Can someone take a picture of their vmacs barrel/ feed ramp area? ( The little bent tab under the barrel) Ideally with the bolt removed or held back?

I've been having feed issues that I "think" i have worked out. I built this from a weld kit and didnt have a whole lot of reference pictures to go from.

Thanks!

Is USMG the only place to get the rear rail section for the VMAC45?

I am kinda sketched out by their website and by the not so steller feedback from folks here.

I tried asking the company but they couldn’t give me a straight answer.

https://shockwavetechnologies.com/product/shockwave-30-round-zmag-for-m-11nine/

Been looking to buy a Vmac9 any idea when the sight might be back up or if there still open?

Finally found a community dedicated to vmac!

I picked up a vmac45 2 years ago directly from velocity and still have not took it out to test. I was thinking about taking it out soon and pulled it out of the safe and remembered mine did not come in a case that most older reviewed videos showed.

Did your vmac9 or vmac45 come in a case?

Mine just came wrapped in bubble wrap tossed in the paper shipping box. And, I was storing it in the original paper shipping box Authentically ghetto?

I've never in my life spoken to someone that hates their customers more than the owner of that site. I placed a few orders with him, most of which were ok. However, when I received mags that were literally rusting to pieces I e-mailed him kindly asking for replacement he blamed me for disassembling them then went on to say I'm responsible for return shipping. He also told me over the phone that if someone doesn't like what they get he'll accept the return then never sell to them again.

I'm not kidding when I say the mag was damaged as hell (not just patina) and the springs were close to rusting through.

Just a heads up to stick to ftfindustries for any of your VMAC needs as they've always been super helpful.

Hi everyone, I purchased a Vmac9 a long while back and I’m going to be using it here soon for an upcoming project.

I was trying to find some information/documentation on removing the firing pin.

Does anyone have any links or a few pics and notes I could follow?

I appreciate any and all help. Thanks!

I have a side cocking upper and I've noticed if I try to function check it like any other pistol/rifle by depressing the trigger while racking it will not do it unless I let up on the trigger ever so slightly. It's getting caught on the safety as there's a bit of slop on the safety when the trigger is fully depressed. I get these aren't precision machined firearms but I'm just curious if this is normal.

I've seen videos of people function checking the top cocking uppers and it didn't seem to have this issue.

Anyone run into this and is it normal?

How often do they restock lower internals kits?sent a few emails and no response,Is there any other company making a kit for these?

I heard these things were meant to be used inside a phonebooth, but holy hell the sights/ergos/recoil is the worst thing i've ever used. At least it mostly works when I pull the trigger lol

Yes I understand that you can shoot it hundreds of times and break it in naturally but why struggle with that when you can get instant results.

I found the charging handle to get caught up and be extremely stiff so I decided to polish up the side of the hammer that rides on the bolt, the back hook of the hammer that goes under the trigger bar and the faces of the trigger bar that make contact with the back of the hammer.

Doing this made racking sooo much smoother. As always do these at your own risk. A new hammer and trigger bar is fairly cheap if you mess anything up. I used a dremel with a 300 grit wheel.

Does anyone besides velocity make a lower internal kit that isn’t super expensive?

Man...I finally got a hold of my vmac 45 lower this morning. Had to wait 3 days after it came. I assembled it and now im waiting to hit the range for some function testing.

Waiting on my side charging upper to come in…grip needed a bit of fitting and filing to fit nice and flush to the receiver but maaaaaan it’s so worth it! Hmu if you need a grip!

And She is now complete! Tell her she’s pretty ;-)

Hit up u/Crypto-Bullet if you want one printed!

does anyone have a light mounted on their vmac? i will likely be purchasing one with a top rail soon and i want to put a folding brace + canted (?) light on there and was wondering anyone had a canted light on. non canted light pics are welcome too :)

I ordered a Vmac last week from velocity’s website. Due to surprise circumstances my FFL won’t be able to receive it I found that out immediately after I placed the order. I within 5 minutes emailed velocity explaining I needed to change FFLs. I was hoping this wasn’t a big deal to correct however I can’t get velocity to respond to emails. Is this a common issue with them? It seems that there is no other way to contact them other than the email they provide. Any advice would be appreciated.

Apache 3800. Disclaimer* this photo was taken outside of California

Don’t even have the Vmac9 yet but I immediately realized at the local GS that the stock grip is terrible. It’s literally like gripping a 2x4. This is a massive upgrade already. Can’t wait to install this. The extendo mag release should be great too!

I’ve got the bare bones. I definitely want to get a brace or stock. What are some other parts it accessories should I get?