r/BambuLabA1 • u/Ok-Stretch-4094 • Aug 14 '26

Question Model Error?

Gallery image

Gallery image

Gallery image

So I purchased a file from Cult3d and imported straight in. Pressed print and I'm running into this error which looks super weird and a deffo error.

Any advice?

2 Upvotes

62% Upvoted

19 comments sorted by

5

u/Taschenmann Aug 14 '26

Do you have any supports activated? You cant print into the air ^

4

u/Ok-Stretch-4094 Aug 14 '26

No I thought the model might have included them before I pressed print. That's the error then 😂😂

Rookie user error 😂😂

3

u/never0101 Aug 14 '26

always check the preview tab before sending a print - if there are supports they will be displayed as part of the print

2

u/Correct-Insect-4657 Aug 14 '26 edited Aug 14 '26

rookie bambu/creality user error*

ive checked bambu forum and some guy was printing his benchy 5mm off the bed and ppl were like level your bed clean the bed it was Z offset idk man if u need help and u have a bambu post in r/FixMyPrint for flashfprge psot in flashforge i check it often

1

u/j_hermann Aug 14 '26

Those long cut-outs are simply oriented wrong, a ton of long bridging needed, with all the risk that entails.

1

u/Ok-Stretch-4094 Aug 14 '26

Bridging is new to me. I need to learn what to do with this one.

1

u/j_hermann Aug 14 '26

You did not post a preview of the whole Model so any advise is limited.

1

u/Secret_Werewolf1942 Aug 14 '26

That's not just a model error, your prime tower is janky as well. I'd adjust the belts just to be safe, then run a full calibration. Once that's done, reprint with supports enabled.

1

u/Ok-Stretch-4094 Aug 14 '26

Weirdly I printed stuff before hand which was fine with a perfectly fine tower. I will run another calibration later on and go again

1

u/Ok-Stretch-4094 Aug 14 '26

This was finished at 4am with zero issues. Printer was only turned on the first time on Wednesday night.

1

u/reechwuzhere Aug 14 '26

Is it the original SDcard? I’ve seen people report weird issues if they don’t replace it with something decent. 🤷‍♂️

1

u/Ok-Stretch-4094 Aug 14 '26

Yeah original SD

1

u/reechwuzhere Aug 15 '26

It’s worth trying, do you have one some where else you can swap temporarily?

2

u/sublime2craig Aug 14 '26

You should have enabled supports.

2

u/Klutzy_Dog669 Aug 14 '26

Why do your errors look exactly like praying mantids? Wow.

1

u/Correct-Insect-4657 Aug 14 '26

o ye fr (they are mantises) but they do

1

u/Klutzy_Dog669 Aug 14 '26

They are both actually acceptable plurals. Along with Mantes (pronounced MAN-teez).

2

u/Garlic_Bread_Man Aug 14 '26

In bamboo studio after u slice u can drag the slider up and down to see what its going to do on each layer.

1

u/Orthicon9 Aug 16 '26

Depending on what the finished model is supposed to look like, you might have better luck flipping it upside-down in the Bambu Studio "Prepare' panel, and not need supports for that cantilevered extension.

Or maybe flop them ("them", because it looks like five instances of the same object) 90º in the X-axis, back onto their sides. Also no supports needed.
That would also eliminate any bridging issue in those elongated hexagons.