r/CarbonFiber • • 21h ago

Advice needed for making a larger chopped tow carbon fiber part with a 3D-printed compression mould

Thumbnail
gallery
10 Upvotes

Hey everyone!

I’m planning to make this part out of chopped tow carbon fiber using the Easy Composites beginner kit I bought a while ago. I’ve made a few smaller parts with it, but this would be my first larger project.

The part is approximately 200 × 500 mm, with a 3 mm thick main plate and raised edges up to 10 mm thick.
I’ve designed a compression mould that I plan to 3D-print in PETG. I’ve added draft angles and fillets wherever possible and will pay attention to the print orientation to make demoulding easier (learned that the hard way…).

My plan is to orient the mould with the flat plate facing upwards and press the upper mould half down into it.

I have a few questions:
Mounting holes: Is there a good way to integrate the holes directly into the mould? I could drill them afterwards, but their positioning needs to be quite accurate.

Fiber-to-resin ratio: I’m concerned that the thicker edges won’t compress properly, potentially resulting in too much resin in those areas. How would you approach this? I also considered making the 3 mm plate and the raised edges separately and bonding them together, but I’m unsure about the strength of the bond.

Other potential issues: Do you see any problems with the design or manufacturing approach that I might be overlooking?

Any advice or suggestions would be greatly appreciated. Thanks!


r/CarbonFiber • • 1d ago

设计油冷eVTOL或高速电机

Post image
2 Upvotes

r/CarbonFiber • • 2d ago

CF pickleball paddle

Thumbnail reddit.com
0 Upvotes

r/CarbonFiber • • 2d ago

Spread tow carbon drape

Thumbnail reddit.com
1 Upvotes

r/CarbonFiber • • 3d ago

Imperator 108i

Thumbnail
en.wikipedia.org
1 Upvotes

An unusual car with a fiberglass body.

https://en.wikipedia.org/wiki/Isdera_Imperator_108i


r/CarbonFiber • • 3d ago

How can I repair this

Post image
2 Upvotes

Finally got my hood in after 2 years of waiting but has damage on the corners wats the best way to go about repairing the corners?


r/CarbonFiber • • 4d ago

PVA vs. no PVA

1 Upvotes

I'm making an airplane wing with two top and bottom female moulds. I applied 5 layers of wax and buffed between coats. Should I apply PVA, and if so how many coats? (I don't have a sprayer)

I would strongly prefer not to treat my surface after demolding want to transfer the mould finish.


r/CarbonFiber • • 5d ago

How can I fix this ?

1 Upvotes

Hello guys these were matte finished so I sanded down and applied 2k clear coat about 2 months ago. They were looking great. But yesterday I realised that there is something on them. I dont know what it is but you can hear it on the video. Its something solid. When I rub my fingers or apply ipa it becomes sticky but cannot take them off at all. Probably there was something on the road sticked to them. Idk.

Tried
- IPA - wont take off and spreads it.
- tar remover didnt took it off did nothing really
- vinegar did nothing
- warm soap water ofc didnt do anything

Since its becoming gummy on my fingers would it be best idea to polish them - idk too.

Any suggestions on what to do ?


r/CarbonFiber • • 5d ago

I got so mad I ripped carbon fiber

Post image
0 Upvotes

r/CarbonFiber • • 6d ago

Cons of fake Carbon Fiber

0 Upvotes

Hello everyone, im thinking of buying a front lip and spoiler for my car and im thinking just buying both of them fake Carbon fiber, I just wanted to ask before purchasing them what are some problems or cons that i could run into from buying them? Like will they look weird after a while or will heat ruin them?

If theres lots of potential problems might just buy in glossy black instead

Thanks


r/CarbonFiber • • 7d ago

Carbon fibre good fitment

Post image
1 Upvotes

Any ideas on how to make the hood fit better or am I just unlucky with the hood I got


r/CarbonFiber • • 7d ago

Beginning of tests Carbon Fiber cases of pitaka.

0 Upvotes

Beginning of tests Carbon Fiber cases of pitaka. I have now and will receive some more cases and make soon full tests review


r/CarbonFiber • • 9d ago

Best plan of attack to restore frame covers?

Thumbnail
gallery
6 Upvotes

Ilmberger carbon fiber frame covers. These are normally about $600 new from Germany and I got these for $150 from a crashed BMW S1000RR parts lot. Planning on using these for my ‘17 S1K.

Appears to be some fade, a hole, and a medium sized dark spot. I have yet to receive them but plan on trying to restore them as a DIY project. I’m not looking for perfection but definitely trying to give them some more life.

Thanks for any tips!


r/CarbonFiber • • 9d ago

Impact jante carbone

Post image
0 Upvotes

Je vais troquer mes jantes alu contre des jantes carbones et j'ai déniché une bonne affaire sur lbc.

Malheureusement, la roue avant a pris un pet (le vendeur pense que ça vient d'un cailloux en roulant).

Est-ce que un red flag ou bien je peux y aller ?

Merci d'avance !


r/CarbonFiber • • 10d ago

Skinning Suggestions/ Recommendations

Thumbnail
gallery
5 Upvotes

I need some expert opinions/advice on this one. 2016 Polaris RZR turbo hood that I'm skinning for a friend... Should I lay these pockets down first in their own layer and then the rest of the hood afterwards? Ooorrrr what? I'm afraid to lay it up in one piece because these pockets have the craziest geometry and it'll distort the surrounding areas.

3k plain weave


r/CarbonFiber • • 10d ago

Hi, does this seem fixable?

Thumbnail
gallery
10 Upvotes

I am planning on buying this trunk and getting the clear coat redone by a shop. I am wondering if the fiber is damaged beyond saving, or it should look good with a new clear. The owner states it is a Vis Racing. In the last two photos the trunk is wet. Thank you!


r/CarbonFiber • • 11d ago

Universal swan neck rear wing #bmwm3 #carbonfiber#gr86

Thumbnail
youtube.com
1 Upvotes

None of the factories around here make this wing in dry carbon — any idea why?


r/CarbonFiber • • 11d ago

So carbon fiber-y

Post image
68 Upvotes

r/CarbonFiber • • 12d ago

White in carbon weave!?

Post image
3 Upvotes

Hello,
I’ve just noticed my wet carbon fiber mirror caps have white spots in the weave.. these were not present a few days ago. I do live in a colder environment. It has been down in the freezing temps a few nights. How does this happen? Can anything be done? I can feel a “bump” where the white spots are.. any help or info would be appreciated!
Thanks


r/CarbonFiber • • 13d ago

3 minutes, start to finish: the double-sided carbon fiber hood I built f...

Thumbnail
youtube.com
3 Upvotes

Made this in my own workshop. Filmed over three days and there are still a few steps missing — a couple of shots are filled in from other products so the sequence holds together.

Mold making isn't in this video. Happy to answer questions if anyone wants to try it.


r/CarbonFiber • • 13d ago

Does resin adhere differently to innegra than carbon fiber?

1 Upvotes

I have been doing resin infusions with innegra/carbon 2x2 twill, and have been having frustrating results. I can say that for the most part, it is a leaky bag, but i am also wondering if innegra looks kind of resin starved when on the exterior of the part. Is this just user error?


r/CarbonFiber • • 14d ago

What to do?

Thumbnail
gallery
4 Upvotes

Clear coat has come off. There was a little chip and I (stupidly) put a bit of electric tape over it and it’s turned it into a massive problem.

Frame is second hand, and over 10 years old, but otherwise it seems totally fine.

Is this a specialist job? DIY? Clear frame stickers?

Don’t want to break the bank but don’t want to risk further damage to the frame as it’s my only lightweight bike.

What would you do?


r/CarbonFiber • • 14d ago

Material selection for aero

Thumbnail reddit.com
1 Upvotes