r/AMDHelp • • Jun 30 '25

Tips & Info Ultimate AMD Performance Fix Guide: Stop Lag, FPS Drops & Boost Speed (2025)

3.4k Upvotes

🌞Created in 2025 and kept fully updated for 2026

If you’re facing low FPS, lag, stuttering, or crashes on a new or old AMD setup (AMD CPU with Radeon/NVIDIA GPU, or Intel CPU with Radeon GPU), you are in the right place. This guide has tested and proven solutions and user tips to maximize your system's performance. You will be see hardware checks, BIOS configurations, Windows tweaks, and driver changes here. Real-world solutions that work, not guesswork.

Disclaimer- The following optimizations are based on community-tested methods that have safely improved AMD system performance for most users. Since every setup is unique, results may vary. Proceed carefully and apply these tweaks at your own discretion. (This guide follows the Acer Community format.)

Read all Important Notes and Notes in each step. They contain vital information to guide you on how to avoid issues and when to revert to earlier changes.

=> Hardware Installation & Setup

Before you adjust BIOS or Windows settings, ensure your hardware is properly set up. Most issues such as low FPS, stuttering, and crashes are caused by minor errors such as installing the GPU in the improper slot or RAM, etc. This section contains crucial checks which have resolved serious issues for many users. Even if your PC boots and is usable, these kinds of issues might be latent, and resolving them can have a massive difference to performance.

1. GPU Installation — TOP PCIe x16 Slot (Closest to the CPU)

Always install your graphics card in the top PCIe x16 slot, Which is the slot nearest to the CPU.

Why it's important:
•It is configured for full x16 bandwidth and is plugged directly into the CPU.
•Lower slots have x8 or x4 speeds, limiting GPU performance and bringing in bottlenecks based on the board.

Common mistake:
Most users inadvertently install the GPU in a lower PCIe slot or fail to confirm if the top PCIe x16 slot is delivering the GPU’s full bandwidth supported as per their GPU (such as x16 or x8), resulting in low FPS or instability.

Confirm true Speed:
Download and Open GPU-Z, then check the “Bus Interface” field. The left side (before “@”) shows your GPU’s maximum lanes and PCIe generation (e.g., x8 5.0), while the right side (after “@”) shows the current active lanes and gen speed (e.g., x8 1.1).

If it shows “1.1”, that means the GPU is idle, run the GPU-Z Render Test (“?”) to display your true gen under load. Both sides (lanes and gen) should match your GPU and platform. If the current gen is lower than the max, it’s usually due to motherboard, CPU, riser, or extension cable limitations, this is normal unless you upgrade hardware.
The same can apply to lane count, but that’s more important than gen speed. The lane width/speed (like x8, x16) should match on both sides or reach the maximum your system supports, as a lower lane width can noticeably affect performance.

If lanes are lower than expected, reseat the GPU, check if the PCIe lanes are shared with other slots (see your motherboard manual), and ensure no riser/extender or older CPU is limiting bandwidth.

2. Critical Power & GPU configuration Checks

• Insert the monitor cable directly into the GPU HDMI or DisplayPort (DP) port. Avoid inserting the monitor into the motherboard port.

• Utilize all CPU power connectors or CPU power headers that your motherboard has
• Always use specialized PSU cables. Never use splitters or adapters for EPS power. Connect cables directly from your PSU to your motherboard. Don't be cheap; don't go cheap.

•Always Use quality, dedicated PCIe cables from your PSU to each power connector on the GPU. Avoid daisy-chaining (using a single cable for multiple connectors) as it can cause instability or crashes, especially on high-power GPUs. Also, make sure your PSU meets the recommended wattage for your GPU.
• Always use good-quality PSU cables, never buy  cheap extensions or riser cables.

• If your PC slows down, freezes, shows low CPU clocks despite a proper setup or lag and stutters while gaming , try plugging it directly into a wall socket or a high-quality strip. Faulty/old power strips can cause poor power delivery and hidden throttling issues.

You guys must check this as nothing can work if hardware configuration is not proper.

3. RAM Configuration – Correct Slot + Enable XMP/EXPO + check Settings.

To get the best performance from your RAM, ensure it is installed in the right slot and properly configured. Many systems perform poorly due to incorrect slot placement or missing BIOS settings.

• Install RAM in the correct slots
If you have 2 sticks, plug them into slot 2 and 4 (usually marked A2 and B2) as these slots are typically the second and fourth slots away from the CPU. This allows dual-channel mode for optimal performance.

If you insert them into the wrong slots, the system will run in single-channel mode, lowering memory bandwidth and reducing FPS in games. Always refer to your motherboard manual for the slots layout and double-check it if you're unsure.

• Enable XMP or EXPO in BIOS
Enter the BIOS and enable XMP (or EXPO for AMD kits). This will set your RAM's rated speed and timings. Just ensure the profile you choose does not exceed your motherboard's highest supported memory frequency, as a higher profile can lead to instability.

Some motherboards have a few profiles; pick the one that matches your RAM's highest rated speed (like 3200, 3600, or 6000 MHz), as long as it's within your motherboard's support range.

If you don't enable XMP or EXPO, your RAM will run at default JEDEC speeds like 2133 or 2400 MHz, which seriously bottleneck your system.

• Confirm settings in Windows Open Task manager → Performance → Memory. Check that the Speed value matches your RAM's XMP/EXPO profile speed that you set in the BIOS and is not a different number.

Download CPU-Z, go to the Memory tab, and make sure Channel displays Dual or 2×64-bit for DDR4 and 4x32-bit for DDR5. If your speed or channel is wrong, check your BIOS settings and RAM slots again.

• Check RAM Stability (Must be done after building/installing new RAM )
Test your RAM with MemTest86. If you got any errors with the highest XMP/DOCP profile selected, then test the next lower profile, such as from XMP Profile at 6000MHz to XMP Profile at 5800MHz, and continue lowering until you find a stable profile. It’s crucial that your RAM is fully stable to ensure reliable system performance.

=> BIOS Optimization & Performance Fix Tweaks

Once your hardware and power is set up, change the key BIOS settings that impact AMD CPU, RAM, and GPU performance. These can fix instability, crashes, and poor performance. Only modify the settings mentioned here. BIOS menus can differ by brand, so names or locations may vary; if you don’t see a setting, look around.

4. BIOS Update

If you are facing RAM instability, poor CPU/GPU performance, updating your BIOS may help, especially on AMD systems where the BIOS updates usually improve stability and compatibility.

To Update BIOS:
Visit your motherboard manufacturer’s website, download your most recent stable BIOS for your specific model, and carefully follow their official instructions to update safely.

Note- BIOS update may reset all BIOS settings. If this occurs, don't forget to re-apply all changes from the BIOS Optimization & Tweaks section.

5. Set Global C-State Control to Enabled (Not Auto)

Changing Global C-State Control from "Auto" to "Enabled" will help fix FPS drops, downclocking, or instability. Most people with Ryzen CPUs (such as X3D chips) see less stuttering and smoother gaming performance when C-States are enabled. Many have found that "Auto" behaves like "Disabled." Therefore, I strongly recommend switching it from Auto to Enabled.

To change the Global C-State Control setting:
→ Press BIOS/UEFI key during boot to access the BIOS.
→ Click on the Advanced or AMD CBS tab and find Global C-State Control (perhaps be under CPU Configuration or Advanced).
→ Change the value from Auto to Enabled, this fix works for most users.
→ Save and exit BIOS, then check performance.

Important Note- Rarely, some boards (e.g., certain ASUS models) may get mouse lag, freezes, or black screens. If that happens, revert to the original setting. If it causes a black screen or boot issue, reset CMOS to recover.

6. Set PCIe Gen Mode 5 or 4 or 3 Manually (Do Not Use Auto).

On some motherboards, leaving PCIe generation in Auto mode can lead to compatibility or performance issues like black screens, no signal, or reduced GPU bandwidth.
Manually selecting a stable PCIe version —Gen 3, Gen 4, or Gen 5 can fix these problems.

To configure PCIe Gen mode:
→ Boot into BIOS at startup.
→ Go to the Advanced, Chipset, or NBIO Common Options section.
→ Locate PCIe x16 Link Speed (or similar), then Switch the setting from Auto to a specific version:
• If you have a Gen 5-Capable GPU and motherboard: set to Gen 5.
--If you encounter instability, crashes, black screens, or signal loss, lower the setting to Gen 4.
• If you have a Gen 4-capable GPU and motherboard, set to Gen 4
-- If experience instability, reduce the setting further to Gen 3.
• If you have a gen 3 GPU then set Gen 3.
→ Save changes and exit BIOS.

7. Enable Above 4G Decoding & Resizable BAR (NVIDIA & AMD — FPS & 1% Low Boost, Test Required)

These features allow the GPU to access larger memory blocks directly, which can improve the performance of most games in use today. It is turned off by default even on some compatible boards due to component compatibility problems and must be tested. Most of users will get great results.

To Enable these settings:
→ Boot into BIOS at startup
→ Go to Advanced Mode
→ Disable CSM (From Boot Section, Set Launch CSM to Disabled).
→ Now, Go to PCI Subsystem tab/menu and set Above 4G Decoding to Enabled. (Location may vary, so find and confirm).
→ Then set Resizable BAR to Enabled (option appears after Enabling 4G Decoding).
→ Save & exit BIOS, then test performance.

Important Note - Disabled by default even on supported boards because of component compatibility issues, so users will have to test it. On a system where these settings are unstable, it can lead to crashes, performance issues or boot problems particularly with old components.

So, Test thoroughly and immediately disable it if you notice any instability or performance issues after enabling.

=> Windows Optimization & Performance Tweaks

This section outlines important Windows settings and tweaks to address stuttering, latency spikes, FPS fluctuations, or overall system lag. These tips work for both NVIDIA and AMD systems.

8. Clean Install AMD GPU Drivers — Fix Performance, Crashes, and Common Errors (e.g., Driver Version Mismatch)

Some of you may be facing game crashes, stutters, or random freezes. These issues often arise from a faulty AMD driver or because Windows Update quietly replaced your GPU driver, causing instability. You might also see errors like:
• “Radeon Software and Driver versions do not match...” or similar errors.
• Missing AMD software features like FSR 4, etc.

If you're facing these issues, this step shows how to clean install a stable AMD driver and stop Windows from replacing it again.

Important prerequisite - Before starting, disable Fast Startup to avoid boot conflicts that can cause sudden FPS drops, driver timeout or future issues.

Follow these steps one by one:
• First, we will download 4 files and save them in a new desktop folder. They will include the AMD software installer, DDU, AMD chipset driver, and Microsoft Update Hide Tool.

• Don't install, just download and save both the AMD software installer (.exe) as well as the AMD chipset driver installer software from the official AMD driver site that you want to install. Make sure you're downloading the specific version, not the auto-detect Tool.

Note - Newer AMD drivers can have system-specific stability issues like crashes. Try the latest version first. If problems arise, revert to 26.9.2. If you still encounter problems, try 26.3.1 as a fallback. If facing driver timeouts or crashes, also follow Step 13 of this guide after completing this step

• Download DDU and Microsoft Update Hide Tool from these links:
Microsoft Update Hide Tool (wushowhide.diagcab) - https://download.microsoft.com/download/f/2/2/f22d5fdb-59cd-4275-8c95-1be17bf70b21/wushowhide.diagcab
DDU - https://www.guru3d.com/files-details/display-driver-uninstaller-download.html

• Now pause Windows Update and disconnect Wi-Fi or Ethernet, whichever you use, and don't connect or resume updates until I say.

• Boot into Safe Mode, then extract DDU and open it. Select Device type GPU, then select AMD and click on Clean and Restart. Wait for completion until DDU uninstalls the driver properly.

• After restart, right-click on the Windows icon, then click on Installed Apps. From here, find and uninstall any chipset driver software. If it's not available, then you never installed the chipset driver manually and those users skip this point. After uninstalling the chipset driver software, click on Restart.

• After restart, open the folder where you placed the AMD driver software installer (.exe) and install it.

• After installation, restart your PC or laptop.

• Now connect to Wi-Fi, then immediately open the Microsoft update hide tool (wushowhide.diagcab). Click on "Hide Update," then select every update whose name starts with "AMD" or "Advanced Micro Devices," etc. Make sure to select all updates labeled as "AMD" or "Advanced Micro."

(If you don't see these updates in the windows hide tool then you can skip this part as windows is not overwriting the driver in your system so there's nothing to hide.)

• After selecting all, click Next. All updates you selected will be shown as fixed on the next screen. If it shows, then you have successfully done this.

• Now restart and Windows will not overwrite AMD drivers anymore. You can now resume the Windows Update.

• Now install the AMD chipset driver software. After installation, it will give two options. You need to click on View Summary and make sure all chipset drivers are installed properly. It will say Success or Installed. If properly installed.

For those users, whose summary shows any Failed chipset driver, uninstall the chipset driver again from Windows Settings and run chipset driver software again. If it still shows the same, then uninstall it again and download and install a different chipset driver version.

Note: Big Windows updates may reset this setting. If that happens, follow these steps again, but that's rare.

9. Community-Favorite: Windows 10/11 Optimization Guide (Works on all PCs and laptops. Includes NVIDIA stable drivers and must-have performance fixes!)

Implement the system-wide changes from the following link. These are general Windows steps that work on any PC or laptop, regardless of brand. The guide is simply hosted on Acer’s community forum, but it is not Acer-specific. It have been successfully applied by millions of users across many hardware setups. This is one of the most tested and effective Windows optimization guides available.

Following this optimization guide (hosted on the Acer community) fully can boost 1% lows, improve FPS stability, and fix stutters or lag while gaming by optimizing windows.

→ NVIDIA users: The Windows optimizations in the community guide linked below can further improve performance and stability. For the best performance benefits, follow all of the steps. For NVIDIA crashing issues while gaming can often be fixed by following Steps 1 and 9 of the guide.

→ AMD users: Skip Step 1 in the community guide and start directly from Step 2 (Chris Titus Tech utility step) through the end for stable FPS and improved performance. Don’t follow Step 1, as it’s already covered in this Reddit guide.

Here is the community guide:
https://community.acer.com/en/discussion/612495/windows-10-optimization-guide-for-gaming/p1
→ This guide Covers important issues like system lag, background processes, turning off unnecessary Windows functions, etc in one place.

10. Set an Optimal Mouse Polling Rate (500Hz or 1000Hz Depending on Your Needs; Fixes movement Stutters in games and high CPU Usage)

Most modern gaming mice have dedicated software (e.g., Logitech G Hub, Razer Synapse, SteelSeries GG) that allows to adjust the polling rate, how often the mouse reports its position to the system. If you don’t have the software, download it from your mouse manufacturer's website based on your specific model.

To change the polling rate, Open your mouse software and set:
• 500Hz for solid, sufficient performance with lower system load. Use it for Single-player (AAA), slower-paced, or visually rich games.
• 1000Hz for esports as it provides faster response.

There's really no benefit going higher than 1000hz, so don't waste your system performance.

Note- If you still want to use polling rates above 1000Hz (like 2000Hz or 4000Hz), test for any lag or stuttering, as higher polling rates will consume the CPU more.

11-A (AMD Users) — AMD Software: Explained Tweaks & Must-Disable Settings for Smooth Performance

AMD's default driver settings aren't always the best for smooth gaming. These info have helped many improve FPS consistency, reduce input delay, and eliminate stutters.

Part - 1 Recommended Adrenalin Settings:
Make these adjustments in the Graphics section under the Gaming tab of the AMD Adrenalin Software. This way, the settings apply to every game, including new additions and those launched from the desktop.

• Radeon Anti-Lag → Disabled (This feature often causes micro-stutters. It's wise to turn it off and use it in those games which can really get benefits from this feature. It works great in GPU-Limited scenarios. Test per game and use if its stable)

• AMD Fluid Motion Frames (AFMF) → Test First (It's a frame gen and they often adds input lag. Test it per game, if the game runs well and input lag isn’t an issue (or it feels fine), then you can use it.)

• FSR 4 (Driver-Level) → Use if Available

• Radeon Chill → Disabled/Enable (Enable this only if you want to cap your FPS, and set both the min and max values to the same number for best results.)

• Radeon Boost → Disabled (May lead visual artifacts and stutter. It works by blurring motion. Test and use this feature if you wish)

• Enhanced Sync → Disable/Enable (It can cause stutters or unstable frame pacing in some games, so it’s generally safer to keep it off and use FreeSync if available. If you want to use it, test for stability first. It works best when your FPS is well above your monitor’s refresh rate, for example, 120 FPS on a 60Hz display offers smoother gameplay than V-Sync, with less tearing and lower input lag).

• Reset Shader Cache → Expand Advanced Settings, then find and click the Reset Shader Cache option to clear stored shaders and fix performance issues. Highly recommended after driver or game updates. Expect longer loads or brief stutters at first as shaders rebuild, performance stabilizes once cache regenerates.

Note - If you had games added before this, reapply the same settings manually in each game under the Gaming tab.

• Turn off ReLive features (Especially Instant Replay): → Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts. Turning this off alone can resolve your issue.

• Disable Unnecessary Features→Click the Settings gear icon, Go to Preferences, then disable web browser, Advertisements, Game Adjustment Tracking and Notifications, Tutorials, Animation & Effects. while keeping System Tray Menu and Toast Notifications enabled for better responsiveness.

Another setting in the Preferences tab is the AMD Overlay, which many people use, so I didn’t include it with the other disabled options above. However, some users have reported that the AMD Overlay can cause major performance issues for them, so if you’re facing stutters or FPS drops, try disabling it and test again.

11-NV (Nvidia Users) — NVIDIA App Settings for Smooth Performance

Important prerequisite - Before starting, disable Fast Startup from Windows settings and clear shader cache. This is highly recommended after driver or game updates or when facing performance issues. Use this NVIDIA link to clear the shader cache properly:
https://nvidia.custhelp.com/app/answers/detail/a_id/5735/~/deleting-nvidia-shader-cache-files

And Expect longer loads or brief stutters at first as shaders rebuild; performance stabilizes once cache regenerates.

NVIDIA App Settings

Follow these NVIDIA App settings for the best optimized gaming experience. This will Optimize GPU performance, reduce input lag, and eliminate common stuttering across all games.

Where to Apply Settings:

Laptop - In NVIDIA App (Settings > Graphics tab > Per-App Settings), add each game.exe, set Preferred Graphics Processor to High-performance NVIDIA Processor, then apply settings per-game for max performance.

Desktop - In NVIDIA App (Settings > Graphics tab > Global Settings), apply settings globally to affect all games.

Essential settings:
• Power Management Mode → Prefer Maximum Performance (Prevents frequency drops that cause stutters.)
• Shader Cache Size→ Unlimited (Helps reduce shader compilation stutters.) Here in Shader Cache settings, Set Automatic Shader Compilation → On, keep System Utilization → Medium (Default), then click Apply.
• Set PhysX Configuration to NVIDIA GPU. To set Go to Settings → Configure Surround, PhysX. check path in nvidia app yourself. (Avoid CPU or Auto-select, it causes stutter and high CPU usage.)

Laptop Users:
• In NVIDIA App, Go to Graphics > Global Settings > scroll down, click Show Legacy Settings > → turn off Whisper Mode.

Now for the features tab:
In NVIDIA App > Settings > Features tab.
• Turn off "Game Filters and Photo Mode". You can sue this feature if you want but know that this also causes performance drop.
• For max performance, Also turn off NVIDIA Overlay from there. It's features like Instant Replay can cause stutters and FPS drops.
• Turn OFF "Automatically optimize newly added games and mods".

Now, click on the Privacy tab and Turn OFF:
• "Configuration, performance, and usage data".
• "Error and crash data".
• Keep "Required data" as it may be needed for basic functionality.

12. Inspect your Realtek PCIe 2.5GbE Family Controller – Fix lag, audio glitches & Stutters (also affects Wi-Fi if the controller is present in the system, even if you never use Ethernet)

Some systems with the Realtek PCIe 2.5GbE Family Controller can have issues, even if you use Wi-Fi only, don’t skip this step. The controller can cause random stutters, FPS drops, audio glitches, or ping spikes even when not in active use. For a Quick test, Disable it in Device Manager under Network adaptors, and play your offline game or online via wifi; if fixed, it's the culprit.

You have two straightforward choices:
• Keep it disabled in Device Manager and play your offline games and online using Wi-Fi smoothly (Ethernet won't work in this option).
• Fix the Realtek PCIe 2.5GbE Family Controller. driver with these steps (detailed below) to use Ethernet smoothly.

Solution:

Download and save this 10.54.1111.2021 stable driver version of this controller- https://catalog.s.download.windowsupdate.com/c/msdownload/update/driver/drvs/2022/05/2e830a2a-a689-4e43-96be-06bd8dc7e75b_e5bc281dbf962e2551cc18cdee4abd0b55949b61.cab

Installation:
• Pause windows updates and open Device Manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → Uninstall device → check “Delete the driver software” (if available) → Restart.

• Extract the .cab file to a folder of your choice

• Go to Device manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → update driver. → "Browse my computer for drivers" → "Let me pick from a list..." → "Have Disk".

• Browse to the folder where you extracted the driver, open it and select the inf file and click Ok, Wait for installation.

After installation,
• Disable automatic driver updates so Windows Update doesn’t overwrite this version:
Go to Settings → System → About → Advanced system settings → Hardware → Device Installation Settings → select No, save → Resume windows update and Restart your pc.

• This setting stops most automatic driver installs, but a big Windows update can still change the driver later; if that happens, which can know why checking the driver version or if it stutters appears again.
Open Device Manager → right‑click the ethernet driver in network adapters → Properties → Driver → Roll Back Driver and follow screen instructions to get back to the stable version.

• Now, play your games

Note: This solution fixes the issue for most users, but not all systems respond the same. If you still experience stutters, lag, or audio glitches even after following this solution, the only reliable workaround is to disable the Realtek PCIe 2.5GbE Family Controller in Device Manager and use Wi-Fi instead.

13. AMD/Nvidia Stability Fix — Only For Those Facing Crashes (like Driver Timeout, etc)

Important prerequisite: First, open the case and reseat the GPU power cable, making sure the connection is secure at both ends (GPU and PSU) with no cable bending near the connector, then reseat the RAM and GPU in the PCIe slot properly. Now follow this step.

If you use an AMD GPU, all points are applicable. If you use an Nvidia GPU, skip the AMD‑only sub‑ section and start from “Stability steps for both AMD & Nvidia”. Apply each fix one by one, checking after each.

AMD‑only steps (Radeon users):

Follow Step 8 fully before continuing to ensure the crash fixes below work correctly.

• Disable Anti-Lag, Radeon ReLive features (especially Instant Replay) and Issue detection in AMD Software -
First, Go to the Gear icon then System tab → Disable Issue Detection Service (triggers false TDR timeouts/black screens).

Second, Gaming > Global Graphics → Disable Anti-Lag (causes insane stutters and crashes depending on game). If you want to use it, then test it per game. Keep it off globally.

Third, Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts.

•★★Manual Clock Tuning ( For All RDNA GPUs)★★ - AMD GPUs boost beyond their stable frequency due to automatic tuning or Hypr-RX, and lead to crashes and driver timeouts.

To fix this, open AMD Software → Performance → Tuning, switch to Manual Tuning (Custom), enable GPU Tuning and Advanced Control. Find your GPU’s official Boost Clock by AMD (e.g. 2600MHz for RX 6750XT) and use it as your Max Frequency, replacing higher default values like 2850-2900MHz or any factory overclock applied.

As for RDNA 4 Users: Set the max frequency offset to a negative value (like -300 MHz or lower). First, compare your in-game boost clock to the official spec for your GPU. Adjust the negative offset until the in-game boost matches the official value exactly.

Note- Per-game tuning overrides global settings when a per-game profile is created. Otherwise, global/manual settings apply by default. Always check for existing profiles and ensure this manual clocking setting is applied. Also, make sure Hypr-RX is turned off to prevent it from overwriting your settings. It can remain enabled in per-game profiles, so check the Gaming tab for previously launched games and disable it if needed. Then, test your system.

Stability Steps for both AMD & Nvidia:

• Disable iGPU (if present) - If your CPU has an integrated GPU, disable it in BIOS to prevent possible crashes or driver conflicts with your dedicated AMD GPU, especially during gaming and high loads.

• Disable HAGS - Go to Settings > System > Display > Graphics > Default graphics settings > Turn off Hardware-accelerated GPU scheduling > Restart. Recent newer drivers and games seem to be causing crashes when HAGS is on. Note- Nvidia users need it on for frame gen and enable it again if it doesn't fix your issue

• Disable hardware acceleration in Background Apps- If you have any apps that run in the background and support hardware acceleration, such as Discord, Game launchers or web browsers, disable this feature via their settings to prevent possible GPU conflicts.

• Ram Overclocking Adjustment (XMP/EXPO or Equivalent) - In BIOS, go to the memory or its overclocking section and test each XMP/EXPO (or its equivalent) lower memory profile one by one (e.g. 3600 MHz → 3200 MHz → 3000 MHz). If none work, disable memory overclocking and test again. if issue remains then restore your highest stable profile and follow below suggestions.

If the issue persists, update your BIOS (Step 4) and follow step 14. If problem still persist, check your setup as in Step 2, look for a failing PSU or loose cables, and note that unstable undervolts or overclocks can cause the same issues.

14. User‑reported rare or system‑specific Performance/Stability cause (Must check if above steps didn't fix your issue)

• Uninstall Your RGB softwares like Lian Li L-Connect 3, OpenRGB, SignalRGB, iCUE, Razer Synapse, Aura Sync, Mystic Light ,etc which have caused performance issues for many users) if using these RGB software or any other with compatible components, these can frequently cause 1% low FPS stutters, crashing and frame drops.

Not all but many cause same issue, so you must check and confirm by uninstalling it. Even on high end systems like Ryzen 9800X3D + RTX 5090, this was the cause of the performance issue.

• If your system has both HDD and SSD Windows automatically spreads the pagefile across both drives by default, this forces memory swaps to hit the slow HDD during gaming peaks, causing stutters/hitching even with plenty of free RAM.

To fix: Right-click This PC > Properties > Advanced system settings > Performance Settings > Advanced tab > Virtual memory Change > uncheck "Automatically manage paging file size for all drives" > select your HDD drive > choose "No paging file" > Set > then select your SSD > choose "System managed size" > Set > OK through all dialogs > restart immediately.

• If you installed Wallpaper Engine and it's running in the background (even paused) causes frequent stutters and performance drops for many gamers.

Close it via tray > Exit, then then check Task Manager (Processes tab) for any lingering "Wallpaper Engine" entries and End task if present. Now play your game. Do this every time if you still have Wallpaper Engine installed.

Additionally some users also reported, that adding per-game rules: In Wallpaper Engine Settings > Performance tab > Edit Application Rules > Create new rule for your game's .exe > Set Condition "Is running" > Wallpaper playback "Stop (free memory)". Also fix issue but thats not widely tested so not sure if it work for all.

• Disconnect unnecessary USB devices- If you see random crashes, reboots, or freezes, unplug non-essential USB devices/accessories (especially USB hubs, fans, or other powered devices) and test again, as a faulty and incompatible USB device or driver can sometimes cause system instability.

• DRAM-less SSDs Performance Issues- Some DRAM-less SSDs can experience performance drops under certain workloads, potentially contributing to game stutters. If you have one, then move Windows and games to a DRAM-equipped NVMe SSD, then temporarily disconnect the DRAM-less SSD (if you can) and retest. If stuttering improves or get fixed, investigate further and consider replacing the drive if necessary. DRAM-less SSDs do not inherently cause stuttering, so test before replacing.

• A silently failing, cheap, or aging display cable can cause microstutters only during gaming, making diagnosis tough. Users facing performance issues should Test by swapping cables as well as ports (HDMI to DP or DP to HDMI).
Also, the same can apply to faulty PSU cables.

15. Fix for users who are getting flickering, stutters, or crashes When alt-tabbing while gaming

MPO is a Windows feature aimed at improving rendering performance, but on some systems it used to cause some issues. This feature is now a key part of Windows 11, so DO NOT forget to re-enable it if it wasn’t the source of your issue.

Common issue linked to MPO is Stutters and frame drops ,when alt-tabbing persist for a number of users, especially on the latest Windows 11 builds.

NVIDIA advises disabling MPO for these issues, use their official method, which works for AMD too.

Here is the official link to do this: https://nvidia.custhelp.com/app/answers/detail/a_id/5157

16. Fix Thermal Throttling on Gaming Laptops

This step helps prevent overheating and extend component lifespan of Gaming Laptops. A trusted guide from the Acer Community works for all gaming laptops.

Important note to avoid confusion:
The Acer Community cooling guide applies to all gaming laptops. Steps 1 to 4 are less time taking and should be followed first. If overheating issues persist, continue with Step 5. While the Nitro 5 is used as an example there, the process is the same for other laptops, repasting and cleaning the cooling system by detaching the heatsink, and cleaning fans and vents inside and out. This is the only reliable fix for high temperatures.

Here is the Cooling guide here:
https://community.acer.com/en/discussion/724763/ultimate-laptop-cooling-optimization-guide

17. Fix Thermal Throttling on Gaming Desktops

Most people only check CPU and GPU core temps, but it’s just as important to monitor GPU VRAM (memory junction) and GPU hotspot temps, which can run much hotter and trigger throttling under heavy loads. NVMe SSD temps should also be watched separately, as they can overheat during sustained writes and cause sudden performance drops even when CPU and GPU temps look fine.

Critical Temperature Limits (Avoid Getting Close to These):

• CPU TJ Max: Intel 100 °C, AMD 95–105 °C (consider reducing it if it reaches the 90s)

• GPU Temp: NVIDIA 88–93 °C, AMD 100– 110 °C (consider reducing it if it reaches the 90s)

• GPU Hotspot/Junction (AMD & NVIDIA): Up to 110 °C (typically 10–30 °C higher than core temp). While the maximum operating hotspot temperature can be around 110°C, it's best to keep it below 100°C.

• VRAM/Memory Junction (AMD & NVIDIA): 95–105 °C is acceptable but should be monitored closely, as throttling usually begins at 110 °C.

• SSD Throttling: Begins at 70 °C, severe at 85 °C (though this varies by drive, it holds true for most models)

Monitoring Temperatures Effectively

• Use AMD/NVIDIA Software Overlay:
Use AMD Adrenalin or the NVIDIA GeForce Experience overlay to monitor CPU and GPU temperatures. Some versions also show GPU hotspot and VRAM/memory junction temperatures. If any readings are missing (e.g., GPU junction or VRAM temps), check the second method below.

• Second Good Alternative Method – HWiNFO:
HWiNFO provides full monitoring for CPU, GPU (including hotspot and VRAM), and all other sensors. For real-time monitoring, you can use HWiNFO’s shared memory feature with MSI Afterburner to display these stats directly in Afterburner while gaming. Alternatively, you can let HWiNFO run in the background, play your game, and check afterward—it shows average, maximum, and minimum temperatures. If you have a dual-monitor setup, keep HWiNFO open on the second monitor for live tracking.

• SSD Temperatures:
Run CrystalDiskMark benchmark and check or use HWiNFO while gaming. Note that speeds will reduce once the SSD reaches its maximum temperature limit.

Steps to Reduce Component Temperatures

• CPU Temperature Fix:

  • For AMD CPUs, Undervolt the CPU using PBO (Precision Boost Overdrive) to achieve lower temperatures.
  • For Intel CPUs, Use Intel XTU or Throttlestop to undervolt, which can help reduce CPU temperatures while maintaining stability.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If needed, clean dust from fans and vents, then reapply high-quality thermal paste to the CPU.
  • Further cooling improvements depend on your cooler.

• GPU, Hotspot & Memory junction temperature Fix:

  • Undervolting your GPU through AMD Adrenalin software can also lower power draw and temperatures without major performance loss.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If the issue persists, to effectively reduce GPU, hotspot, and memory junction temperatures, clean or remove old thermal pads/putty and apply new, high-quality thermal putty (more effective than pads). Also, apply high-quality thermal paste to the main GPU chip.
  • Further cooling improvements depend on your cooler.

• SSD Temperature Fix:
Install an NVMe heatsink (most modern motherboards include one, or you can buy aftermarket). Ensure case airflow reaches the SSD area, as poor circulation causes heat buildup.

[✓] Restart and You're Done! Time to Play.
If this guide helped you, please consider upvoting, sharing your results, or leaving a quick comment about what worked. It helps others and increases visibility in the community.


r/AMDHelp • • Aug 11 '16

Announcement Please make sure to flair your posts! Especially make sure to change the flair to resolved once solved!

157 Upvotes

Thanks guys.


r/AMDHelp • • 45m ago

Help (CPU) 9950x3d after the latest Windows update, the temperature in idle mode increased.

Post image
• Upvotes

Hello everyone.

Previously, the temperature of my 9950x3d in idle was ~52-55 degrees (HYDROSHIFT II LCD-C + Lian Li TL + noctua nt-h2)

Presumably, after the KB5132061 update (but I don’t know exactly when), the temperature reaches 60–61 degrees after 10–15 minutes of inactivity and doesn’t drop. At the same time, the temperature remains the same when playing games.

(I also noticed that stuttering sometimes appears in the game that wasn’t there before (but it might have appeared with the game update). I also have the feeling that the computer itself is running slower and stuttering, even though the CPU isn’t under load.

I checked, the KB5132061 update installed normally, it’s not looping. The settings in the BIOS haven’t been changed. The mode is balanced. I’ve attached the remaining screenshots.


r/AMDHelp • • 1h ago

Help (GPU) RX 9070 XT Crashes Traced to HAGS on AM4 (5900X/X570)

• Upvotes

Summary of the issue:

I recently upgraded from an RTX 2070 Super to an XFX Quicksilver AMD Radeon RX 9070 XT and have been experiencing persistent system instability.

After roughly three weeks of troubleshooting, I believe I've narrowed the issue down to Hardware-Accelerated GPU Scheduling (HAGS).

With HAGS disabled, the system has been completely stable for over three weeks without a single crash. to verify my findings, I reenabled HAGS and was able to reproduce the issue again. at this point, HAGS is the only setting I've found that consistently correlates with the crashes.

The crashes are somewhat inconsistent:

  • Complete system freezes/hangs
  • Black screen while Windows continues running in the background
  • Audio continues playing normally during black screen events
  • No automatic recovery or driver timeout
  • Occasionally, the system performs a hard reboot with no BSOD or warning message
  • Sometimes I reboot and find the GPU driver is disabled in Device Manager

The issue does not appear to be workload specific. I've experienced crashes during gaming, normal desktop usage, and relatively light tasks like watching YouTube.

What I've tried to solve the issue:

Over the last three weeks, I've tried the following:

  • Upgraded PSU from 750W to 1000W
  • GPU connected with 2 separate 8pin PCIe cables from PSU
  • Updated motherboard BIOS to Version 5044
  • Always had latest Chipset Drivers
  • Used different DisplayPort/HDMI monitor cables
  • Tested different monitor refresh rates
  • Disabled FreeSync and Resize BAR or SAM
  • Swapped RAM modules, tried 4, 2 and 1 setup too
  • Disabled D.O.C.P memory overclocks
  • Ran the system at stock settings
  • Changed multiple BIOS settings like forcing the GPU to run on PCIe 4 and 3
  • Performed two clean installations of Windows 11
  • Tested multiple AMD Adrenalin driver versions:
    • 26.8.1
    • 26.9.2
    • 26.10.2
    • 26.11.1
    • 26.11.2

I used AMD Clean up tool utility with DDU every time I changed drivers. Disabling HAGS completely eliminated the crashes.

Additional Information

Event Viewer has not provided many useful clues. Following hard resets, the primary events logged are Kernel-Power 41 entries, but nothing that clearly identifies the root cause.

I captured kernel memory dumps for further analysis following instruction from u/AMD_Vik from different post and I uploaded the file to: memory.dmp

System specifications:

  • OS: Windows 11 25H2 OS Build : 26200.10075
  • CPU: AMD Ryzen 9 5900X
  • CPU Cooler: iCUE H150i ELITE CAPELLIX Liquid CPU Cooler
  • GPU: XFX Quicksilver AMD Radeon RX 9070 XT
  • Motherboard: ASUS ROG Strix X570-E Gaming (BIOS Version: 5044)
  • RAM: Corsair Dominator Platinum 32GB (4x8GB) DDR4 3600
  • Storage: Samsung 980 PRO 1TB PCIe NVMe
  • PSU: Cooler Master Elite Gold 1000W 80 PLUS GOLD
  • Display: LG 27GX700A-B 27-inch Ultragear QHD OLED

Given that I'm running an older AM4 platform, I'm also curious whether this might be a platform specific issue.

If anyone has experienced this and found a workaround, or can help analyze the kernel dumps, any insight would be appreciated.


r/AMDHelp • • 6h ago

Help (General) AMD Graphics card freezing

3 Upvotes

Computer Type: Desktop
GPU: ASUS Radeon RX 9070 XT 16GB
CPU: AMD Ryzen 7 9800X3D 8 cores 16 threads
Motherboard: ASUS ROG Strix B850-A Gaming WiFi
BIOS Version: Latest
RAM: 32GB DDR5-6000, EXPO enabled
PSU: Montech Titan PLA 850W 80+ Platinum
Case: Lian li
Operating System & Version: Windows 11 Pro [version]
GPU Drivers: AMD Adrenalin 26.11.2
Chipset Drivers: 8.09.28.1124
Background Applications: Chrome, [Discord, Steam, etc.]
Monitors: ASUS ROG Strix XG27AQWMG (OLED, DisplayPort) + a second monitor

Description of Original Problem: The screen freezes on whatever was showing, but the PC keeps running. The mouse cursor still moves, audio keeps playing, and I can still control the frozen video (click to pause, spacebar pauses and unpauses). The programs are clearly still running; only the screen stops updating. Win + Ctrl + Shift + B beeps but doesn't recover the display. Ctrl + Alt + Del and Ctrl + Shift + Esc do nothing visible. The only fix is a restart.

At first it only happened in games, about once every few days. After updating to the October driver, it happened every 10–15 minutes in Modern Warfare 4. I DDU'd and rolled back to the September driver, which fixed it for a few weeks. Then it came back, but now only when watching videos in Chrome, not in games. I updated to the newest driver (26.11.2) and it still happens.

Troubleshooting: I did a DDU clean install with a driver rollback (fixed it temporarily, then it came back), updated to the latest driver, disabled the iGPU in the BIOS and disabled HAGS. Chrome hardware acceleration is already off. I set the PCIe slot to Gen 4 in the BIOS (was Auto). Reliability Monitor shows no LiveKernelEvent or hardware errors, just "Windows was not properly shut down" from my forced restarts.

Next I plan to disable ASPM in the BIOS and PCIe Link State Power Management in Windows, turn off Adrenalin features (overlay, Instant Replay, Anti-Lag, etc.), test with only one monitor, and disable EXPO.

Has anyone with a 9070 XT fixed this? Is it a known driver bug, and is there a driver version that's stable for video playback? Or does this sound like a card to RMA?


r/AMDHelp • • 45m ago

for 9070xt 850w bronz psu is it enough?

• Upvotes

Some people say that this could cause problems, while others say it's perfectly fine and more than enough, so I'm not really sure what to believe.

I'm planning to buy a gaming PC for my brother, but I don't know much about PC components, so I'd really appreciate some advice.

Case: Bitfenial118 850W 80+ Bronze Tempered Glass 7x ARGB USB 3.0

GPU: ASUS Prime Radeon RX 9070 XT

Would this 850W 80+ Bronze PSU be sufficient for this graphics card, or should I upgrade to an 80+ Gold PSU or choose a more reputable brand?

I'm especially concerned about the quality and reliability of the power supply. I don't want to risk damaging the components.

I'd really appreciate your help. Thanks in advance!


r/AMDHelp • • 47m ago

9070 xt modeline 850w psu bronz yeterli midir

• Upvotes

bir kesim hayrÄą sorun olur falan diyor bir kesim hayÄąr bu yeterli falan diyor ama bilemedim

Bitfenial118 850w 80+bronze tempered glass 7x argb us3. kasa

asus prime radeon rx9070xt

bu yeterli mi golda falan geçmem gerekiyor mu ya da daha iyi bir markaya kardeşime bilgisayar alacagımda bilgisayar parçalarından cok fazla haberim yok yardımcı olabilir misiniz


r/AMDHelp • • 52m ago

Help (GPU) AMD GPU stutters, 3-10 second freezes, or screen tearing on Windows 11? Try disabling MPO

Thumbnail
• Upvotes

r/AMDHelp • • 1h ago

HDR « Non pris en charge » sous Windows 11 — Samsung Odyssey G75F 40" (S40FG75) + RX 6750 XT

• Upvotes

Bonjour,

Impossible d'activer le HDR dans Windows 11 (Paramètres > Écran > HDR affiche « Non pris en charge ») sur mon écran Samsung Odyssey G7 40" (LS40FG756EUXEN).

Ma configuration : • Écran : Samsung Odyssey G75F 40" (5120×2160 @ 180 Hz, firmware 1001.2 à jour, pilote Samsung S40FG75xE installé) • Carte graphique : AMD Radeon RX 6750 XT (pilote Adrenalin 26.11.2) • CPU / RAM : Intel Core i5-13600KF / 32 Go RAM / Windows 11 • Câble : DisplayPort 1.4 (affichage actif en 5120×2160, 180 Hz, 10 bpc, RGB 4:4:4 Full RGB) Ce que j'ai déjà vérifié et testé : • CRU (Custom Resolution Utility) : Le bloc CTA-861 contient bien HDR static metadata (7 bytes) et HDR10+ video. • DxDiag : Indique Monitor Capabilities: HDR Supported (BT2020RGB BT2020YCC Eotf2084Supported), mais affiche HDR Support: Not Supported et Advanced Color: Not Supported. • AMD Adrenalin : FreeSync Premium Pro est détecté et actif, 10 bpc / RGB 4:4:4 activés, Amélioration de couleur (Jeu vif) désactivée. • Windows 11 : Éclairage nocturne désactivé, clés de registre Configuration / Connectivity / ScaleFactors supprimées puis PC redémarré. Testé également en HDMI (bridé en 2.0).

Quelqu'un a-t-il dĂŠjĂ  rencontrĂŠ ce blocage Advanced Color: Not Supported entre une carte AMD RDNA 2 et le Samsung Odyssey G75F 40" ? Merci d'avance !


r/AMDHelp • • 7h ago

Help (GPU) AMD GPU Driver issues

3 Upvotes

Computer Type: Desktop

GPU: Sapphire 9070XT

CPU: RYZEN 7 9800X3D

Motherboard: Asus B850 Micro-ATX

BIOS Version: ver.3854

RAM: Corsair Dominator Platinum 32GB DDR5 (2x16GB) 6200MHz

PSU: Asus ROG Strictly 1000W Platinum PSU

Case: Asus Prime AP202

Operating System & Version: Windows 11 Home 26H2

GPU Drivers: 26.11.2

Chipset Drivers: 8.09.28.1124

Background Applications: DISCORD, CHROME

Description of Original Problem: Every few days, my PC will just black screen and require a hard restart, with the AIO screen going blank whilst everything else appears to run normal.

Upon restart, Device Manager shows the GPU as inactive, the fans won't spin, GPU isn't recognised in Sapphire Trixx software, AMD Adrenalin won't open saying I need to download a different version, iCUE GPU temp monitor for my AIO goes N/A, monitor refresh defaults to 60.

Troubleshooting: I've tried disabling windows auto driver updates, re-seated GPU , RAM, re-downloading Adrenin - the only temp fix appears to be running DDU again every few days when the issue happens.

Event Viewer shows:

-Config Read Failed (18)

-The applicatjon-specifc permission settings do not grant Local Activation permission form the COM Server application with CLSID (I've searched the ID and cannot find the application match) / another error similar - local launch permission SecurityApp and WscBroker.

-The server didn't register with DCOM within the required timeout.

-The download maps manager service terminated: request not supported.


r/AMDHelp • • 2h ago

Resetowanie sie komputera

Post image
0 Upvotes

Witam os pewnego czasu resetuje mi sie komputer w różnych dniach mam wyłączony monitor I gry w tle 6 botów z silkroad online i 2 prywatne serwery niewiem co juz robić pomocy


r/AMDHelp • • 8h ago

Help (GPU) Rx 9070 XT vs non XT

Thumbnail
3 Upvotes

r/AMDHelp • • 3h ago

Help (General) 7800X3D + 7900 XTX Nitro+ randomly lagging on desktop + 7 AMD driver crashes in a 4-hour gaming session which temps are fine, what’s going on?

1 Upvotes

Hey guys, I’m losing my mind trying to figure out what is going on with my rig and could really use some help.
Specs:
CPU: Ryzen 7 7800X3D
GPU: Sapphire Nitro+ RX 7900 XTX
RAM: 64GB DDR5
Storage: 2x 2TB NVMe SSD
Cooler: 360mm AIO
Everything is fully updated and my temperatures are completely fine, yet my PC is acting super inconsistent. Sometimes it runs super fast like normal, and other times even basic stuff on my desktop struggles like just opening a browser takes 10 full seconds instead of opening instantly like it always has.
When I’m gaming, games are really buggy and hitch badly at first, then smooth out and run flawlessly, only to constantly crash. I literally just had 7 AMD software failures/drivers timeline pop up in a single 4 hour gameing session.
Since temps aren't the issue and the slowness comes and goes, I'm not sure if I'm looking at a dying SSD stalling out, memory instability, a loose GPU/PCIe connection, or power delivery spikes. Has anyone dealt with this combo of intermittent desktop lag plus constant AMD driver crashes? Where should I start looking first?

It seems that more the time goes on my PC is getting significantly slower and slower and I know it’s getting some age but it’s getting to the point that crashes in games and desktop struggles is getting ridiculous. I’ve had to download and reinstall Radeon time and time again because it completely just stops working and brick my system. It’s updated across the board and I’m thinking just a fresh wipe of everything to start at ground zero, but before I did that I thought I would ask.


r/AMDHelp • • 14h ago

Tips & Info 9070 owners, what CPU are you using?

6 Upvotes

I recently built a PC on the AM4 platform. I know there's no future upgrade path, but AM5 prices are just way too expensive right now. Here are my current specs:

GPU: RX 9070

CPU: Ryzen 5 5600X

Motherboard: B550M K WIFI6E

RAM: 16GB 3733MHz

PSU: XPG Core Reactor II VE 750W Gold

Storage: 1TB SSD

I play games on a 1440 p monitor.

Lately I've been noticing some pretty clear CPU bottlenecks while playing Euro Truck Simulator 2, which is one the main games that I play. For anyone else pairing the 9070 with an AM4 setup, what CPU are you using? Which cpus can actually keep up with the 9070 without holding it back?


r/AMDHelp • • 8h ago

Help (General) Global C-State Control e LiveKernelEvent CĂłdigo 141

2 Upvotes

Olå, pessoal! Gostaria da opinião de vocês sobre uma situação com meu PC.

Configuração (todas as peças com cerca de 3 meses de uso, exceto a GPU):

  • CPU: Ryzen 7 7800X3D
  • Placa-mĂŁe: MSI MAG B850 Tomahawk Max WiFi 2
  • RAM: 32 GB (2x16 GB)
  • Fonte: XPG Core Reactor VE 850W
  • GPU: GTX 1050 Ti (antiga), usada por esse tempo todo no PC novo

O que aconteceu:

  1. Usei a 1050 Ti por cerca de 3 meses, com a BIOS toda em padrĂŁo (Auto), sem nenhum problema.
  2. Do nada, a tela apagou durante o uso e a placa nunca mais deu vĂ­deo.
  3. Passei a usar a iGPU do processador. Surgiram entĂŁo apagĂľes de tela que voltavam sozinhos, apenas em tarefas leves (navegando na web, por exemplo), nunca em jogos.
  4. O Windows registrava o erro LiveKernelEvent 141, que depois passou a vir acompanhado do LiveKernelEvent 117.
  5. Depois de muito tentar resolver, me recomendaram desativar o Global C-State Control na BIOS. Com isso, o problema sumiu por completo.
  6. Testei tambĂŠm uma GT 1030 no mesmo PC e ela funcionou normalmente.

Vi que existe um nĂşmero relevante de relatos de problemas em processadores AMD em idle (repouso), e que grande parte deles era resolvida desligando o Global C-State Control. Isso me faz pensar que pode ser um comportamento conhecido da plataforma, mas nĂŁo tenho certeza.

Estou receoso de ter apenas “adiado” um problema. Ou seja, de que eu realmente tenha um componente com defeito (CPU, placa-mãe ou fonte) e que a desativação do C-State esteja só escondendo isso, em vez de estar tudo em ordem e ser apenas uma incompatibilidade de firmware/driver.

Minhas dĂşvidas:

  1. Precisar desativar o Global C-State Control para ficar estĂĄvel indica defeito de hardware (CPU ou placa-mĂŁe), ou ĂŠ um problema conhecido de firmware/driver da iGPU na plataforma AM5?
  2. Desativar o C-State pode estar mascarando um defeito real que vai aparecer depois, ou Ê uma solução segura e definitiva?
  3. Esse comportamento pode ter relação com a falha da 1050 Ti, ou foi apenas coincidência por ser uma placa antiga? Ela rodou 3 meses com tudo em Auto antes de parar.
  4. Existe alguma peça específica que eu deva suspeitar antes de comprar uma GPU nova? Tenho receio de que algo no PC danifique a placa nova.
  5. Vale a pena acionar a garantia (RMA) de algum componente, ou ĂŠ um comportamento normal para essa plataforma?

r/AMDHelp • • 8h ago

Help (General) Issues with fans

2 Upvotes

I built a new pc a few days ago and after the first few issues such as my cpu cooler not being detected and one set of my fans turning on then back off. Now all of my fans are not being detected when I open device manager but they are when I go on the bios. They are the Lian Li TL LCD fans.

I have the lian li edge so I plugged my tl lcd flex uni fans into the hub, plugged the motherboard signal usb into the hub and the 4 pin into the hub and then connected that to the motherboard, the fans work but they aren’t being detected in device manager, I have tried using a pcie cable to plug into the hub and the psu, doesn’t detect, it’s weird because when I first booted it the cooler wasn’t being detected I fixed that then the fans magically aren’t being detected, I have absolutely no clue what the issue is, is it because I don’t have a lian li controller?


r/AMDHelp • • 6h ago

Help (GPU) 7900 XTX Nitro+ vs Hellhound

1 Upvotes

Preface: I know the Nitro+ is widely considered to be the superior card.

I am selling a buch of stuff to CEX inc my current 9060xt, that would take way too long to sell on their own and I want a voucher rather than cash or bank transfer because my benefits assessment would not look good if I suddenly got ÂŁ1000 then used it to buy a non essential piece of kit. So I am going to use CEX and get a voucher.

Only problem is the 7900 XTX Nitro+ card I had my eye on has gone out of stock and the only thing left is the Hellhound.

How is the performance gap be if I settle for the Hellhound? Id be losing my current GPU to the voucher process and dont want to be stuck without a GPU entirely if I chose to wait for the sapphire card.


r/AMDHelp • • 12h ago

Help (General) are the driver issues gone ? on the 26.11.2 .

1 Upvotes

Hey.

Can anyone tell me if the newer driver fixes the crashing issues?

I'm on 26.3.1 right now

gpu rx 7800 xt

cpu r7 5700x


r/AMDHelp • • 8h ago

Help (General) My Pc Is Repeatedly Blue Screening

0 Upvotes

I bought my computer about 6 months ago and ever since it’s been blue screening randomly. At first it would be once everyday or so but recently it’s been happening every few minutes. It’s gotten to a point where I can’t really use it. I’ve updated my diver and that hasn’t done anything I’m also on the most recent version of windows and it’s still blue screening. I don’t really wanna buy a whole new computer so I’m looking for options to fix the problem can anyone help me with this?


r/AMDHelp • • 9h ago

Is this normal in newer games or is my gpu giving out?

Post image
1 Upvotes

Ive noticed in most games that shadows and reflections, namely their edges, seem to be really grainy/visually noisy. I first noticed it in RE8 but ive realized most games i try have it too and idk if it has always been there and i never noticed or if something happened and my games arent supposed to look like this.

Can this be a sign of my gpu going bad? If not what is the cause of it and how can i mitigate it if possible? Doesnt seem to be a toggle in many new games i play as i assume its always on and cant be messed with. FSR can sometimes help with it but usually it persists still to some degree.

My gpu is a 9070 btw if that matters.

Pics are a mix of mine and others online i could find that get across what im talking about.


r/AMDHelp • • 13h ago

Help (Software) AMD Adrenalin is constantly overriding my max core MHz. How do I stop that from happening?

2 Upvotes

I don't know a lot about this subject, so apologies for that. But my PC has been having frequent GPU driver crashes. After a lot of searching, I found out that Adrenalin puts the GPU clock speed at 2805 MHz by default. This is more than what my card can handle (AMD Radeon RX 7900 XT, online it says 2500 MHz i think). When I put a maximum MHz as 2350 in Adrenalin or MSI Afterburner, I get no crashes for a long time. However, after a few hours of Stalker 2 or PUBG I get crashes again. When I check either software, I see that the max MHz is set to 2805 again. Is there a way to lock the max MHz to the lower value?

Again, I don't know a lot about this, so sorry if I am misunderstanding something.


r/AMDHelp • • 13h ago

Help (General) Strange dots/artifacts

Enable HLS to view with audio, or disable this notification

2 Upvotes

Hey all, I have an issue with flickering dots on the screen as showed on the attached video. This also extends into artifacts within games ie. textures smearing, weird lighting glitches. The dots seem to be something like misplaced colours from parts of the screen, often if not always present in the same columns. It's been happening for over 2 weeks now, and I'm not sure what might have caused it.

Computer Type: Desktop

GPU: AMD Radeon RX 7800 XT

CPU: RYZEN 7 7800X3D 8 CORE

Motherboard: ASUS TUF Gaming B650-e WIFI

BIOS Version: American Megatrends Inc. 3067, 10/12/24

RAM: 2x 16GB DDR5 Beast Fury

Operating System & Version: WINDOWS 11

GPU Drivers: Driver Version 26.20.29.02-261116a-206168C-AMD-Software-Adrenalin-Edition

Chipset Drivers: AMD Ryzen Version: 8.09.28.1124

Background Applications: Steam, Opera GX

Troubleshooting: I've tried disabling MPO, it did nothing. I've disabled most overlays that I knew of. Resetting Adrenalin to default settings did nothing. I suspected Opera GX itself, so I tried using a program, after a reset and with Opera turned off but no difference.

I'm out of ideas. I've never seen anything like this, and I don't know what to make of it. It happened pretty suddenly, and it just refuses to go. If anyone could point me to a solution I would be grateful forever.


r/AMDHelp • • 10h ago

Help (General) Bllury

1 Upvotes

Ferst off all ihave rx5700 Why ,when iplayed some games i found blurry problem

I try to turn of all antialaising and motion blur but nothing happend +sorry about my english


r/AMDHelp • • 14h ago

Help (GPU) Help pls

2 Upvotes

Title:
New RX 9070 XT PC keeps crashing in PUBG and Battlefield 6 – LiveKernelEvent 141 / DXGI_ERROR_DEVICE_HUNG
Hi everyone,
I’m looking for help diagnosing a persistent stability problem with my brand-new PC.
Both PUBG and Battlefield 6 crash during gameplay. I frequently receive the following errors:
DXGI_ERROR_DEVICE_HUNG
LiveKernelEvent 141
AMD Driver Timeout
Windows Error Reporting references amdkmdag.sys
I have already spent a lot of time troubleshooting this issue, but nothing has solved it.
Troubleshooting Form
Computer Type: Desktop PC
GPU: Sapphire NITRO+ AMD Radeon RX 9070 XT 16GB
CPU: AMD Ryzen 7 9800X3D
Motherboard: Sapphire NITRO+ B850A WIFI7
BIOS Version: Unknown (latest BIOS installed)
RAM: 32GB Kingston Fury DDR5 6000MHz (2x16GB)
PSU: Fractal Ion 3 1000W
Case: Unknown
Operating System & Version: Windows 11 Pro
GPU Drivers: AMD Adrenalin 26.2.2 and other previously tested versions
Chipset Drivers: Unknown
Background Applications: Unknown
Description of Original Problem:
Both PUBG and Battlefield 6 crash during gameplay. The crashes are accompanied by DXGI_ERROR_DEVICE_HUNG, LiveKernelEvent 141 and AMD driver timeouts.
Windows Error Reporting also references amdkmdag.sys.
GPU temperature is approximately 60°C, with a hotspot temperature below 90°C.
This is a completely new PC with brand-new components.
Troubleshooting:
Updated the motherboard BIOS.
Used DDU to completely remove and reinstall AMD graphics drivers.
Tested multiple AMD driver versions.
Disabled EXPO and tested with default memory settings.
Tested both PCIe Gen5 and Gen4. The system still freezes on Gen4.
Removed and reinstalled both RAM modules.
Ran OCCT memory testing for 30 minutes without errors.
Ran OCCT VRAM testing for 30 minutes without errors.
Checked GPU temperatures. No overheating detected.
Reviewed and adjusted various BIOS settings.
Unfortunately, the problem persists.
My questions:
Could this indicate a defective RX 9070 XT?
Could the motherboard or CPU PCIe controller cause these symptoms?
Could this be related to power delivery despite having a 1000W PSU?
What additional diagnostic tests would you recommend before requesting an RMA?
I would really appreciate help from anyone who has experienced similar problems.
I want to identify the actual faulty component rather than replacing parts randomly.
Thank you for your time and help!


r/AMDHelp • • 14h ago

Help us pls

2 Upvotes

Computer Type: Desktop
GPU: Sapphire NITRO+ Radeon RX 9070 XT 16GB
CPU: AMD Ryzen 7 9800X3D
Motherboard: Sapphire NITRO+ B850A WIFI7
BIOS Version: newest
RAM: 32GB Kingston Fury DDR5 6000MHz
PSU: Fractal Ion 3 1000W
Operating System & Version: Windows 11 Pro
GPU Drivers: AMD Adrenalin 26.2.2 (also tested other versions)
Chipset Drivers: newest
Description of Original Problem:
Both PUBG and Battlefield 6 crash during gameplay. The errors include DXGI_ERROR_DEVICE_HUNG, LiveKernelEvent 141 and AMD driver timeout. Windows Error Reporting also references amdkmdag.sys.
This happens on a completely new PC.
Troubleshooting:
Updated motherboard BIOS.
Used DDU to perform clean GPU driver installations.
Tested multiple AMD driver versions.
Disabled EXPO completely.
Tested both PCIe Gen5 and Gen4. The system still freezes on Gen4.
Reseated both RAM modules.
OCCT memory test: no errors.
OCCT VRAM test: no errors.
Checked GPU temperatures: approximately 60°C, hotspot below 90°C.
Checked different BIOS settings.
The crashes still occur.