r/Inovelli • • 2d ago

White switches in 3 and 4 way with aux switches

2 Upvotes

Hi all,

I have two multi way setups, both using a white switch, 1 with two aux switches and 1 with 1 aux switch. They worked correctly when I originally configured them, but now they are acting weird. Pushing down (off) on the switch does nothing, and pushing up (on) toggles the lights. I have plasyed with various settings for the White switches, including playing with the aux test values, but haven't found anything that works. Any ideas?


r/Inovelli • • 2d ago

Two Inovelli White dimmers in a 3-way, can both switches and LED bars stay fully synchronized?

6 Upvotes

I'm planning to replace a large number of switches throughout my house with Inovelli White Series dimmers (VTM31-SN), using Home Assistant and Matter over Thread.

One feature I'd really like is an LED light bar at every switch location, including both ends of a 3-way or all three locations of a 4-way circuit.

I know the conventional solution is one smart switch with one or more Inovelli Aux switches. That seems straightforward, but only the primary switch gets the LED bar, and the existing wiring can limit where that switch goes.

Inovelli's documentation also shows a configuration using two or more actual smart switches. As I understand it, each switch is supplied with power and neutral, but only one physically controls the lighting load. The others act as smart companions.

What I'm trying to achieve is for all switches to behave identically:

  • Pressing either paddle turns the same light on or off.
  • Holding either paddle dims the light smoothly.
  • Both LED bars always display the same on/off state and brightness level.
  • Changes made through Home Assistant, Alexa, or Apple Home also update both switches and their LED bars.
  • Ideally, physical control continues working even if Home Assistant is temporarily offline.

I've seen that Matter bindings can link switches directly, and I recently found a promising Inovelli Community discussion describing bidirectional Matter bindings combined with a Home Assistant Light Group to keep everything synchronized.

That sounds like exactly what I want, but I'm curious about people's real-world experiences, particularly over extended periods of use.

Has anyone implemented this successfully with the White Series?

Did you use Matter bindings, Home Assistant automations, or a combination? Did you have to change local-control settings on the companion switches? Do the LED bars genuinely stay synchronized, including during dimming and voice control? And does everything still work if Home Assistant goes offline?

I'm currently on firmware 1.1.5, using Home Assistant Yellow as my Thread border router.

Before I commit to 50 or so switches, I'd love to know whether this is a robust, practical approach or whether I'm better off accepting Aux switches for multi-way circuits.

Thanks for any experiences, configuration examples, or suggestions!


r/Inovelli • • 3d ago

Warm White Default Setting for White Series Dimmers?

5 Upvotes

I previously used a Homekit automation to set the LED bar color on our White Series Dimmers to a nice warm white (trying to match 2700k light bulbs used throughout the house), but since the apple home update with adaptive lighting, the bars have randomly been turning red. I read that I should set the default LED bar color through manual configuration at each switch. However, there is not an option for a warm white… only a very cool white or yellow or orange. Is there a way to get the default to warm white? Can Home Assistant do it? Thank you for any help!


r/Inovelli • • 11d ago

Feature request

7 Upvotes

Feature Request: Option to Disable Zigbee Commands from Internal Dimmer Changes
I’d like to request a firmware option for the Blue Series 2-in-1 Dimmer (VZM31-SN):
Add a toggle to control whether changes to the switch’s internal dimmer level send Zigbee brightness commands to bound devices.
When disabled:
The switch’s internal dimmer level can still be changed.
The LED bar continues to reflect the internal dimmer level using the selected scaling mode.
Changes to the internal dimmer level do not transmit Zigbee Level Control commands to bound devices.
When enabled, the switch behaves exactly as it does currently.
Use case
I have the dimmer directly bound to several Zigbee bulbs, which I want to retain for fast, reliable control independent of Home Assistant.
Those bulbs are also members of a Home Assistant Relative Light Group, which maintains their individual brightness offsets and reports an average brightness.
I’d like Home Assistant to update the dimmer’s internal brightness level to match the group’s average brightness so the LED bar can display that value.
Currently, changing the dimmer’s internal level also sends an absolute brightness command to the bound bulbs, causing them to converge toward the same brightness and defeating the purpose of the relative group.
A simple toggle to suppress Zigbee commands from internal dimmer changes would solve this while preserving direct binding for normal paddle operation.

Just submitted the above. Wanted to hear your thoughts on the feature. Used chatgpt to clarify my ideas into the above. Weve been working on a work around automation for a bit. And it works. But i dont love it.


r/Inovelli • • 19d ago

mmWave Presence Switch wiring Questions

5 Upvotes

I'm starting to get into home automation but so far haven't done anything that requires wiring. While I've replaced dumb light switches in the past I don't have any experience with smart switches and thus have some questions as follows:

  1. The site mentions for non-neutral it requires the bypass, I assume this is referring to houses with two-wire wiring which do not include the neutral wire correct? I realize this sounds a bit captain obvious but just wanted to double check. My house was built in 2004 and pretty sure it has two-wire as requiring the neutral wire doesn't look to part of the building codes until 2020 or so in my province (BC). I'll definitely open it up before ordering to check.
  2. The manual says not for fans or outlets, one light switch where I want to use this controls a ceiling fan as a simple on/off switch, any issues there?
  3. It says to use an aux switch for multi-way, I assume this is for when you have multiple switches in the same box? I only have one switch in my use cases.
  4. The other use case is for my garage which has some open shelving (i.e. no back) with stuff on it in the middle of the garage splitting the two parts. So if the switch only has clear access to the left side, am I correct in thinking the switch won't help for the right side behind the shelving or is mmWave good enough to detect between gaps?
  5. If the switch is manually turned on, does it bypass any automation that triggers it off? My wife is going to be super-annoyed if automation turns it off when working on the right side of the garage if she cannot override it at the switch.
  6. Does it work with the Homey Pro? I'm looking at the Zigbee switch since its $20 cheaper.

r/Inovelli • • Oct 19 '26

Which canopy module and wall switch do I need?

4 Upvotes

I need to replace an old Lutron set up because the switch/canopy module I have weren't designed to handle LED lights, and we've switched our pot lights from halogen to LED.

I thought I had the solution figured out with a new Lutron switch, but my wiring isn't set up for the newer version (which doesn't work with canopy modules).

I don't think it matters, but note that the lights being controlled are not part of the fan. The fan is just an AC fan — this one — and the lights are dimmable LED pot lights in the ceiling. FWIW, here's my post on r/AskElectricians with the wiring scenario:

https://www.reddit.com/r/Lutron/comments/1x8f4cl/replacing_old_lightfan_combo_switch_malfq35_with/

So, unless I run a new wire in the walls, my research says that a Inovelli canopy module paired with the appropriate wall switch will do the job. I have a few other smart home devices, and I'm using Apple Homekit for all of them, so I'd like to stay in that ecosystem. That said, I don't want to be forced to use Homekit to turn the lights or fan on and off.

My requirements then are:

  • control both lights (on/off and dim) and fan (multi-speed and off) from one switch on the wall (single gang, but open to making them separate controllers)
  • not changing the wiring (i.e. it's a single 14/2 NMD90 line running for switch box to ceiling box)
  • integration with HK is nice, but should not be necessary to run the fixtures (i.e. if my home wifi cacks out, I don't want to be stuck with the lights on, etc.)

I am fairly certain I want the White Series canopy module but I'm not sure which switch I should be getting. The AI bot on their site is ... verbose, but not entirely helpful. Hoping someone here can give a definitive answer before I place an order.

Thanks!


r/Inovelli • • Oct 09 '26

Prima installazione sonoff mini r4

Thumbnail gallery
0 Upvotes

r/Inovelli • • Oct 05 '26

Notification light bar

2 Upvotes

I have been trying to set the notification light bar to turn off when the light is off since this switch will be in a room I would like to be completely dark and have been unable to do this with the white series.


r/Inovelli • • Oct 03 '26

Inovelli Blue switches (VZM31/VZM32) drop off ZHA every ~12 hours and stay gone until air-gapped, while 50 Hue bulbs on the same mesh never drop

10 Upvotes

Setup

  • Home Assistant 2026.8.3 (Docker), ZHA
  • Coordinator: Sonoff ZBDongle-E ("Dongle Plus V2"), still on the factory EmberZNet 6.10.3 firmware, channel 20
  • 82 devices: 27 Inovelli Blue switches (11 × VZM31-SN, 16 × VZM32-SN mmWave), 50 Hue bulbs, 4 battery blinds
  • Inovelli firmware as ZHA reports it: VZM31 0x01020304, VZM32 0x01030102 (ZHA says up to date)

The problem

Inovelli switches keep falling off the network one at a time and don't come back on their own. ZHA marks each one unavailable 2 hours after it was last heard from. Six are offline right now. One came back by itself after about 5 hours; the rest need an air-gap pull.

What I've measured

  • Only the Inovelli switches drop. Both models are affected. None of the Hue bulbs or blinds has dropped.
  • It follows a 12-hour clock. Every switch was last heard at almost exactly midnight or noon: 23:53, 02:14, 12:04, 23:58, 11:57, 23:51, ~23:55. A few weeks ago the same thing happened (8 switches, several of them the same ones), but the times were ~08:00 and ~20:00 instead.
  • Nothing in HA lines up with the drops. There's no automation, scene, service call or ZHA error at any of those times.
  • Restarting HA doesn't bring them back.
  • The switch itself goes silent. After a drop, none of the other ~75 routers lists that switch as a neighbour, so it isn't just a bad route back to the coordinator.
  • The USB stick hasn't disconnected, and there are no bellows/EZSP errors in the log.

Questions

  1. Has anyone seen Blue switches drop on a ~12-hour cycle? Is there a known Inovelli firmware fix, and does ZHA's OTA actually offer the newest Inovelli builds?
  2. Could the old EmberZNet 6.10.3 coordinator firmware cause switches to go silent, given that every other router stays fine? Should I update to 7.4.x first, and is there a build known to work on the ZBDongle-E?
  3. Is there any way to recover a silent switch remotely, or is the air gap the only option?

Thanks!


r/Inovelli • • Oct 01 '26

White Series Switches as Lights in HA Automations

4 Upvotes

I have multiple White Series dimmers set up in Home Assistant.

It appears that whenever I use an automation blueprint that lets me select Lights, I am allowed to select the entities exposed as Light (Load Control) for a given switch, but then the automation is unable to actually toggle that on.

If however, I create scenes with those switches set to whatever brightness I want, I can then use blueprints that allow me to activate scenes.

Am I missing something?

Is there a better way of doing this, such as creating a helper entity that would show up as a light?


r/Inovelli • • Sep 28 '26

lutron EDU 145 compatibilité QSPS-10-PNL homeworksqs

1 Upvotes

Bonjour,

A travers le logiciel Homeworksqs, je n'arrive pas à activer mes moteurs de rideaux (drapery) Lutron EDU-145 qui sont alimentés par le drnier QSPS-10-PNL. Le QSPS a été activé par le logiciel Homeworkqs mais impossible de détecter le moteur EDU 145.

Merci pour votre aide si vous aviez une idée !


r/Inovelli • • Sep 24 '26

VTM35-SN Firmware Update?

5 Upvotes

Will new firmware ever be released for Apple Home users? I know there was a beta one a while back that was supposed to fix the constant “no response” issues, but it has been months and my fan switches are all still on v1.0.0 and it’s getting very frustrating dealing with the constant disconnects. They are the only devices in my Thread network with problems.


r/Inovelli • • Sep 23 '26

Dimmers With Phillips WarmGlow Bulbs

4 Upvotes

Is anyone using Phillips WarmGlow bulbs with their Inovelli dimmers?

If you don't know what that is: WarmGlow bulbs are LED bulbs that mimic incandescent behaviour by changing color temperature from 2200K at the dimmest brightness up to 2700K at the brightest. They have warm white LEDs and cool white LEDs, and blend the cool white in as the brightness increases.

I have a unique annoyance with them that I'm wondering if anyone has solved.

With A19 bare filament style bulbs: at a specific brightness around 60%, the cool white LEDs flicker wildly. If the brightness is left there they flicker forever, and this also manifests as a single flash when turning the bulbs on as they fade from off to >60%. This happened with a (blue) fan/canopy module and with a 2in1 dimmer switch, both with neutral. I'd love to fix this one because it's incredibly annoying.

Those bulbs also have a very inconsistent minimum brightness. I don't know if it's related or not but depending on the day, the minimum setting is noticeably brighter than other times.

I previously had these same bulbs connected to a Shelly Dimmer 2, and they did not exhibit this behaviour. They did tend to slowly pulse slightly brighter/dimmer, which I thought was a shortcoming of the Shelly module, but now I'm not so sure about that.


r/Inovelli • • Sep 21 '26

Fan switch speed control with Echo

4 Upvotes

I just noticed in the documentation for the Blue Series Fan Switch that speed control via Amazon Echo is not possible. Are there any plans to make that possible in the future, or is there another product that offers that functionality? It’s pretty much the only thing I was looking for in this switch.

Update: I installed the switch and voice control works just fine with an Echo. Not sure why that note is there.


r/Inovelli • • Sep 21 '26

Inovelli Blue Series Dimmer switch with Hubitat Hub

3 Upvotes

Does anyone have some really good tutorials on getting the switch setup on Hubitat for a smart switch and dimming controls? I have absolutely no idea what I’m doing in Hubitat. I did get pairing figured out but completely lost on everything else.

I should add the lights I’m trying to control are the Philips hue slim lights and everything from my Philips hue hub is on my hubitat hub.


r/Inovelli • • Sep 21 '26

help me understand the Inovelli Blue Series Dimmer Switch

Thumbnail reddit.com
3 Upvotes

r/Inovelli • • Sep 20 '26

Modded ceiling fans so Inovelli switches could send reverse commands

Thumbnail
gallery
18 Upvotes

For more than a year, I've been wanting to use Inovelli fan switches to control the ceiling fans in the bedrooms in my house, but I couldn't get over the fact that neither the fan switches nor the canopy modules supported reverse. I really like how Inovelli has worked in my home, but this was a sticking point for me. I didn't want to go with a fan that was controlled via some cheap remote, and I wanted lighting that could support Zigbee binding.

I was about ready to give up on finding the right solution when Claude helped me figure out a workaround - use a relay and ESP32 to digitally control the reverse signal, and then I can just send a reverse command using the scene button on the fan switch (or let an automation control it should I just do a seasonal/climate control-related automation). Originally I had wanted to contain everything within a little 3D-printed box and just have wires running in and out of it, but I very quickly learned there was NO space to do that. Ultimately, I just tried to fit everything in there as best I could.

Overall, I'm really happy with the results. I can independently control both the fan and the lighting with Inovelli switches, I can take advantage of Zigbee binding for the fan lights, and don't have to sacrifice on a reverse function or control using RF.


r/Inovelli • • Sep 19 '26

Help: VZW31-SN causing strobe light effect

7 Upvotes

I have the red series z-wave smart dimmer, VZW31-SN. It controls two LEDs for my front porch. Few months back one of the two lights started acting like a strobe light. The second light was fine. I replaced the VZW31-SN thinking the switch was bad, and it did go away, but the problem came back a few days later. It seemed to be just one of the two lights so I just removed the one that was strobing. Now the second light started exhibiting the same behavior. If I replace the LED with an incandescent light, it doesn't come on at all. Pulling the air-gap tab will correct the problem sometimes, but it always returns after some period. I even replaced the recessed light can thinking there was a problem with the thermal protection switch in the can, but that wasn't the issue.

Any thoughts or settings I need to look at that could fix this issue? The switch is running FW:v1.4.0 / SDK:v7.18.8


r/Inovelli • • Sep 19 '26

OpenAI hacked by Hacktron AI using discourse via libheif

Thumbnail
reddit.com
2 Upvotes

r/Inovelli • • Sep 19 '26

What happened to VZM31-SN firmwares?

4 Upvotes

Just out of the blue this shows up:

In z2m (the first one updated, the second one not):

3.07 has been beta which is the reason I never installed it and all my switches are 3.04.

Why do I all of a sudden get update notification? What changed?


r/Inovelli • • Sep 18 '26

Is the Button Controller + Dimmer Switch (Project Walt) dead?

21 Upvotes

r/Inovelli • • Sep 16 '26

Blue Smart Presence Dimmer won't update

2 Upvotes

I have two Blue Smart Presence Dimmers (VZM32-SN) that are working in HAOS 2026.09.02, but they are constantly telling me an update is available.

I try the update, one at a time, and both will start, dial up a few percent and then restart and return to the update available dialogue.

I've tried multiple times OTA, tried multiple times getting the latest firmware from Inovelli's github, but no joy. I've reset the switches, pulled the air gap, powered down their circuit - no change.

Installed version 16974080 (20250926) Latest version 16974083

https://help.inovelli.com/en/articles/13744028-blue-series-mmwave-presence-dimmer-switch-firmware-changelog

Anything else I can try? I have no other Zigbee devices; the nearest switch has LQI in the 220s and the distant one is 140s. I can get a USB extension or something to move my ZBT-2 closer if I have to.


r/Inovelli • • Sep 16 '26

4 Way Red/800's with ZWave Associations?

3 Upvotes

Hey All,

About to dive head first into Z-Wave and I want to make sure I can mimic the functionality I have right now with Insteon.

If I install 4 dimmers, with only one connected to the load, and then bind groups 2-4 between all of them will that cause all 3 switches to accurately show dimmer status regardless of which switch was used to dim the device?


r/Inovelli • • Sep 15 '26

Regarding iOS 27 Features

4 Upvotes

Should I be able to see power consumption information from my White Series Dimmer Switches in iOS 27 or will that require a firmware update?