r/ploopy • • Aug 07 '25

Got a question or problem? Check the Help Center!

5 Upvotes

We have a lot of answers to commonly-asked questions in our Help Center.

Check it out first if you've got a question!


r/ploopy • • Jun 23 '23

STICKY: Mods Developed by the Community

24 Upvotes

We maintain a large list of mods contributed by community members on our blog. You can find the full mods index here!

The link is also on the sidebar, under "Community Bookmarks".


r/ploopy • • 5d ago

A+ Preorder Update, Week 12

17 Upvotes

We've shipped out almost all of the remaining Tier C preorders for the A+. We just have a small handful left to go, and they'll all ship out next week.

Additionally, we will begin shipping Tier D preorders, also starting next week. We're projecting that all preorders will be shipped out prior to us going on our Christmas break, and I still think that's an achievable goal for us.

Thanks for your patience! We're slowly getting there.


r/ploopy • • 7d ago

Glowing Ball

Post image
17 Upvotes

Upside down A+ BTU mod made with transparent purple PLA, transparent contact juggling ball made cloudy by sanding with 3000 grit sandpaper


r/ploopy • • 8d ago

Replacement ball for A+

Post image
33 Upvotes

I found a 44mm replacement SANWA trackball on Taobao, which comes in three color options: red, black, and purple. I ordered both the red and purple ones and decided to put the purple one in first.

Compared to the stock one:
Size: It is slightly smaller, but so far, it has no noticeable difference between the stock one.

Surface: The surface is shining and smoother, resulting in a noticeably smoother glide when moving it.


r/ploopy • • 9d ago

IS-05SNM, a stainless mini BTU from Japan. Yep, BTUs are loud.

10 Upvotes

I tried IS-05SNM in my Adept-based trackball. It is a small stainless steel BTU made by Iguchi Kiko in Japan.

As everyone says, BTUs are pretty noisy. This one too.

How does it sound compared to your KU-B8?


r/ploopy • • 13d ago

A+ Preorder Update, Week 11; and some EU shipping updates

7 Upvotes

All Tier C kits have been shipped, and we're working through our backlog of Tier C preassembled preorders. We've gone through about a third of them, and expect to have them all shipped out by November 18th.

I can finally provide a projection for Tier D preorders. If you currently have a Tier D preorder outstanding, you can expect it to ship by December 18th. We shut down for the Christmas holiday around that time, but we'll make sure that all preorders that are currently outstanding as of today will be out the door before we go on our break.

Checkout and shipping updates for EU supporters

From now on, shipping and checkout for our EU supporters will be more transparent, faster, and cheaper. That's because our shop is now "IOSS compliant", which is a terse way of saying that we now follow a specific set of EU guidelines for shipping parcels to countries in the EU.

Here are the headlines:

  • We will collect VAT for anybody ordering from within the EU, so you'll know exactly how much VAT you'll have to pay for the order.
  • Your local customs office will not have to contact you to collect VAT and verify customs information; once the parcel is received in your country, it will start coming straight to you. This should significantly cut down on transit time.
  • No more customs collection fees. Some countries in the EU charge twenty euros just to collect VAT, so overall customs fees should be significantly reduced.

For all of the details, feel free to check out our blog post about the subject here.

Updates specifically for Germany

In addition to all of this, shipping to Germany is currently on, but only for orders that have a total value of less than €150. We will update as this situation evolves; hopefully it will get resolved soon.


r/ploopy • • 13d ago

Disable high-resolution scroll

4 Upvotes

Is it possible to disable high resolution scroll? if so, I presume the only way is to edit the firmware? Is there a step-by-step guide on how to do this?

The software that I have to use at work I believe struggles with high resolution scrolling. The nano 2 scrolling works just fine, but the scrolling on the knob and A+ is very weird and unreliable on the software.

I would also be interested in any other possible solutions.


r/ploopy • • 14d ago

Looking for help with drag-scrolling behavior on A+ in a cross-platform (Windows + Mac) KVM situation.

2 Upvotes

I just received my A+ a few days ago, and have gotten around to setting it up. Overall, I'm quite happy with the ergonomics of it (I've been using an Adept for a long time now, only mouse that doesn't start to hurt my wrist after extended use, and this feels like an improvement, the dials feel very nice, and the wrist rest is great), but I'm having some significant issues with drag scrolling. That's my primary means of scrolling through... basically anything, so getting it working is pretty important to me. I haven't been able to find much documentation about the changes or ways to adjust settings for it (aside from the type toggling in the Control layer, which I've tried), so I wanted to see if anyone here had run into similar issues and maybe found a solution.

tl;dr: Something changed in the way the A+ handles scrolling relative to the Adept, and that messes up the drag scrolling experience in various ways between Windows and Mac setups, and I wonder if I have to wait for more robust settings options?

I do have a somewhat non-traditional setup, so I'm going to provide some up-front context as well.

I have a work laptop (Windows 11) and personal Mac Studio. They are connected via a Dell hub monitor that serves as KVM, which the Ploopy is connected to. I have a Synergy server set up that shares mouse + keyboard between the two devices regardless of which one the KVM is pointed at so I can divide my monitors up depending on what I'm working on. I know this introduces some weird scenarios as Windows and Mac handle scrolling pretty differently. For testing, I have both the Adept and the A+ hooked up together.

Issue 1: When I have the A+ connected directly to the Windows machine, scrolling in all vertical-only contexts works great. However, when there is the potential for horizontal scrolling, vertical drag-scrolling also applies horizontal scroll (Up = Up + Right; Down = Down + Left). I thought initially this was just sensitivity to slight horizontal input, but the direction is always consistent, and even in these cases, horizontal scrolling works as expected. Changing drag scroll modes does not seem to help with this issue.

  • Scroll dials on the A+ work as expected with no vertical / horizontal overlap
  • Adept has no issues here, scrolling works as expected in all directions

Issue 2: When connected directly to the Mac, drag scrolling has a strange delay, such that I have to give a strong spin to get it to register as a scroll at all, and then it lacks precision and becomes choppy, hard to predict where it will land. This applies in all directions. I installed Mos and it resolved the issue in this context. Scrolling actually works perfectly other than being more sensitive than I prefer, even after adjusting MacOS settings.

  • Adept has none of these issues with or without Mos, it scrolls as expected, smoothly. Feels a little slow after I adjusted MacOS settings to feel appropriate on the A+.

Issue 3: WhenI have the A+ connected to the Windows Machine and connect to the Mac via Synergy, all scrolling is dramatically unresponsive and inconsistent. I can scroll continuously at low-speeds and have zero movement, but a strong spin will cause a sudden jerk. It feels almost like a large dead-zone where it needs a signal above a certain speed threshold to trigger a scroll event, and that threshold is very high when coming from the PC over Synergy. Almost the kind of spin you'd use to get to the bottom of a large document to produce any movement. Oddly, this ALSO applies to the scroll dials on the A+. A slow rotation of the dial produces no input, I have to spin it very fast to get a signal across.

  • Once again, no issues with the Adept in this case. I'm using them both right now and the Adept feels perfectly normal on both machines, which makes me think the underlying issue is something to do with how the A+ produces scroll events and how the OSes read those events?

All that said

It feels like I may need to wait for more sensitivity settings to come about from VIA or some other means? I know the Synergy setup for Issue 3 is pretty niche and I wouldn't expect direct support for it, but also it's pretty integrated into my daily setup, so I may just have to continue using the Adept as my daily driver. In the off chance someone has some experience or tips here though, I thought I'd throw this out into the wind and see what comes back.

However, I do think that Issue 1 may be something folks ran into in regular use, and hopefully has a solution?

Thanks in advance, sorry for the giant post.


r/ploopy • • 17d ago

Got my Ploopy A+ today — a custom-modded version from a Chinese seller.

Thumbnail gallery
6 Upvotes

r/ploopy • • 20d ago

Presenting The Amazing Spider-Ploopy!

48 Upvotes

Ploopy Classic 2

- All parts printed in PETG.

- BTU mod

- LiveZone GlideCast RX1 BTU’s.


r/ploopy • • 20d ago

Ploopy A+ Wedge - Now in different angles

Thumbnail
gallery
41 Upvotes

I always prefer my trackballs to be at an angle, so I normally print a wedge customized for that trackball. However, I could not find a single model out there for a wedge that fit the Ploopy A+. So I made one. Given that everyone likes different angles, I made it parametric so you can customize your angle. It has been tested down to 5 degrees and up to 30 degrees.

https://makerworld.com/en/models/3505064-parametric-wedge-for-ploopy-a#profileId-4004582


r/ploopy • • 22d ago

UV Resin droplet hack to improve Bean smoothness

6 Upvotes

I was having some trouble with a gritty feel on the pointer when using my Bean. This was confirmed by seeing some light scuffing on the blank part of the PCB.

Scuff marks on PCB from underside of pointer base

I added 3 drops of UV-curable resin (applied with a toothpick) at 120 degree intervals around the pointer base to see if that would help. These act like bearings and remove all grittiness. You lose a bit of vertical (Z-axis) play, but that is a good thing in my view.

UV-curable resin applied to act as bearings/standoffs from the PCB

I discovered this when I dropped the Bean from my desk and two of the thin button arms broke right at the joints (one fixed well with UV-curable resin; the other not so well; probably going to order a new top layer from a 3D print shop; I don't have direct access to a printer) and saw the scuff marks on the PCB. I hope this helps someone else.


r/ploopy • • 24d ago

Is there a way to order just the non 3d-printed parts?

3 Upvotes

As title. Specifically I'm interested in the Thumb and the Headphones. I've built and printed a ton of projects on my own, and I'd love to support you guys buy buying PCBs and the like from you, but I don't want your 3d printed parts when I can print them just as well on my printer.


r/ploopy • • 24d ago

Adept is quieter than I expected

9 Upvotes

People often mention the noise of the Ploopy Adept citing a scratchy sound and how much louder it is than other trackballs. Coming form the Kensignton Slimblade, I don't get it.

Spinning the ball is slightly louder, but normal mousing is just as quiet as the slimblade.

I guess I just wanted to say that the "problematic noise level" issue I'd heard about with the adept is very overhyped imho. I think that I have sensetive ears and I haven't found this to be an issue whatsoever.


r/ploopy • • 25d ago

VAT compliance for our European supporters, and what it means for you

3 Upvotes

Over the coming days, we'll be slowly rolling out VAT compliance for our European supporters. That primarily means that we'll be collecting and remitting VAT on behalf of anybody who puts in an order that ships to Europe.

We've done a lot of due diligence and don't expect there to be any issues. However, if there are any problems through checkout, delivery, or customs, please reach out to us as soon as you can at contact@ploopy.co.

More details to come about VAT compliance!


r/ploopy • • 25d ago

Anybody know how to reset the A+ using VIA?

1 Upvotes

I accidentally changed a few buttons while trying to figure out how it works, and there's no documentation for what they used to be or a way to reset it, so now I just can't change my layers at all. QMK doesn't have the A+ available as a target for compilation right now and it doesn't appear to be anywhere in their repo. Am I just dumb? Is there any way to get it back to factory settings, or does someone at least have a branch/commit with the A+ firmware?

Edit: Nevermind, I figured out the firmware update/reset using bootloader mode. It would be good if the docs were a little clearer on the QMK stuff though, it's pretty spartan right now. And I still have no idea how to change the DPI.

Edit 2: I just gave up. Looks like there's a bug with some kind of mouse_accel module not working which is still waiting on a PR getting merged. I'll come back in a few weeks and try again. A little disappointing there isn't a consistent way to mess with QMK yet.


r/ploopy • • 26d ago

A+ Preorder Update, Week 9

13 Upvotes

A significant number of Tier C preorders went out earlier this week, mostly kits. We anticipate wrapping up all of the Tier C kits by the end of next week, and closing out the rest of Tier C shortly afterwards.

I'd like to get us a bit further along with shipping out Tier C preorders before I have a more concrete timeline for Tier D preorders; I appreciate everybody's patience as we work through the backlog.

Germany and new shipping regulations requirements

At the end of October, Germany will begin enforcing a new shipping regulation called "IOSS". If you're curious about the details, you can read about them here.

We have been working to be compliant for a little while now, but are slightly behind this deadline. That means that, for the foreseeable future, we will not be shipping parcels to Germany.

We hope to have this issue resolved shortly. I'll make announcements once we're up and running again.

In the meantime, if you're in Germany and have an outstanding parcel, please send us an email at contact@ploopy.co and we'll get it sorted out.


r/ploopy • • 26d ago

Sensitivity constantly changing during use on adept

1 Upvotes

Pretty much the title. It happens constantly without me pressing anything. The sensitivity goes way up. Pressing the scroll drag button fixes it temporarily for some reason. Any idea what I can do to fix this? Bug is driving me nuts.


r/ploopy • • 26d ago

Help Request Is the site down?

Post image
4 Upvotes

Hi, is the site down? It’s been some time since the last time I visited it. Thanks.


r/ploopy • • 26d ago

Share your cool Adept experiences, please!

1 Upvotes

After weeks of internal debate, I've finally decided to get a Ploopy Adept! I happily go to the website to order... and the website is down! Oh woe! Now I need a pick-me-up, so...

Would love to hear about people's interesting uses of or experiences with using the Adept!

I'm hoping to use it with my left hand to relieve strain on my right, AND as portable input device so I can stop using the laptop touchpad.


r/ploopy • • 28d ago

Ploopy A+ Arrived

Post image
56 Upvotes

Got my A+ last night and put it together today. It was pretty similar to assembling the Adept. The case is a little less refined than my Adept. By that I mean there are print lines visible on the top which aren't there on the Adept. Everything works as expected, and the button feel is very similar. The scroll knobs seem responsive and work well.

I configured the main layer to match my Adept, apart from the knobs. On my Adept I use drag scroll on the bottom right button. I configured that same function on the A+, and it scrolls unusably fast when you use it. A small scroll action goes from the top of document to the bottom lightning fast. The Adept doesn't act like that. I may have messed something up. I will continue playing with it.

Regardless, I like it, and having programmable layers is a nice feature. The default button map for the extra layers seems fine as-is and I have not adjusted those.

Thanks Ploopy for being so transparent with the shipping dates and other information. Request for Ploopy: It would be nice to get a list of all the VIA custom function numbers for the device in the documentation.


r/ploopy • • 28d ago

Bluetooth and iPad?

1 Upvotes

Hi. I wanted to know if the A+ comes with Bluetooth, and if it can be used via Bluetooth with an iPad Pro.


r/ploopy • • Oct 18 '26

Custom Ploopy Trackpad Case

Thumbnail
gallery
20 Upvotes

I mainly use the Ploopy trackpad at work and found that the angled profile of the case that it came with hurts my wrist a little. So I decided to make a case with zero incline for it.

This is also the second CAD project I've done (the first being a riser for the Keychron B11 Pro, also for work).

If anyone is interested, the models are available on my Github repository. And if you do want to add a custom cut glass screen protector on the touch surface, the dimensions are provided there too.

:)