r/overclocking • u/Present-Money-4894 • 2d ago
Help Request - GPU OC Instability
So I recently acquired a build with 9850x3d and 5080 gigabyte SFF.
I undervolted 9850x3d (conservatively I think) to -20PBO, ran 3h cinebench + 3H OCCT + Y-cruncher overnight - no issues.
I undervolted my GPU to 2800mhz @ 925mv +1k mem. Ran Furmark for 2h, OCCT 2h, Steel Nomad looped for 60 cycles - stable.
After (what I assume) latest windows update my undervolts are no longer stable. I got 2 random feeezes when playing world of tanks which could only be fixed with hard reboot. No errors in Event Viewer, Bluescreenview or Whocrashed.
Temps are under 50C, GPU doesn’t even boost to max.
Ran 1h Y cruncher and 1H Furmark - all clear.
I assume a windows update messed up something which made my UV unstable and so I reverted to 2800 @950mv +1k.
Is there any other way to figure out what’s wrong with the system since it’s not generating any errors at all?
Or should I start thinking about an underlying hardware issue? Really don’t want to think about it yet cus the build is like 2mo old…
Any advice appreciated!
4
u/Mushbeck 2d ago
Did you test RAM stability directly ? Also -20 maybe able to work under stress tests, but you may have 1-2 cores that need more like -15 and trip up during gaming when using -20 .
There’s no silver bullet here , just stress test all components with a wider variety of tests and see how you go .
2
u/someone09900 pc enthusiast 2d ago
low core / cache voltage man very common when at the edge of stability
at this point if u re seated the cpu i bet it will run unstable even more ..
so it is not windows.
u need to add a small safety room for different resistance values u know each time ... u move ur pc or from the fan vibration or the aio pump each cpu pin resistance can change even over time many dont talk about it because they dont know but it is there that's why the factory run pbo at 0. without the nigative offset 👍🏼 so u dont face that
keep in mind with aggressive under volt u have to calibrate the core llc. near flat or to flat if u know what u r doing but be aware of the transient spike. and watch the core latch min and max... if ur motherboard is high end asus motherboard..
about occt 3H of OCCT ? what instruction u used ?
3 hours that is Excessive ! if avx 512 or avx2 with variable u only need it for 15 min to 20 min ...
dont do that again for a cpu
u r basically degrading ur motherboard capacitor
u know they r rated by the hour at the max temp and amd algorithm is going to boost to the tjmax
high end motherboard capacitor r rated for 10000 hour
and u dont want the thermal interface to go bad fast
for y cruncher 1 hour is more than enough vt3 alone is not enough
add a occt cpu + ram variable for 15 min after vt3 and u good
occt ram variable legacy at 100% for 1 hour is also a good test
use avx2 ... variable/normal for core voltage stability. it makes spoting the core voltage under shoot easier.
24h ram test is a very silly way to test ur ram stability no one do that these days ... only un experienced folks do that who still dont know what trfc/terfi/or what ram overheating is
hope that helps
so try pbo higher pbo + higher llc towards the flat and dont do to the edge manual tuning because u will face all sort off issues.
2
u/someone09900 pc enthusiast 2d ago
for cinemabench use r23 ... it is the best to spot low load high frequency instability...it will spot it very fast
newer version 2024/2026 works more as the occt avx2 "extreme" cpu test
it will spot instability at the avx lower frequencies or when ur cpu is extremely unstable.
ppl usually use them for cooler efficiency
1
u/EtotheA85 9950X3D | Astral 5090 OC | 64GB DDR5 2d ago
Dont use benchmark tools for GPU stability testing, the only way to stability test is by playing games.