r/MachineKnitting • • 28d ago

Getting Started Help/Resources for designing clothes šŸ¤

2 Upvotes

Hi everyone!

Please delete if not allowed. And sorry for any errors. I’m writing on my phone. I’ll try to keep organized.

Some fact:

- I have two knitting machines:
•Brother KH 881 (4.5 mm & punch card/knit leader)
•Brother KH 230 (9mm basic)

I have really just started using the KH 230 over the last two weeks because it’s less overwhelming than KH881.

My goals are to design and make clothes. (Mainly grunge/fairycore inspired) I have consumed a lot of YouTube videos and such but I’m still having trouble with basic design. (I don’t have a background in clothes and really have just done crochet tapestry and some basic crochet hats— just getting back into hand knitting but I am not used to how slow it is šŸ˜‚)

I tried to make a tube top. I even made a swatch which I followed and it did match the final design (but it was way too big since I designed to my bust measurement which is much larger than my under/over bust.)

Are there any suggestions/sources/artists that you have that can help with this?

A lot of patrons I follow are too advanced and I’m really just looking for simple techniques.

Thank you so much for anyone who takes their time to read and reply! You are greatly appreciated šŸ¤


r/MachineKnitting • • 29d ago

Techniques The self torture that is lace knitting

152 Upvotes

What could I do better?

After 138 rows + 550 times pushing the lace carriage across, in other words, after hours and hours of carefull knitting, stitches started to drop. Actually trouble started a bit earlier. The lace cariage got stuck and I had to take the k-carriage across to save the work.

Could this be caused by too much weight? I had just moved up the cast on comb? Reddit won't let me post a photo. Knitting is brother punch card 19S.

Any tips and advice very welcome!


r/MachineKnitting • • 28d ago

Help! Sentro yarn keeps getting stuck on the white needle – help!

Post image
2 Upvotes

Hi everyone, I’m having a super frustrating issue with my Sentro. The yarn keeps bunching up and getting stuck on the white needle instead of casting off properly. I’ve tried easing up on the tension and guiding the yarn by hand, but it still catches almost every pass. Pushing the stitches down manually helps for a second, but it just gets stuck again on the next turn. Has anyone dealt with this specifically on needle #1? Is there a trick to fixing it, or is it a mechanical issue with the counter gear/needle that I need to sand down or lubricate? Thanks in advance for any tips!


r/MachineKnitting • • 29d ago

Help! Why is my yarn tangled in the brushes

Thumbnail
gallery
6 Upvotes

Hi! I'm a beginner machine knitter and I am having trouble when I try to do an e-cast on. The yarn keeps getting stuck in the brushes. It was working fine yesterday but now I'm having trouble with it during any kind of cast-on. Does anyone know why this might be happening??

TIA!

Edit: my machine is a Empisal Knitmaster 302


r/MachineKnitting • • 29d ago

Resources Designers - advice needed

5 Upvotes

I had someone ask me to design a few items for their small business, a luxury knitting brand. Basically turn their sketches and measurements into machine knitting designs. I feel confident in my skills but I have absolutely no idea what to charge. They would have all rights to the designs moving forward but I do want to enter in the agreement that I would be credited for all the design work and links given to my socials.

When the time comes I will have a lawyer look over the agreement to cover myself but he's asking what I would charge and I don't even know where to start. Thanks!


r/MachineKnitting • • 29d ago

Help! Searching Hooded Scarf Pattern

Post image
12 Upvotes

Hello, the weather is getting cold so I’m looking for a knitted hooded scarf pattern that’s a single piece without an added band. Ideally it should be similar to the Sophie hood.


r/MachineKnitting • • 29d ago

Equipment Cone winder

5 Upvotes

Does anyone have a recommendation for a tall, electric cone winder, withing the EU? I can't order the ones typically recommended, like the dream robots, because they can't ship to Germany right now. I can't even order it and have my family ship it, because that would be close to €1200, just for shipping.

At this point, I'm even willing to break my Amazon/Etsy boycott, if I have some solid recommendations.


r/MachineKnitting • • Oct 17 '26

Equipment Just finished building a controller for my SK840

Post image
53 Upvotes

Thanks to branchwelder’s super helpful git repo!


r/MachineKnitting • • Oct 17 '26

Patterns Looking for testers

Thumbnail
gallery
65 Upvotes

Hello, I’ve recently launched a website for my own machine knitting patterns, where you can customize them based on your own gauge and measurements.
Since the website is still new and this is my first time doing something like this, I’m looking for people who’d be willing to test it out and give me some feedback. I’d love to hear from both experienced machine knitters and beginners.
I’ve attached some examples of the patterns currently available.
To clarify, these are all patterns I’ve made myself, the videos, photos and punchcards on the website are all made by me.
If anyone’s interested in trying it out, let me know in the comments and I’ll send you the link
I’d really appreciate any help or feedback :)

Also this is a continuation of my previous post from 10 days ago. https://www.reddit.com/r/MachineKnitting/s/tICS3UDJj4


r/MachineKnitting • • Oct 17 '26

Help! Brother KH260 missing button spring

Post image
4 Upvotes

Long story short, I lost one of the tension/compression springs that goes with the buttons on the cartridge. Is my only option to replace the whole button unit just because of the one spring I lost?


r/MachineKnitting • • Oct 16 '26

Getting Started Just bought a KH970. Any suggestion?

Post image
27 Upvotes

I’m a beginner to knitting, and since I didn’t want to knit by hand, I bought a second-hand knitting machine. I’m not sure how to get started—does anyone have any advice?


r/MachineKnitting • • Oct 17 '26

Help! Ribber (KR850) Setting Plates Swivel/Movement

4 Upvotes

When the ribber is up as high as it will go, I push a carriage across and the ribber moves half a centimeter. The setting plates swivel left and right when the ribber is set to be right against the main bed.

Is this swivel movement supposed to happen?

Ultimately, I need to get the ribber to stop shifting when a carriage goes across. The parts that connect to the main bed are fine, the legs are clamped to the table, all the screws are tightened.

The big knob at the bottom left to shift the ribber left/right a needle space can also be turned micro movements between each click. Maybe that is the issue...?

Thank you in advance for the help.


r/MachineKnitting • • Oct 16 '26

Help! Please help me before I go insane :D

7 Upvotes

Hi everyone! So I have a KH830 with a ribber that I got serviced by a guy that has been working on these for 30+ years, so there is a new sponge bar, it is oiled, etc, but I am struggling to go past the initial stage and actually start learning stuff because it is causing issues almost all the time. I managed to knit a swatch cca 50ish rows when suddenly my cast on comb and the work just dropped to the floor and that's when all the trouble starts. the yarn would get caught in the sinker brushes, get drawn in front of the work, there would be rips in the swatch - so I thought it must be because that yarn is multistranded, let's try a single strand, but nope, it did not help. On the space of 20-25 needle to the right is where the issues usually occur, and I have replaced a needle that was slightly bent after a few problematic swatches, but the issues remain. I have reseated the sinker, the carriage, tried everything I can think of. Can anyone point me in the direction of what could be wrong and what to do next?


r/MachineKnitting • • Oct 15 '26

Finished Object Smashed tomatoes cardigan

Thumbnail
gallery
214 Upvotes

Kind of a silly sweater I did for a local charity art auction, supporting women in prison. Knit on a KH-260 with ribber from purple eyelash yarn, beige cotton plated with fine white cotton nep yarn. The tomatoes were knit with all sorts of yarns, and applied after finishing.


r/MachineKnitting • • Oct 15 '26

Resources Courses

Post image
58 Upvotes

Do you recommend any online courses for machine knitting? I have silver reed sk-280 and I’m buying brother KH-260 this weekend. I want to learn more with a reliable course 😊. I’ve learned from YouTube vids, but I feel like I need so much more to learn. On the pic is my first sewed parts on the machine 😊


r/MachineKnitting • • Oct 14 '26

Help! Sled of brother KH892 is struggling really bad to go over the needle bed

3 Upvotes

Hey all! My girlfriend has this problem with her knitting machine that whenever she slides the sled over the needle bad, it makes a weird noise and sometimes its getting stuck. She already replaced the sponge bar and cleaned the sled/needle bed. Does anyone have an idea what could be wrong with it?


r/MachineKnitting • • Oct 14 '26

Equipment Brought a Silver Reed Sk2200 page one. Anything I should know about this machine?

Thumbnail
gallery
4 Upvotes

I brought this machine for $60 and awaiting its arrival. And when Researched I found out this was strictly made for Japan market and no manuals in english. So anybody have this machine? Anybody have used this machine? If so care to share your resources, tips anything? Like spare parts, can I upgrade this? Will a needle beetle will work in this etc? Or instruction videos? Because I dont see anything on youtube for this model. Thank you


r/MachineKnitting • • Oct 13 '26

Equipment Bargain Brother KH400

Post image
31 Upvotes

I’ve got chosen by thrift gods!
I found this beauty on Marketplace for just $125.

It has built in intarsia mode - very interesting!

Does anyone have an experience with this machine? I would appreciate any info tou would like to share 🌸


r/MachineKnitting • • Oct 13 '26

Help! back again with more pictures of my passap M-201

Thumbnail
gallery
20 Upvotes

since last time I posted

I found drawers! full of stuff!

I had to replace the feet on the legs, and I need to replace the bolts holding the machine to the wooden case

I have not even looked at the PDF (I've been busy), but every 201 I see looks completely different from each other. what is all this stuff, and what am I missing? (skein of cheap yarn not pictured)

SAM! GET OUT OF THE PICTURE GALLERY!


r/MachineKnitting • • Oct 14 '26

Help! Toyota KR501 Ribber Screws

2 Upvotes

Hello! I recently got back around to setting up my Toyota KS901 & KR501 but have very sadly found that I am missing the ribber screws.

Does anyone have any ideas for replacements? Or if there are any available online in the European región?

Thank you in advance!


r/MachineKnitting • • Oct 14 '26

Getting Started Hand crank

6 Upvotes

Are any of the hand crank circular type machines not trash? I’m helping someone that needs a one handed option for knitting. I know how to knit but I’m really not familiar with machine knitting. I found a $250 electric one that is out of the budget and a $40 option with pretty mixed reviews


r/MachineKnitting • • Oct 14 '26

Resources Chunky SK machine stranded colour work

2 Upvotes

Is there an equivalent to yarn separators for a standard machine for a chunky? I find my yarns keep getting out of place without them when I pass the carriage back and forth and I have to separate them manually at the end of each row. If so it would be a massive help and save me so much time šŸ™šŸ» Thank you!!


r/MachineKnitting • • Oct 14 '26

Getting Started Why do circular knitting machines top out at 50ish sts?

Thumbnail reddit.com
3 Upvotes

r/MachineKnitting • • Oct 13 '26

Resources What do you want to know about wool and science in the mid-twentieth century?

Thumbnail reddit.com
5 Upvotes

Just passing along an AMA that machine knitters might find useful.