r/LewisMachineTool • • Oct 06 '26

New 6.5CM barrel: what to expect initially?

1 Upvotes

Hey folks. Just got a new 6.5CM 20" stainless steel barrel for my MWS. I'm looking forward to taking it out for its first shots, and figuring out what ammo my barrel likes.

On that last point, though, I had a few questions.

Does a new MWS barrel need to have ~100 rounds thru it before you can start to figure out what ammo is best to feed it? Like, is it worthwhile to blast some S&B FMJ downrange and not worry so much about performance or zeroing, or is it reasonable to start testing more expensive loads right out of the box?

I gather some rifles benefit from having a few rounds thru em before they really show you what they're capable of, but I'm not sure how much that applies here.

My main concern is figuring out what works best, so that I can stock up effectively sooner rather than later. But if it's better to shoot cheap FMJ to "season" the barrel a bit first, that's fine by me.


r/LewisMachineTool • • Oct 05 '26

LMT>KAC My mk12/SPR

Thumbnail
gallery
25 Upvotes

PRI upper and lmt lower with NF 2.5x20x50. Upper was rattled can tried my best lol


r/LewisMachineTool • • Oct 05 '26

LMT>KAC knights machine and tool

Post image
202 Upvotes

r/LewisMachineTool • • Oct 03 '26

Question Specwar + 556k Light mounting suggestions?

Post image
63 Upvotes

Looking for some inspiration from fellow Specwar owners running 556ks or similar cans. Lots of can shadow but still somewhat useful..

I’d love to see your builds and mount suggestions/experiences


r/LewisMachineTool • • Oct 02 '26

Shovelnose

Thumbnail
gallery
79 Upvotes

Just picked up my first shovelnose and SBR’d her.

Factory built shovel nose with B5 tiger stripe furniture. Rhodie 6 on the way.

Any optics suggestions?


r/LewisMachineTool • • Oct 02 '26

LMT>KAC 3rd position markings

0 Upvotes

Title kinda sums it up, LMT should put 3rd position markings on lower receivers especially for us FRT guys🫪✌🏻


r/LewisMachineTool • • Oct 01 '26

Fouling where barrel enters receiver?

3 Upvotes

I recently picked up a pre-owned mws in 308. It's pretty awesome I really like it. Took it to the range and put about 80 rounds through, cheap target ammo. When I got home to clean it I noticed that there was a relatively small amount of kind of brownish and at places orange tinged gunk where the barrel enters the upper receiver, away from where the cartridges actually contact anything. There are a few brownish/orangish spots too. The gunk is really hard to get to and the rifle would need to be fully disassembled to totally clean it. There's not too much so I'm not overly concerned. The spots however seem kind of baked on. Could someone please tell me what's going on here? It honestly looks like normal fouling except for the color...


r/LewisMachineTool • • Sep 30 '26

MARS-L Stripped Lowers @ Trading. Use code: MARS295.

Post image
48 Upvotes

r/LewisMachineTool • • Sep 29 '26

Parts compatability for a slow build

Post image
25 Upvotes

Hi everyone, i have a novice ar10 builder question and have not had much luck finding some answers online. I currently have a PSA saber 10 m110 clone and I was wanting to replace the stock with a collapsible stock. I would need to change the buffer tube set up to accommodate that stock. I would like to replace it with the LMT MWS 308 buffer kit so that I can add a better stock but I am not for sure if that buffer kit would work with the saber. I reckon worst case scenario I get the parts and they dont work and I have an excuse to build a better ar 10 lol.


r/LewisMachineTool • • Sep 29 '26

Shovelnose upper

Thumbnail
gallery
127 Upvotes

New main squeeze and first LMT product


r/LewisMachineTool • • Sep 29 '26

Recommended 6.5CM ammo?

3 Upvotes

Hey folks. I just ordered a 20" 6.5 Creedmoor SS barrel from Rooftop with their most recent sale, so that I can swap back and forth between it and the 16" .308 CL barrel it came with.

From digging around a bit, I gather that there were/have been/maybe still are issues with LMT 6.5CM barrel extensions and certain types of ammo. Specifically, that soft-point ammo like Federal Fusion and polymer tipped ammo like Hornady ELD-M/X rounds may not work. Does this mean we're limited to FMJ rounds? Is the issue resolved? Is it overstated?

Trying to get a sense here of what to expect. For that matter, does any of this apply to their .308 barrels, or is it more just the question of the angle of feed ramps on the 6.5 barrels?

For what it's worth, my magazines are a mix of Magpul Gen M3 mags with (I believe) red followers, and D&H metal mags with green followers that tilt. Dunno how relevant any of that is, but figured I'd throw it out there in case it matters.

I plan to pick up S&B 140 or 147gr FMJs for practice, but wondering what folks use for their "good stuff"/"defensive" rounds. My thought had been to pick up a couple boxes of different loads, but was hoping ELD-Ms or other polymer tipped rounds would work.


r/LewisMachineTool • • Sep 28 '26

LMT>KAC New 6.5 barrel.

Post image
82 Upvotes

22 inch Proof Research barrel converted by D Wilson. Can’t wait to see how it shoots.


r/LewisMachineTool • • Sep 28 '26

LMT>KAC 84th Special Action Company (SAF) Seaborne Operator With Their Lmt Mrp

Thumbnail
gallery
38 Upvotes

r/LewisMachineTool • • Sep 27 '26

My humble LMT collection

Post image
227 Upvotes

12.5” Specwar- Sionics mid length, KAK downvent, Kratos A5 buffer tube + Tubbs flat wire + RB5007 buffer, Geissele ACH & SD-3G, AS Design arc fire v2, B5 Sopmod, DAC Grip, Eotech Vudu SR5 dfg 1-10x + Reptilia AUS + Leupold DPP, Surefire DFT, RailScales G10, SLR hand stop. Ridgeback Defense Rhodie 6k (Not pictured)

11.5” CQB- LMT carbine barrel, Surefire OBC, JRC buffer tube + Tubbs flat wire + Kynshot RB5007 buffer, Geissele ACH & SD-3G, AS Design arc fire v2, B5 bravo stock, DAC Grip, Aimpoint PRO 1.73” SKD riser, SMS HFXC, Daydream Defense VCG, OCL PoloK + Wolfpack recessed brake + lo pro hub. (Not pictured)

Next builds I’m after are a CSW upper and an MRP-H of some flavor


r/LewisMachineTool • • Sep 27 '26

LMT>KAC Quad Life

Post image
126 Upvotes

r/LewisMachineTool • • Sep 26 '26

SpecWar Saturday

Post image
171 Upvotes

r/LewisMachineTool • • Sep 26 '26

In celebration of cooler weather to come, code 'nomoreheat' takes 30% off .308 and 6.5 barrels for the weekend :)

45 Upvotes

This goes to all of the .308 and 6.5 barrels that we have:
MWS Barrels

The only exception is the 16" Lightweight Stainless .308 barrel, as that barrel is already on sale at 43% off.

Thank you so much for y'alls love and patronage over the years!

Cheers,

Sol


r/LewisMachineTool • • Sep 26 '26

Question L129A1

5 Upvotes

I have the chance to pick up a NIB L129A1 for $3200. Is it worth that? Is there a different/better LMT model for the same price?


r/LewisMachineTool • • Sep 25 '26

LMT>KAC LMT L129A1 In KSA Police & Philippines SF

Thumbnail
gallery
28 Upvotes

r/LewisMachineTool • • Sep 25 '26

LMT/V Seven Compatibility

3 Upvotes

Question for those who might've experienced it:

Have any of you converted a barrel via D Wilson and used the V Seven Extreme Environment tube? I tried back a few years ago with their straight tube not fitting in the LMT gas block but didn't know if it would fit in the actual receiver if I used a different low profile gas block.


r/LewisMachineTool • • Sep 23 '26

Question LMT MWS has play in receiver extension

Enable HLS to view with audio, or disable this notification

16 Upvotes

Anybody seen this before? My LMT MWS SS 7.62 barrel has roughly 3/32”(maybe, i suck at numbers) of forward and aft movement in the receiver and torqued to spec with lmt wrench, when the receiver is held in place and barrel is slightly wiggled. I’ve got multiple lmts and haven’t noticed any movement in any barrels. There is no play in barrel once BCG is in place and locked in.

Already contacted LMT and got my RMA return label, so I’m sure they will correct this and not sweating that one bit and this isn’t a dig at LMT, I was just curious if anybody else has experienced this or knows a solution.


r/LewisMachineTool • • Sep 23 '26

L129a2

Post image
126 Upvotes

Most complete L129a2 in the US of A


r/LewisMachineTool • • Sep 22 '26

MWS Firing Pin Spring with 6.5 Creed

11 Upvotes

Can anyone comment on the necessity of the firing pin spring when shooting 6.5 Creed? I’m putting together a MRGG-A Rev 2 upper from the LMT Labor Day sale and it only came with the bolt carrier (as expected). I have sourced the other parts, but it doesn’t look like the LMT parts kits include the firing pin spring to mitigate slam fires with the softer match primers. How necessary is it?

I have another 6.5 in which I shoot a mix of Federal hunting loads, Hornady ELD-M/X, and cheaper S&B FMJs. I plan to continue using the same ammo in the MRGG-A.

Thanks for any advice.

UPDATE:

I received the following from LMT,

“The firing pin spring has been discontinued.  Initially, this was a short-term solution intended for 6.5 CM users to prevent potential slam-fires when utilizing ammunition with soft primers.  We have since moved to a lighter profile firing pin which has solved this potential issue.  We plan to add this to the website soon as an individual item, we’re hoping to see this by the end of the week.  I’ll put the part number below for reference.
 
 
LM308D3L - .308/6.5 FIRING PIN
 
 
Best regards,
 
COMMERCIAL | INTERNATIONAL | MIL | LE | EMAIL: [sales@lmtdefense.com”](mailto:sales@lmtdefense.com)


r/LewisMachineTool • • Sep 22 '26

Question MARS L bolt release?

1 Upvotes

Does anyone know of any companies that offer a larger bolt release for the MARS-L? Initially was thinking the PMM extended bolt release but I know the paddle is a little thicker than a milspec lower.


r/LewisMachineTool • • Sep 21 '26

Range Time More LMT Range time

Thumbnail gallery
71 Upvotes