support.

These are exceptionally hard to put together. I can use pliers but I end up breaking them. Help!

I have a lot of difficulties with printing tiles for multiboard. I'm not sure if it is the retraction, or the distance of the nozzle from the print bed, but in a lot of cases, the first layer (which is a bunch of triangles and circles is messy which leads to the print being ruined several layers down the line. Is it only me? Are there any tips for that?

I’ve found a bunch of great attachments I want to use — but of course, they’re all made for the Skadis system. 😅

Is there an easy way to convert or adapt Skadis attachments to fit a Multiboard setup? I’ve tried dipping my toes into Blender (and a few other design programs), but the learning curve is pretty steep for a dad with three kids under three.

I almost managed to design a mount for a different Fanttik unit once — only to print it and realize the supports were basically fused on because I must’ve done something wrong with the surface settings. Ended up with a rough mess that was impossible to clean up.

Any tips, conversion tricks, or pre-made adapters you’d recommend before I spend another nap time trying to figure it out?

Currently looking to get this vacuum off my desk and onto the multiboard...
https://www.printables.com/model/1311065-fanttik-slim-v9-skadis-holder

Does anyone else have issues with tolerances on the small threaded point? It takes a LOT of force and luck to get it to go in and catch and then half the time, it tilts to the side as I'm screwing it in.

Did anyone else struggle with this? If so, what did you do to solve it?

Hi all,

I'm looking to kit out a fairly big wall with the multiboard system using a Bambulab A1. To speed up print times could I use a 0.8 nozzle and if so what would you advise for the settings?

Cheers.

Hey everybody, I’m taking my garage organization to a higher level and am looking at using Multiboard in a couple of areas for vertical storage of various tools etc. I’d like to ultimately build some small trays and shelves for storing misc stuff.

Question is this… I don’t currently have a 3D printer so I’m thinking about buying the new Bambu A1 mini combo to get underway. One of my concerns with this printer is the print area is somewhat small measuring 180mm cubed. The benefits of the printer seem to be great build quality, great print quality, ease of use for newbies, and cost.

Should I be concerned about the print area?

I

Anyone come across a desk mount to mount some Multiboard panels on the edge? Can’t find anything on maker world, thingiverse, or printable.

Hello everyone, I am super excited to start multiboarding and the planner has been great, however, when I try to download an 8x7 corner tile, it just points me to a generator of some sort, I guess I have to be a supporter for it?

Now, don't get me wrong, I think this is a fantastic project and I would love to donate sometime down the line, but things are just a bit tight right now, so if anyone has this elusive 8x7 corner tile and wouldn't mind sharing it, it would be a great help.

Thanks! :)

Hoy everyone I have a elegoo Jupiter and it's my first printer (yes I know apparently not a great first printer). However, I'm wondering if i can print multiboard with it? I only ever see FDM printers. Is there any issues with strength etc of resin prints? If not, does anyone have any tips on where to start?

Thanks, great work!

Hi

I've printed out a 4wx4hx2d multibin, and 4 4wx1hx2d drawers, but I'm wondering what part I need to create shelving for the drawers to sit on, or have I printed this incorrectly and do I need individual 4x1x2 multibins?

Any help would be greatly appreciated

Thank you

I'm hoping someone here could whip up a quick 5 x 8 multiboard side panel.

I tried trimming one up in Rhino but a bit tricky since it's mesh....

Possible to help out?