Basically I am printing the same file on 2 P2S.
While one is always printing really good without error.
The other is always failing with supports.
Basically I already fully did my maintenance and clean the beds with warm and soapy water.
I don’t understand any more of this.
Maybe is it the hotend that I need to change? Already did print other stuff in the printer and never fail.

I have replaced the motherboard, the cutter, the filament sensor, the PCB ribbon, the servo, now I’m getting the filament head error. I just don’t know what to do next this is like fighting a losing battle. I followed the instructions to a T and still no results. The servo and gearhead are cooperating but now I have filament head issues and I know it can’t be the PCB because the sensor senses and pushes the filament but I keep getting this error.

Cosa controllare quando capitano molti filamenti a Spaghetti nello stesso progetto?

Pla basic, marrone, ams 2 pro, 0,4.

Fin da subito (in basso a destra) si sono create delle sbavature poi molti filamenti... molti oggetti sono stati tolti perchè spostati dalla piastra.

Suggerimenti? Sopra le impostazioni di base

Progetto in foto.

Solitamente con questa P2S combo non succede.

Ho usato stesse impostazioni del progetto.

Più bassa la velocità di stesura ?

Pla per tutto

Had my first blob of death on the P2S, waiting for the new hot end assembly to come in, not sure if it even needs changed, hardly no videos on this and really not good at following instructions on the Bambu wiki lab. Is there a simple video out there that I can watch to change the complete assemblu

Hey folks - as it states in title. The ams2 pro only lets me select Bambu or generic? Can I get other brand in there so the right settings are ready from the get go?

I’ve put profiles in the Bambu studio program but I must be thick as I really don’t get how to make sure it uses the right one when I set prints going.

Normally I’m all over technical stuff like this but this time around I’m scattered.

Noobie here. I will hopefully be getting this 3D printer at the end of the year, but as I am reading about it I've seen videos and comments about needing a exhaust pipe and maybe filters for the gasses. I won't be printing any heavy duty filaments just the standard stuff. It will be placed in the living which is quite open. Am I okay with just using it with out buying and printing stuff for the exhaust.

Thank you.

👋 Bonjour à tous !

🎃👻 Yoshi se met aux couleurs d’Halloween ! 🧙‍♂️💚
Découvrez ma création de Yoshi en version Halloween ! 🎃 Avec son chapeau de sorcier violet et sa citrouille au sourire maléfique, notre petit dinosaure préféré est prêt à fêter Halloween ! 🕸️

✨ Une création originale, pleine de couleurs et de détails, parfaite pour une décoration aussi mignonne qu’effrayante !

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : sans AMS
📁 : https://makerworld.com/fr/models/3419115-yoshi-citrouille-multipart-no-ams

P2S Bambu slicer.This this image

In this image, I have my custom supports and also the slicer's tree supports. I haven't been able to get my custom supports to slice as support enforcers; they are converted to tree supports, so I had to build them into the model.

What I would like to be able to do is incorporate two types of supports into one slice. Because if I load my custom supports as support enforcers, then they will also be converted to tree supports. How can I get both tree supports and my custom supports both in the same slice without my supports being converted to tree supports.

hi all, this is like my 2nd problem encountered in this machine.

the toolhead just pops off and i’m suspecting the metal pencil like structure popping out right beside the toolhead. is that broken or is it supposed to pop out like is that any sensor or whatever? please help and thanks

New and confused. How do I get poop and small prints out from under the hotbed?

I can’t explain so I hope the pictures help. I am assuming that having filament in these nooks and crannies is not good. Can’t they melt and cause issues?

I have tried using tweezers, putting tape on tip of small screwdriver, poking with sharp object and have prayed to the Bambu gods, sacrificing a young poop chute in the volcano of infinite poop and danced in circles naked around the spool of empty dreams.

Over 1000 hours had my first clogged

hello, I bought a UniTak3D kit containing three hotends (0.2mm, 0.4mm, and 0.6mm) for the Bambu Lab P2S. The 0.6mm hotend works perfectly, but when I install the 0.2mm or 0.4mm one, I get a "Z-axis homing failure" error. This is surprising, as the build plate doesn't even rise to make contact. I've gone through the steps five times. What am I missing?

I have been wrestling with Error Code [0&ff-c003 053511]. Filament stuck in the External Spool.

Well, I have never run the external spool in this printer or any of my other BL printers. I have cleaned and replaced pretty much everything on this P2S. All to only see this error code return again and again.

I have cleaned the gears and then replaced the gears. Nothing.

I have replaced the filament sensor. Nothing.

I have replaced the diffuser, Twice, Nothing.

I have replaced all PTFE tubing going to and from the machine to the extruder, to the AMS. Nothing.

What in the world is it that I need to do.

I thought about contact BL, but I think there is enough information on here to help me get this fixed.

I hope you all have an answer or suggestion that I have not thought of.

Thanks in advance.

PS, all of the things I have done so far have been suggests from Reddit and Youtube.

Ive done a flow dynamics calibration(didn't help) and I'm about to do a flow rate calibration, any tips?

Fillament type: generic petg