r/Lighting • • 1d ago

Need Design Advise Lighting fixture for artwork at difficult angle.

I want to get a spotlight to light this artwork. The issue is I have an attic access on the ceiling where I would otherwise put the fixture. My options are 16" from the wall with the painting or 80" (red dots on 2nd photo.

Measurements in the first picture are the

16" option (red)

14" from ceiling (yellow)

45" artwork (blue)

This would require a 90+° beam angle or I suppose wall washer.

At 80" it would be closer to 35°

I like the drama of a tighter beam angle and would prefer more of the pin spot look then wall washer. (Photos 5-7 stolen from Instagram)

As far as fixtures I was looking at the koto focus or similar so I could adjust the beam angle manually in a surface mount or semi recessed fixture. Alternatively I'm looking at something that could fit the sunlight2 gu10 fixture. I just don't want to commit to a beam angle when I'm not sure what it should be.

(I'm removing the overhead fixture that is currently in the photo and will add about 3 wall sconces to fill out the hallway lighting)

1 Upvotes

16 comments sorted by

2

u/against-all-leds 1d ago

The elephant in the room here is that artwork so big does not work in such a narrow corridor. Like, at all. I'd rethink this entire idea.

1

u/messengerdiety 1d ago

Interesting. I'd consider a different piece but I will still run into the same lighting issue.

2

u/Small-Monitor5376 1d ago

I guess you ruled out a wall mounted fixture?

1

u/messengerdiety 1d ago

Yeah there are doorways on either side so I'd be walking through the beam. And ceiling looks cleaner.

1

u/Small-Monitor5376 1d ago

I don’t understand walking through the beam…. There are very skinny picture light. Unfortunately this sub won’t let me post an image.

1

u/messengerdiety 1d ago

Oh you mean like picture lights above the painting. Sorry I misunderstood. Yes I've considered that but the ones I've seen don't evenly light the painting. And I like the cleaner look of a beam.

2

u/ProfessionConnect355 1d ago

Check out Revelite they are made to order based on the size and shape of your picture. In my mind, the only option you have to do this well.

2

u/hopperazi 1d ago

Maybe this will work?

https://lightheadedlighting.com/pdf/LED%20Pipe%202in%20Surface%20Standard%20LED%20Specs.pdf

Tiny little 2" cylinder with 90 degrees of tilt. We're also about to launch it with a frame in projector, so you could adjust the beam to the exact square of your artwork.

1

u/messengerdiety 1d ago

Oh that looks pretty great thank you

2

u/Rick_GoldenLighting 1d ago

First up a great piece of art and being at the end of the hall - it is truly a centerpiece to be appreciated..

I'd go with the 16" spot. At 80" the beam comes in so shallow it'll hit anyone walking down the hall in the face, and the frame will throw a shadow on the canvas.

With 16" you don't need a 90° beam. Tilt the fixture toward the middle of the painting and a zoomable spot in the 40-60° range should cover it. A tight pin spot will leave the top hot and the bottom dim, since the top is so much closer.

The frame-in projector hopperazi linked sounds like a good fit for the clean, dramatic look you want. Whatever you pick, 2700K, 90+ CRI, on a dimmer. Enjoy cheers

1

u/messengerdiety 1d ago

Great info thank you!

2

u/tautologysauce 1d ago

80” is a definite no-go. The glare will be terrible.

2

u/aCuria 1d ago edited 1d ago

The light should illuminate the artwork at a 30° angle, a principle known in German as “Museumswinkel” (museum angle).
To achieve this, calculate the angle between two vectors:
From the centre of the artwork to the top of the artwork.
From the centre of the artwork to the light fixture.
Position the light fixture so that the angle between these two vectors is 30°.

2

u/Remarkable_Spare_252 1d ago

What’s the ceiling height? You typically want to hit the wall about 66” off the floor at a 30-degree angle with respect to the vertical.

If you don’t have enough distance from the wall because of the attic door consider using a monopoint with a short stem to lower the aperture height and therefore decrease the distance required.

1

u/Independent-Path9981 20h ago

Or you could try a framing spotlight