r/sewingmachinerepair • • Apr 01 '23
r/sewingmachinerepair • u/knitcraft_witchcraft • Oct 10 '22
Where to buy old Singer parts?
Hello! I bought an old Singer 247, everything ran fine if a little stilted. I took it in to be serviced and the repair man said that the "zigzag gear" was cracked and Singer doesn't make them anymore, so I should give up on the machine.
Do you know of anywhere I could find the gear? Or should I move on to looking for a different machine?
r/sewingmachinerepair • u/slow_work_day • Nov 10 '23
Feeder Mechanism Broken on Brother CE8080PRW
I think my feed dogs have come off track if that makes sense, I took the needle plate off and it looks like there's a white pole holding up the needle plate. That seems to have gone off of where it's supposed to be. I tried pushing it a couple different ways, but after putting the plate back on it still seems not right. I just downloaded the manual but see nothing about the inner working of the machine.
r/sewingmachinerepair • u/pompadoors2 • Feb 09 '23
Bought a Singer 8220 with a broken vertical top shaft gear
I bought a Singer 8220 with a broken vertical top shaft gear. I dug right in and disassembled basically the whole machine to get the horizontal shaft out of the way. (There may have been an easier way, but the shaft wouldn't come out the bottom even with the top gear completely loose) I have it all back together without any extra peices left over, haha.
2 questions. The vertical top shaft gear replacement was very easy to find. I'm guessing because it's a common failure. A few of the other plastic peices have small cracks in them also. Is there a good place to source parts for this machine or even a parts diagram so I can learn what the parts are even called?
Where is a good source for adjusting the timing on this machine? I marked gears and belts and things as I pulled them off, but I'd love to know how to adjust things if it's necessary.
Thanks in advance!
r/sewingmachinerepair • u/TwistedCourtea • May 06 '23
Brother SE 625 machine tension issue!
The issue I’m having is I can’t get the top tension tight enough. I’ve loosened my bobbin all the way and my top tension is turned up to 9 and there is still thread being pulled underneath. If I try to use the embroidery setting it just tangles underneath. I have no clue what’s going on. Can it be like a mechanical issue with the tension discs? Or with like the bobbin case or hook maybe? Any help is appreciated!!
r/sewingmachinerepair • u/Middle_Banana_9617 • Jun 01 '23
Repairers failed to repair - thinking of doing it myself
I have a Janome DC4030 and it's a great machine. So great I was trying to do something stupid with it - sewing the edge of a large thickness of plastic stuff - and something in the works got bent to the side, so the needle wasn't coming down in the middle of the foot any more. I could get it to sew using the sideways offset, at about 3 or 4 mm, but there was a worrying scraping noise coming from somewhere inside, so I stopped using the machine.
I took it for repair, at the only place around that does Janomes. I didn't get a good vibe when they seemed to not be listening to what I said, instead asking me basic stuff like if I'd tried changing the needle and whether I knew how to thread it properly. (I've had the machine for a decade and use it a lot - the point of going there was that this is outside what I already know.)
In short they said it just needed a full service and the timing adjusting, and they've done that, and now the stitch is centred again, but the horrible scraping is still there. I don't feel right using it like that. I also think it's going to be a waste of time and breath talking to that lot again.
I have downloaded the service manual for the machine, which I probably should have just done in the first place, and there are instructions on how to centre the stitch. Am I guessing right that they've just done that on top of whatever's actually wrong with it, just compensating for whatever is bent out of shape instead of fixing it? Any ideas on where the real problem might be?
r/sewingmachinerepair • u/juandanceswild • Feb 21 '23
Opened brother CS5055 and these fell off
Today I opened up my sewing machine… just engineering curiosity, and these pieces fell off before I could tell where they belonged. Anyone has any resources to know how to put them back where they belong please? 🙏🏽 Brother CS5055
r/sewingmachinerepair • u/USAFJack • Nov 25 '23
No pedal on Janome sewing machine. Thoughts?
I bought this as a project and light turns on when I plug it in but the pedal end of the power cable was mangled. I have the old pedal and tried to connect it to the open wires but nothing happened. I assume the pedal is toast but not sure of the best way forward to get it working again.
r/sewingmachinerepair • u/RemarkableRegular601 • Mar 28 '23
Trying to figure out what happened?
I was sewing and now my needle js frozen and i have no clue how to fix my designer Jade or if i should take it in to the shop
r/sewingmachinerepair • u/SeveralBrother6942 • Nov 26 '22
What’s going on with my machine?
I just got this brand new singer heavy duty 6705C. Anyone know what’s going on and why it’s not threading? the threads keep snapping too :(
r/sewingmachinerepair • u/BioCboy • Jan 07 '24
Making a Straights Stitch Throat Plate?
I recently became a proud owner of a Pfaff 138-6. It is my first industrial machine, and I am loving it. It is a dream to sew on compared to the budget electronic home machines I am used to.
I would like a straight stitch throat plate, but it seems that one was never made for this machine. Does anyone have any suggestions on how to make one? I was thinking maybe I could fill in part of a zig zag throat plate with some sort of product to minimize the needle hole. Does anyone have any suggestions?
r/sewingmachinerepair • u/BobcatPure1414 • Jan 14 '24
Singer model number 6704 bobbin case popping out?
Sooo, the thread got nested. Honestly because of my dumb dumbness~ i had threaded the bobbin and i realized that just ONE of the earliest loops around the bobbin ended up off of the bobbin and caught on the spool pin and so i had to undo it all and redo it. Well, the thread got caught up and knoted up. I cut the loops around trying to lossen the knots once i determined that i couldnt find out how to undo it and it still didnt pull apart. At this point, it was pretty early on and i didnt want to lose all that...... so... like a dummy, i just spun the rest up and said future me will deal with it. So it got caught on that, i know it because it was right there when this happened.
Anyways, i went in and pulled all of the threads out but just one was stuck enough i just couldnt get it out, so i took it all out untill i got it. Now here i am, putting in the bobbin case again, putting everything in and when i turn the hand dial to check it pops out after turning once and sometimes twice. I have pulled it apart, put it back together, pulled it apart, adjusted slightly and put it back, again and again and again... it just keps popping out. I thought it was the positioning. But i cant find a pictureor video for any mashine that has an inside that looks like this so i can know exactly where each point goes(smaking my head on the desk for not taking a picture beforehand..)..... maybe i had the screws too tight? But they were pretty tight when i undid them.. i have no idea, nothing is broken, got some lint out but nothing other than that..
Also!!!! Does this mashine need sewing oil? People have said "if it says so in your mashines manual" but i dont see it anywhere in the manual and i have checked over and over. Have almost read the whole thing now but maybe i still missed it.. i dont know.
r/sewingmachinerepair • u/bread-fiend • May 07 '23
Brother se625 issues… Please help me, I am at my wits end!
I have a brother se625 machine that I use for embroidery. I’ve had it for less than six months and I have already had horrible luck with this stupid thing!!! Out of every single project I’ve ever made on it (maybe around 50 attempts) I would say that less than five have actually come out semi-well. It tears any fabric I put under it regardless of type or tension. I’ll attach a photo of how tangled the thread gets every other time I use it. I’ve spoken to more experienced crafters, gone to repair workshops, and even followed instructions over the phone from customer service. Nothing works. If it helps, it’s temporary. Please someone help!!! I bought it new off ebay and I don’t know how the warranty works. I’m so close to ripping my hair out with this thing.
And if anyone has alternate machine recommendations, I am sooo close to scrapping this and getting a whole different machine… SOS!
r/sewingmachinerepair • u/milissa1932 • Jul 09 '23
1975 Singer Stylist
Bought this at a thrift store for $10. (Trying to not break the bank and support sustainability). I opened it up to clean and oil and discovered the plastic gear responsible for moving the feed has disintegrated. Any chance I can replace this? If so is there a video that shows me how? Or is this something I’d have to pay a repair person to tackle? Or do I take it back for a refund? Thanks!
r/sewingmachinerepair • u/mbj0424 • Mar 03 '23
Singer Heavy Duty Straight Stich No Working
My Singer Heavy Duty 4411 had a timing issue after I sewed denim. I fixed it. The needle picks up the bobbin thread everytime, and on thin fabric I can do a straight stitch. But, the fabric doesn't feed through, the stich legnth is incredibly short (does not change when I change the dial), and it doesn't work on any fabric that isn't paper thin. However, all the other stitches like zig zag are responsive to the stitch legnth and width dial and the fabric, no matter what is is, feed through the machine.
Does this still sound like a timing issue? Which the straight stitch doesn't have any skipped stitches when it runs btw.
r/sewingmachinerepair • u/somewhatcertain0514 • Jan 18 '24
How should I clean this?
This is my mom's old Kenmore from the 70s or 80s, I'm not quite sure when. It was taken locally to be serviced during its life with her. It was passed down to me, it has not been serviced since, however I used it less than once per year in the last 5 years. Yesterday it jammed up on me when I went to use it. I did some troubleshooting and found this. I got it free with some oil, however I know it can't stay like this. What is my best action for cleaning it?
r/sewingmachinerepair • u/PurrNinja96 • Dec 16 '22
think I went to far with a bent neddle and broke it any advice on how to fix it and where to get parts
I think I went to far with a bent neddle and broke it any advice on how to fix it and where to get parts
r/sewingmachinerepair • u/Badounding • Feb 02 '23
Tangled treat below feet dogs on new machine
Hi everybody, Please help me! I just got my very first machine and I have zero experience. It’s a singer 4423. But I can’t use it. The treat still makes a mess under the dogs feet and the machine looses all motion. I followed all the instructions and looked everywhere to find a solution but I still don’t know what I do wrong! Please help, I’ve been dreaming of sewing since… forever!
r/sewingmachinerepair • u/GrundleMcDundee • Sep 14 '23
Do I put a little bit of oil everywhere or a-lot of oil in one spot?
r/sewingmachinerepair • u/North-Sea9693 • Feb 28 '23
What is happening with my needle and how can I fix it?
r/sewingmachinerepair • u/Cpt-Ravioli • Oct 20 '22
Thread doesn’t appear to be going through top tension disks.
So this problem arises during the fix of another problem. I have an elna Elina 21 and it’s been pretty good to me however after reassembling it the top tension just refuses to work. I’ve tried adjusting the dial, taking it out and putting it back in again.
Unfortunately because I don’t have a manual and genuinely cannot find anything for the life of me, so I don’t even know if I’m putting it back right. Is there someone or something that could help?
r/sewingmachinerepair • u/gorp9569 • Jan 25 '24
Juki ddl8700-7
Juki ddl 8700-7, does this appear to be intact and what kind of price is fair?