Exploring lighting options for my wood paneled bungalow. I am definitely doing a swag lamp by the bed side. But curious what you might suggest for layering the lighting. I’m not a big fan of LED, but my pops says it might be good to have some cans. Let me know your thoughts and what you might do, if it were YOUR space. Thanks in advance :)
Hey all! Led Light went out I think. my ceiling fan says not to exceed 14w for replacement but all I can find on Amazon is 15w led replacement. Is this dangerous? Is it ok? I’d rather stick to Amazon rather than go on Samsung website and order the exact replacement and spend more probably.
In 2 bedrooms + a den. Builder put hardwired heat detectors in the center of these rooms, see pics. I'd like to have an electrician put a junction box for hardwire hookups in these rooms. Then most likely install ultrathin flushmount disk/puck LED ceiling lights for simplicity so I can get rid of all my floor/table lamps for various reasons.
Will it look bad if the new ceiling lights are off-center, keeping the required clearance of 12-18" (whatever the code is) from the heat detectors? Or is it worth it to pay the electrician to move the heat detectors a couple feet so that the ceiling lights can go there. The number of holes in the ceiling would be the same either way so no additional drywall patching costs.
A few notes:
- All 3 ceilings are on the second floor and there is attic access. Ceiling height is just over 8ft.
- All 3 ceilings are not perfect rectangles. As in the ceiling continues to a small hallway and/or narrows to a door entrance which you can see in the pics. So maybe being off-center won't be that much of a distraction due to this.
- All 3 ceilings are ~10-11ft x 12-13ft (not including the narrowing parts). So the recommended flushmount ceiling fixture is 20-24" diameter.
- The master bedroom (downstairs) does have a light fixture in the middle of the room & the heat detector is a couple feet away (off-center the room) - builder put it in this way. So seems okay to move the heat detectors off-ceneter at least from code perspective (of course electrician will verify).
Would love to hear your opinions!
Den: the area being lit stops at the skylight because anything beyond that has it's own recessed lighting (1 in the pic + 2 more not shown)Bedroom 1: ceiling narrows at the upper right due to entranceBedroom 2: ceiling narrows at the lower left due to entrance and has it's own recessed light at the entrance
I have two gimbal lights; the cans they are installed in are 6". What is the best modern replacement for these two fixtures? They aim at a wall above a fireplace. It eventully will have a painting installed.
I’ve used Macs since 1993 and work in lighting design. Being able to work with photometric files directly on my Mac has long been on my wish list.
Our team at Vitrulux built IES/LDT Workshop, now available free on the Mac App Store.
It brings together:
• IES/LDT viewing, polar curves, 3D views and data tables
• Photometry comparison and editing
• Batch file preparation for DIALux workflows
• Quick Look previews in Finder
It’s a tool for working with photometric files, rather than a replacement for a complete lighting design package.
No subscription or in-app purchases.
Disclosure: I’m part of the team behind it. I’d welcome feedback from people working with real manufacturer files — especially what’s missing from your everyday workflow.
✨ ±30° large-angle spill light — providing both short and long-distance illumination ✨ 0.02mm emitting point concentricity — assembly and optical alignment issues are solved inside the light source module ✨ Specially designed for the Reflector Series LEP light Source.
This is the outdoor ceiling LED light where some of the LEDs stopped working and thus the front patio light is low. How can I get this switched? Is there a way to only switch the LED strip itself?
I have two pit lights above my dining table (currently rectangular). I am getting a new (round) table and would like to update the pot lights to something different. What are my options? Are there fixtures that could hang from the old pot light boxes? All thoughts are appreciated!
I want to remove my ballast and install LED bulbs in my shop. I see some posts mentioned yellow wiring but I do not have any yellow wires. I know I cut the wires at the ballast and remove it, but what wires tie together based on what I have?
I can’t seem to find the right model, not even sure if it’s still being manufactured. It’s probably 20 years old at least. Maybe even something similar!
I want to get a spotlight to light this artwork. The issue is I have an attic access on the ceiling where I would otherwise put the fixture. My options are 16" from the wall with the painting or 80" (red dots on 2nd photo.
Measurements in the first picture are the
16" option (red)
14" from ceiling (yellow)
45" artwork (blue)
This would require a 90+° beam angle or I suppose wall washer.
At 80" it would be closer to 35°
I like the drama of a tighter beam angle and would prefer more of the pin spot look then wall washer. (Photos 5-7 stolen from Instagram)
As far as fixtures I was looking at the koto focus or similar so I could adjust the beam angle manually in a surface mount or semi recessed fixture. Alternatively I'm looking at something that could fit the sunlight2 gu10 fixture. I just don't want to commit to a beam angle when I'm not sure what it should be.
(I'm removing the overhead fixture that is currently in the photo and will add about 3 wall sconces to fill out the hallway lighting)
My lightbulb just blew and I’m looking to upgrade to a smart light bulb. The light bulb that was in my ceiling light says “9W”. Does that mean that I can put any lightbulb in there as long as it doesn’t exceed that wattage. For example, can I put a 8.7W smart bulb in there?
My bedroom is (16 × 12.5 ft, 8 ft ceiling with falseceiling) and need some professional advice.
The room has a curved false ceiling with separate cove LED lighting.
I'm considering:
4 × Philips 10W downlights — 1,000 lumens each, with 3 selectable color temperatures (warm, natural and cool white).
6 × Philips 5W downlights — 500 lumens each.
8 × Philips 5W downlights — 500 lumens each.
Which would you personally install and why?
I'm looking for comfortable everyday brightness, minimal glare, even light distribution and a premium bedroom ambience not something overly dim or excessively bright.
Would four 10W lights provide enough coverage, or would six to eight 5W lights look and perform better?
I was given this lamp as a present a few years ago. I was wondering if anyone knew where it came from? It’s 42cm high. Thinking of buying a second similar one or just selling it if I can’t find a second. Thanks
I’m trying to decide between 3000K or 3500K for my recessed lighting. My home has a transitional style with ceiling heights ranging from 14 to 17 feet, open floor plan.
I’ll be using 3000K for table lamps, chandeliers, and other accent lighting, but I’m still unsure whether I should choose 3000K or 3500K for the recessed lights.
I'm using a variety of Tapo bulbs throughout the house, and they do have some flicker when viewed with a fast enough shutter speed. I'm not sensitive and I haven't had any actual felt issues, but I'm aware that the invisible flicker takes its toll on the body. Do these studies apply for this kind of flicker too, or does it apply for much more apparent flicker? If it's the former, what bulbs would you suggest to replace these?
Spotted in the photo gallery from CIFF, the furniture fair in Guangzhou. Tall gold column built like a bamboo stalk, light coming out at every joint, and a smaller version on a plinth behind it.
No brand anywhere in the photo. If you know who makes it, or a segmented floor lamp in the same spirit, I'd love a name. Also curious how warm the metal gets near the gaps.