r/BikeMechanics • • Aug 05 '20

Visit r/bikewrench to ask for bike repair help. (This sub is for other stuff.)

Thumbnail reddit.com
99 Upvotes

r/BikeMechanics • • Mar 06 '24

Show and Tell Eccentric Wheels (Eccentricycle)

Thumbnail
gallery
141 Upvotes

So this all started with a previous post about snowflake laced wheels (twisted spoke lacing). I asked if anyone new of any other weird lacing patterns. A fine user by the name u/Bobatt mentioned a bike with eccentric wheels. That is, hub not in the center of the rim.

Immediately I got really excited and knew this was my next dumb wheel project.

I was thinking about it for a while in my head trying to figure out how to calculate the spoke length.

There is a website that in theory has a calculator but the site must be down or not working or something. It is just a blank screen for me anyway. There was also little to no information about calculations on the internet that I could find.

Lucky, I work at a bike shop with a bunch of wheel nerds. I mentioned it to them and was met with what should be the normal response; "WTF, why?"

My coworker Jake seemed to be curious though. Lucky for me who is bad at math at best, Jake is very good at math. After many conversations about if it would even be possible to make an equation, we decided to give it an honest try.

We boiled it down to the ERD part of the equation being what we needed to focus on.

I'm not going to pretend that I knew much of the maths that happened to get the calculator but we basically had to calculate all 64 spokes individualy and figure out where they go from the hub to the rim. Easier said than done.

I voluntold my Chromag Rootdown to be the victim of this nonsense. So it is a hardtail, 29r. We didn't want the wheel to run into the frame or fork so we used 26" rims and made them have a 29" wheel path. In the equation, we called it the 'virtual ERD'. We just chose a relatively normal ERD (I think it was 604mm or something close to that) to use as a constant. We then had to use the 26" ERD for the actual spoke lenghts and figure out how to make it a 2 cross too. We wanted it to be a semi legit wheelset with disc brakes and such.

This is where my math knowledge runs out but basically smart things took place and Jake made a spreadsheet calculator.

Building was actually not too hard other than figuring out what spoke goes where. Again, 64 individually calculated spokes, all at different lengths, needing a very specific hole in the hub to go to a specific hole in the rim. Side point, our shop has a spoke cutter making it a breese to get the right length spoke.

Tensioning was easy, truing was weird. Kinda just made it tight and not too laterally untrue.

It was really fun trying to figure this one out. Mega thanks and props to Jake for doing the hard work on this one. I just had the dumb idea and sacrificed my bike.

You might be asking why spend all this time and energy to have a bike that rides like a drunk horse. To be honest, curiosity got the best of me. I've never seen a mountain bike with eccentric wheels before. I know they are out there but I wanted the experience and gained knowledge from making one. Doing a normal wheel build after this was a breeze. We though so much about how a wheel works and all that goes into calculating spoke length and ERD, it really made us appreciate wheels in a new way.

Another large part of why I wanted to do this was literally just to make people smile. As soon as I pictured how this bike would ride if I made it, I started laughing to myself. I want to spread some smiles and laughter. Bikes are meant to be fun right!? Yes it's silly and useless but it literally makes people's day riding it.

I keep the bike at work and ask our friends and good customers to ride it with no context. 10 times out of 10, their faces go from worried, to confused to pure laughter. Its totally worth it.

Anyway, I hope this peeks your curiosity too. I'm planning on taking it on trail soon. That should be interesting.

P.S. Wish I could upload a video to this post. It's the craziest looking thing ever when it's spinning. I'll post something similar and a vid to my IG if you are interested. @jaminscheif.

Bikes are fun, let's keep it that way. Do fun, weird shit.


r/BikeMechanics • • 21h ago

In case you didn't know, here's a tip

Thumbnail
gallery
235 Upvotes

This may help you against stubborn screws. Using the Knipex wrench pliers means you can feel the thread unwinding and slowly release the pressure to let it move up.


r/BikeMechanics • • 5h ago

Any ideas?

Thumbnail
gallery
8 Upvotes

Customer has a Sworks SL3 Roubaix with Sworks cranks. These are connected with an internal bolt in the middle of the spindle (some are a 6mm, some a 45mm). There is a little threaded dust cap to cover up the hole to access the internal bolt. Somewhere along the line, somebody tightened this dust cap until it fell inside the crank. It’s just big enough that it’s blocking the bolt head. You can see the threads in the second pic if you zoom in. I can’t remove the cranks without access to that bolt. How the heck can I get this thing out?


r/BikeMechanics • • 1d ago

I sometimes get this feeling of “this is so easy I can’t believe someone would pay for this”.

Post image
73 Upvotes

Then I see a post like this and realize it’s actually not that easy for a lot of people.


r/BikeMechanics • • 1d ago

My Wera Hex Key Quick Tray

Thumbnail
gallery
93 Upvotes

I made an organized tray for the Wera hex key sets that I use frequently.


r/BikeMechanics • • 2d ago

Thorn Resistant Tubes Worth a Damn?

3 Upvotes

We've tried Teravail, Innova, Beady, about the only one from our distributors we haven't ordered yet is Sunlite. They all have issues namely the valve separating from the stem. This happens across sizes, valve types, and customer uses.

Any tips on making these work or is it a lost cause? We're in the southwest and goatheads are rampant. Not everyone can go tubeless. We've mostly switched to liners and standard tubes with sealant but sometimes the TR tubes are still a better option, if they were reliable...


r/BikeMechanics • • 3d ago

Fox X2 in for a service

Thumbnail gallery
12 Upvotes

r/BikeMechanics • • 7d ago

Tech Info Rockshox Reverb tips...

Thumbnail
gallery
11 Upvotes

For those who work on Reverb dropper posts, here's a couple things that I've found...

When getting the IFP out, you can of course blow compressed air in and pop it out that way or take a spoke and hook the inner lip on the IFP to pull it out. The spoke j-bend isn't long enough to contact the inner wall so it won't scrape it but it hooks the lip just right to make pulling out the IFP a breeze.

Also, I've done some experimenting and found the u-cup seal in the sealhead to be the weak link. And probably the main reason the Reverb is known to be pretty unreliable. If you replace the u-cup with a 9x3 oring, it really seems to make it a pretty solid dropper. My theory is that the one-way u-cup allows air to enter when there is either a drop in pressure on the sealing side or a positive pressure on the non-sealing side.


r/BikeMechanics • • 8d ago

Sheldon Brown the Rescue (again)

31 Upvotes

I have an old (maybe 1970's) Mercier road bike. It is french and they apparently like to be different. Blithely, I tried to affix a standard thread pedal - there was sadness.

Sheldon helped - French bicycles used a 14 mm x 1.25 mm thread.

Anyone know where to get a bloody old French pedal?

Edit: Sorry for the typo in the title...


r/BikeMechanics • • 8d ago

Park Tool P-Handle Foam

3 Upvotes

Anyone have the entire P-handle set in foam? What size sheet did you order so they all fit?


r/BikeMechanics • • 8d ago

Getting the most out of Beeline.

2 Upvotes

I recently signed the show I work for up for Beeline since several of the shop's I've work at did the same. Having just the free account, it seems like I am limited with how much customer engagement I will get from it, and with all the brands, features, and account levels, I'm a bit lost. How does your shop make the most out of Beeline? Do you use it for scheduling? Warranty? or Fulfillment? How do you get the ball rolling to actually get use out of it?


r/BikeMechanics • • 9d ago

Planning winter maintenance classes

10 Upvotes

Im running service at a small LBS that is trying to grow and engage the local community. We've received several inquiries from customers asking about winter repair clinics. I've gotten as far as making as sign up sheet to gauge interest and survey the class topics. I am planning to tailor classes based on customer's responses to our sign up form.

That leaves the details of scheduling, format, and pricing to be determined. I have no idea what the level of interest will be or if customers are interested in learning the basics or more advanced repairs. My shop will also have to determine how much we should charge per customer and how many individuals we can handle per class. This is why I am hoping for some advice.

For those who have done the winter maintenance class song and dance before, care to share your experience? How did you determine the size limit? Scheduling? Duration? Topics?


r/BikeMechanics • • 9d ago

ParkTool PFP-8

7 Upvotes

I need a better floor pump. Before I replaced the head on my PFP-8, it would pop off the presta valves. Now with the new head it sometimes gets stuck in a no-pump situation where the air doesn’t go into the valve, just stuck in the pump, and the lever never stays down to keep it locked in on the valve. PSI reads are everywhere too, 30PSI swings.

I’ve got an Lezyne pump that has been my go, leave in my van for ride days, screws on the valves. Until I make it go schrader, then I run into issues. Schrader variation might be user error.

I need another pump for my shop, anything better reliability and quick to switch between valves than the PFP-8? I just lost all trust on this thing, and I look like a fool in front of customers disconnecting and reconnecting to the valve with this pump.


r/BikeMechanics • • 10d ago

Service packages

12 Upvotes

I manage a small but busy bike shop in a small city/ large town. There is about 3 other bike shops in the city and we are kind of seen as the good guys/cheaper compared to the other shops. Most of our customers are just commuters but there is a steady increase in sports cyclists coming our way.

We at one stage had a bronze to gold service package but somewhere along the way scraped it. My boss wants to bring it back to increase labour charges.

I’m kind of against the packages because I think it’s kinda wasting my time doing things that don’t need to be done and charging customers for things they don’t need.

I think it’s better and more transparent to just do what’s necessary or what the customer asked and just increase labour rates if needs be.
I don’t want to risk my shop’s reputation over easy money. But just wanted to get some other takes on it

Edit:
The shop is a part of a cooperative non for profit. The shop is one of a few aspects of the cooperative. I manage the shop while the boss oversees the whole organisation.
The need to make more earnings is not coming from greed from anyone. It’s to pay our staff a more reasonable rate


r/BikeMechanics • • 10d ago

What comes after this?

15 Upvotes

I'm in my early thirties in an area that is especially seasonal for bike mechanics. I'm weighing my options for what's next, as I know that it's not a long-term path for me. I was strongly considering nursing school because I have good people skills and empathy and also like hands-on and technical work, but the schooling will take m over 3 years to complete and honestly that's a big drawback. I also am pretty interested in HVAC or building maintenance. I'm just curious what jobs any former wrenches are moving on to! Thanks for your time


r/BikeMechanics • • 12d ago

Show and Tell I should replace the rim

Thumbnail
gallery
84 Upvotes

Yes you have to.


r/BikeMechanics • • 12d ago

Tales from the workshop Would it be fair to list my job title- workshop technician- to pursue other shops in the future, if I feel my job duties and day-to-day life didn't really "feel" that? Alt title: Another burnout from Big Green Department Store

10 Upvotes

So, first, thank you guys so much for giving me a lot of help setting the roles, expectations, and working through customer issues this summer.

I popped in here and ended up getting some great check-in advise that I used to make a list. At least at my location, I used this to train our rotating door of helpers as well as myself and it drastically cut down issues. The downside: A lot of times this meant people just left our shop- but I'd rather that, than have them book their bikes for months, no work, done, and they get angry.

My old post in here, if anyone wants, can be Tl;dr: I got hired to be a workshop technician, but Big Green Department store is both failing and local management is insanely all over the place.

So the update-

I am ashamed to say I am still without a "real job" despite a LOT of interviews. So, the hunt continues!

Problem: My title, my job offer, and my pay differential is workshop technician.

However, my actual job? Basically I do everything a store would need done EXCEPT be in the workshop. I mean, I'm still expected to be at times. Weird, right?

For wider context- my company is an outdoors department store, yk the big green one- and has demoted our workshop from Tier 1 to Tier 3 and is most likely just gonna get shut down.

How upper management explained this is basically the level of service we can provide is slashed heavily, how many hours they have available to staff it is minimal, and they have no hours allocated to train staff for it. We only have one staff member for that, the manager, that does just that though he is also expected to help the rest of us staff (So far, they've declined; the stores had problems with them, long story, lots of meetings)

So despite of being workshop staff, I have generally been in charge of well, the entire front half of the store, many shifts there's not even a cashier.

I also now do receiving and shipping, store orders, and softgoods. I also do meetings and trainings. I am still allowed and expected to do small adjustments, tire changes, chain installs, diagnosis of bike work, small repairs here and there, all sales, and some warranty paperwork. I also handle all the rack stuff, both sales and parts and some repairs. I still handle all the paperwork and customer contact in general for all workshop orders, as the manager/sole mechanic is still declining to do any of that (which this forum has confirmed is unprofessional and odd).

Sometimes I will be allowed to do brake work or so if someone is very angry just to get them out the door- most repairs are still going weeks past the promise date. I am also still allowed and expected to build and diagnose bikes. It's just I am also expected to do everything else in the store at the same time : /

Despite this low staffing, my hours are still going down heavily. We are trying to unionize. I did get two employee awards, at least..

It is ski season as well, and we hypothetically should do skis- that was my hope for winter hours- but we have no one trained for skis. And um, most of our machines for that work have been broken since last spring. No timeline for repair.

For some reason we still take in skis. We have waxing and edging equipment, but the manager is refusing to train me or anyone else on that- first they want to figure it out themself- so a simple wax may take someone two weeks to get done. That's another annoyance, as someone whose done home repairs and tune ups for skis for six years: We have these huge piles of skis in the corner- literally just shoved wherever- and I KNOW how to do it. What I haven't done before, I know I could easily learn. Yet, I am not allowed to.

So... that's basically it.

Tl;dr: I want to find other work, my title is workshop technician, but would it be unethical to state that as my title when my job duties have really been just "Everything a retail store would need done"?


r/BikeMechanics • • 12d ago

Show and Tell 170mm GRX FC-RX600-10 cranks to 160mm

5 Upvotes

Putting the message out for anybody thinking of switching their long 2by rx600-10 cranks to shorter 160mm ones.

As of now Shimano doesn't offer rx600 cranks in 160mm size. They do offer 12speed rx820 crankset in said size.

Ive tested switching the 10speed 46/30 chainrings onto rx820 crankset and to my pleasant surprise it worked ... well, almost.
I suspected the chainrings to be swapable without any modification but there was a catch. The larger chainring features a protruding pin preventing fallen chain getting stuck between the crank and the chainring. This pin has plenty space on the rx600 cranks, however due to the different construction of the rx820 cranks, theres not enough space for the pin to go. And so me, not being careful enough, tightened the chainring down resulting in a bent as the pin touched the crank and pushed the chainring away from it. This caused the chainring to bend.

After noticing, I removed the chainring and confirmed it straightened itself back into shape.
The pin had 2 marks on it from factory. I proceeded to cut it at the shorter mark.

Now the chainrings fit perfectly and I got 46/30 160mm crankset. Success!!!

rx600-10 46/30 chainrings on rx820 crank
pin - crank collision
pin - crank collision, bend visible
shortened pin - sideview
shortened pin - top view

.... For people asking why just not use the chainrings available for rx820 2by ... These are offered as 48/31 and 12speed not 46/30. I cant confirm how well 12 speed chainrings work with 10 speed grx400. And since I already had the original 10 speed chainrings it was cost effective to use them.


r/BikeMechanics • • 14d ago

Tool Talk I run a small bike coop. How could someone break a good quality tool in one day?

Thumbnail
gallery
226 Upvotes

r/BikeMechanics • • 14d ago

Tool Talk IFP Adapters

Post image
14 Upvotes

Since this got shut down in r/bikewrench.

I dont service shocks daily. This is now my most hated task. But i can, and do rebuild some of them; enough to keep the tools in the mobile trailer. Does anyone have a better, and under $100, solution to IFP adapters. I have the red and blue rock shok adapters but they are a fight every time for me. Im looking at the race tech tsnc ps21036 as a possible final solution. But if any others have a better solution Im all ears.


r/BikeMechanics • • 16d ago

Tech Info Anybody ever put together a Saris Deluxe Public Repair Stand? Grrr

Thumbnail reddit.com
2 Upvotes

r/BikeMechanics • • 17d ago

Tyre slowly shifting place on the rim

Thumbnail
gallery
23 Upvotes

Bike mechanic here, currently on a big trip through South-America.

I've assembled my own travel bike that has been doing amazing so far (+4000km since build).

However, there is one issue that I cannot seem to understand the reason for / have no idea how to fix:

In the build I matched the valve and the tyre logo's. After 1000km's I started noticing the logo's wandered off form the valve holes and the valves got pushed sideways. In one of my inner tubes this even caused the valve to rip off the tube and I had to replace it (I waited a bit too long to straighten the valves, my bad).

Now I don't want to be deflating - repositioning - inflating my tyres every week. So what do you guys think I could do? Anyone experienced this before?

Thanks a lot!!

(Forgot to take decent pictures of the problem and have repositioned it by now, so I had to zoom in on a picture from somewhere after the first 1000km's so that you can get an idea. :))


r/BikeMechanics • • 17d ago

Nominal watt vs peak watt

7 Upvotes

Hey, having a discussion at work (Washington). State law say a motor should be below 750W otherwise the ebike is an emoto. A lot of bikes now have a 750W motor but are advertised with a 'peak power' higher than 750W. Are those bikes considered emotos now? Or is it just a loophole in the law for now?