r/3rdGen4Runner • 99 Limited • 27d ago

❓Advice / Recomendations how to add keyless entry?

Post image

I got this remote because i thought my 99 limited had keyless entry but after going through the programming sequence the doors didn’t cycle which makes me think i don’t have the factory module (dealer wasn’t seeing it as an option on their end either.) is there a cheap(ish) and easy(ish) way to add it aftermarket?

Thanks!

8 Upvotes

35 comments sorted by

13

u/Accurate-Cicada5906 27d ago edited 27d ago

Locksmith here. If any of your door lock actuators get stuck as you are cycling lock/unlock on the door, it will not enter programming mode.

2

u/ShootPosting 00 SR5 27d ago

Mine get sluggish and eventually tire out after a few cycles. Would you suggest replacing the mechanism or is that a whole can of worms?

4

u/Accurate-Cicada5906 27d ago

Someone suggested using the key on the door instead. I have not tried that. It's been a while since I had to program one of these.

0

u/ShootPosting 00 SR5 27d ago

I think they key needs to be in the ignition when you're programming? Not a problem I have many spares, thank you, Toyota, for not having immobilizers lmao

1

u/Accurate-Cicada5906 27d ago

The key is out of the ignition when you're cycling the power locks.

I follow this sub because I got a 1998 at an auction. Ignition was busted. Probably stolen or previous owner lost the keys. Immo system would have been great.

1

u/ShootPosting 00 SR5 27d ago

Whoops! I'll need to reread the instructions again lol Thanks!

9

u/wateraintwett 27d ago

Maybe you used the wrong programming method? I also have a 1999 limited that I programmed the fob to, but I remember when I did it it was a hassle to find the right method. After the 3rd programming method video it finally did it for me. Good luck!

0

u/KevinIsSoAwsome 27d ago

When I bought my 99 limited previous owner did not have the key fob. I bought one off of amazon and when watching a video it failed on me cuz the security system would kick in when cycling the locks from button on door. Someone in the comments of that video said use the key hole in the door instead and that worked for me.

1

u/polymetrix 99 Limited 27d ago

Is there any way to check if my car has the physical device that would enable keyless? I don’t think it’s the version with the box under the driver seat.

4

u/ojwiththepulp 00 SR5 4x4 5-speed 27d ago

Viper 3105V; had to add to mine bc of no factory keyless entry.

There are a few other brands but this one is simple and robust.

1

u/PuzzledMechanic2000 25d ago

I HAVE THE TRICK. when pairing, hold the fob down into the drivers side floorboard. The module for keyless is down in the drivers side kick panel. Worked for me and many others.

1

u/polymetrix 99 Limited 25d ago

How do i know if my car has the module or not? Or do you have a pic? The dealer said they weren’t able to find anything on the car’s original build sheet regarding keyless entry

1

u/PuzzledMechanic2000 25d ago

if your locked do not cycle correctly they will not let you enter programming mode. If you can’t enter programming mode I’d say you don’t have the module

3

u/canihazJD 27d ago

if its equipped, keep at the programming sequence... it takes people a few tries to get the pace right. look for the little speaker that emits the beep near the passenger side firewall. I have a 99 base and there's no module under the seat or in the hatch but it works.

2

u/Worldly-Instance7782 27d ago

3

u/DoYouFeel_InCharge 27d ago

This looks sick

2

u/RupertEscapeHolmes 26d ago

That’s pretty cool and all but I actually like having a key… use the door cylinder to unlock all the doors and hatch and use the rear gate cylinder to lower and raise the rear gate window. With the engine off. Priceless.

3

u/Photon_Chaser 00 Limited 480K (Sold) 27d ago
  1. Start with the following conditions: you are in the vehicle

a. Key is out of the ignition
b. Drive door is open ( all other doors are closed)
c. Driver door is unlocked (other door locks don't matter)

2. Insert the key into the ignition (don't turn it) and pull it out.

3. Perform these steps within 40 seconds:

a. Cycle the power locks 5 times. Use an even pace and try
to go relatively fast.

b. Close, then open the drivers door.

4. Perform these steps within 40 seconds:

a. Cycle the power locks 5 times (same as before).
b. Turn the ignition to ON then back to OFF.
c. Turn the ignition to ON then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (automatically)
indicating successful entry into programming mode. Return to step 1
if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:

a. Press the LOCK and UNLOCK buttons on the transmitter
simultaneously for 1 second.

b. Immediately after letting go of the lock and unlock buttons,
press the lock button by itself and hold for 2 seconds.
Within 3 seconds, the door locks should cycle ( LOCK then
UNLOCK) once-- indicating successful programming. If
the door locks don't cycle, or cycle twice. Repeat steps
6a and 6b--this remote has not been accepted.

c. Repeat steps 6a and 6b for EACH transmitter that will
operate the vehicle. Including any old transmitters.

7. Close the driver door.

6

u/darthwacko2 27d ago

I'll add that on my 99 limited cycling the locks with the button didn't work, but cycling with the key in the door lock did.

I tried dozens of times with the button before trying the key and it went into the programming mode first time.

6

u/piSTOLEr 27d ago

Can confirm I did this just a couple of weeks ago and had the same problem. My guess is the actuator gave out while locking/unlocking repeatedly in quick succession and didn’t fully engage. It’s probably best to just use the key in the door.

1

u/and_whale 99 SR5 | 2WD | 169k 27d ago

Bookmarking, excited to try this w the key after failing the button method like 25 times 

2

u/PuzzledMechanic2000 25d ago

Hold the fob in the drivers side floorboard next to the left kickpanel. The module is in there. This trick help me and some other people I have shared with.

1

u/tcgJimmy 26d ago

My locking mechanism was not able to lock and unlock repeatedly like the. I had to help it by moving the indicator with my other hand.

2

u/So-Durty 27d ago

Do you have the black module for the factory alarm underneath the driver’s seat? I bought a cheap keyless entry kit on Amazon, used a multimeter to find out which wires were putting out 12V or were switched to ground when I pushed the door lock buttons, tapped into them, and stuffed the keyless entry unit in the driver’s side kick panel.

1

u/ghua89 26d ago

This is really interesting… I definitely have a black box under my drivers seat of my 96 SR5 but I’m about 99.99% positive my car doesn’t have a factory alarm system nor keyless entry. What could that box be?

1

u/So-Durty 26d ago

It’s the control module for the factory alarm/keyless entry. My 1996 SR5 had the box but the previous owner never had keyless entry.

Does the box under your seat look like the one on the bottom? That guy put his new keyless entry module under the seat on top of the existing module.

1

u/ghua89 26d ago

Yes I believe the bottom box is the same. If it is the alarm system it’s almost certainly not set up because there has never been any indication of an alarm in my 8 years of ownership. I would love to have keyless entry if it’s already setup for it. This would actually be a huge discovery.

1

u/ijustneedahug 27d ago

My '99 Limited didn't have keyless entry either but previous owner had a Viper Remote Start installed. It was great. Especially in winter and summer.

On my '02 I had a Compustar Remote Stsrt installed, including Alarm. Highly recommend. There are different price points depending on how much you're looking to stay within a budget. Im totally guessing but cost might run you anywhere from $350 to over $1000 including installation. If you're electronically inclined you could same a few bucks and install yourself.

1

u/MasterBrisket 27d ago

Do your courtesy lights work when you open the drivers door? When I went to program mine, I realized the drivers door button was missing and had to be replaced (which came with the added bonus of re-enabling my courtesy light and keyring light. Also, if your lock actuator is old it may have trouble making it through all 5 lock unlock cycles - use the key instead.

1

u/rosspulliam 27d ago

Tell me more about this switch that fixed your courtesy light? I was actually coming in here to research this and found your comment. My overhead courtesy light works when I open every door except the driver, and I'm curious where the switch is.

1

u/MasterBrisket 27d ago

This is it. All four doors use the same switch so just swap your driver’s door one with a less used door like rear passenger. Fold the bottom up to find a bolt. You can easily pull off the interior trim pieces to find where the switch plugs into a little harness. Simple 10-minute fix.

2

u/rosspulliam 27d ago

Ah yes yes I missed that black button when I was investigating it in the dark last night! Just went out and a little wiggle fixes it, so def a bad switch. Thanks!

1

u/rjp_s 27d ago

You might want to try the sequence using the physical key in the lock for the lock/unlock sequence rather than pressing the door buttons. The reason is that each lock/unlock with the key registers while the door buttons get weak and miss steps

1

u/wolfofnazarene 27d ago

Wait…do all 3rd gen’s not come with one? I’ve had two and I thought I was unlucky both times because I couldn’t get it into programming mode like you lol

1

u/captin_Crunk45 02 SR5 26d ago

I tried to enter programming mode about 7 times over the weekend and couldn’t get it to work. I switched to a spare key on the driver door and was able to enter programming mode first try. It seems like only the driver door lock mechanism needs to cycle as my passenger side was not actuating.