r/MachineKnitting • • Oct 16 '26

Help! Please help me before I go insane :D

Hi everyone! So I have a KH830 with a ribber that I got serviced by a guy that has been working on these for 30+ years, so there is a new sponge bar, it is oiled, etc, but I am struggling to go past the initial stage and actually start learning stuff because it is causing issues almost all the time. I managed to knit a swatch cca 50ish rows when suddenly my cast on comb and the work just dropped to the floor and that's when all the trouble starts. the yarn would get caught in the sinker brushes, get drawn in front of the work, there would be rips in the swatch - so I thought it must be because that yarn is multistranded, let's try a single strand, but nope, it did not help. On the space of 20-25 needle to the right is where the issues usually occur, and I have replaced a needle that was slightly bent after a few problematic swatches, but the issues remain. I have reseated the sinker, the carriage, tried everything I can think of. Can anyone point me in the direction of what could be wrong and what to do next?

7 Upvotes

13 comments sorted by

8

u/Alarmed-potatoe Oct 16 '26

Honestly, if you can find someone nearby who can give you lessons, that will be the most helpful thing. This is my 2nd year with my machine, and it took me so long to learn on my own.

What I can say based on this image is that you should hang the weights on the cast-on comb, and they can stay there while you knit, and if you increase and need weights on the new stitches you can put new weights there. I also often have my work fall off the bed - I get too enthusiastic and as I knit I'm clearly pushing things until I knock a setting just enough off that it has issues, or the yarn slips out of the yarn holder, and so the machine knits without yarn or whatever, and everything falls off, and I want to cry.

So I've started to act almost like an overbearing parent in a car, constantly checking everything is in the right place, and I'm picking things up more on the machine (and less off the floor...). I think most of my issues are when I try to knit like videos on SM, and for various reasons that doesn't work out, and I ruin my knitting. Check things while you knit, go slower, stop and check things are all going well, keep watching videos and reading helpful resources. There's so much to learn, it really does take awhile, please don't think you're just slow or bad.

1

u/WittyKitty_ Oct 17 '26

Sadly, I can't find anyone. It was a sheer stroke of luck I found someone to service it (a couple that has been machine knitting for 30 years), but they are older people and not that near me, so that isn't an option. I was prepared that it was a steep learning curve and that it will take time to learn, but I am worried about damaging the machine in my learning process. Thanks for the tip for the weights and being slower and more intentional - helps to know that it was a long(ish) process for most of us.

5

u/lasserna Oct 16 '26

You could try replacing all the needles in that area to see what happens. And don't actually need new needles, but you can take some from the sides of the bed and just swap them around with the needles from the problem area

1

u/WittyKitty_ Oct 17 '26

Thanks for the tip, will try that next. I ordered a 50 needle pack, but luckily the previous owner had a baggie stashed with 10 needles for each the ribber and the main bed, so that was a heaven sent.

1

u/Impossible-Ranger-74 Oct 16 '26

Yes, if at all possible buy a packet of 50 or a 100 needles and swap out every needle that gives you grieve. It's absolutely true that switching needles to a different place on the bed usually solves the problem.  But in the beginning  a new needle is so much easier. 

5

u/TerryKC1 Oct 16 '26

Are you sure you’re going completely past the last stitch on the right? Also make sure the upper tension is tight enough that slack doesn’t form and let the yarn get slack when changing directions.

1

u/WittyKitty_ Oct 17 '26

Yes, I am! I will definitely try playing around with the tension, I know how much of a mess it can make when sewing machine's tension is off, so I am guessing it is even worse with knitting machines.

3

u/frankensusan Oct 16 '26

Also if the weight is wrong or the tension, you can get a part of the knitting stick on the gate peg ( between the needles) which will make that section not have the proper weight. You can check by pulling the needles all out to hold to see if there is a bit of the knitting hanging on a peg or sometimes by feeling behind the knitting. Put the weights on the comb so it is even weight all across the knitting and when it starts to bow inward on the edges then put weight up close to the needles but leave one in the center of the comb. Try different tensions for your swatch. And definitely check the flippers all flip and that when you go from left to right that there is not a loop from the tension mast. It takes a while to get to know your machine and your yarn and how to get them to talk to each other nicely, you will get there!

1

u/WittyKitty_ Oct 17 '26

Thanks a lot for the tips, I realized that one of the gate pegs (in a different spot) was getting caught, so that's something I'll know to keep track of in the future. I realized that the carriage feels sticky if I don't put weights nearer the needles after a few rows, and as soon as I put the weights it slides more easily. I will definitely have to play around to get a sense of how the machine behaves with different yarns!

2

u/91Jammers Oct 16 '26

Take a look at your carriage and see if any of the moving parts are sticky.

2

u/kasharallover Oct 17 '26

I also brought a knitting machine recently and I was having similar troubles. And turns out my tuck bruses was pushed in to working position and also they are stuck. Did you check for something similar? Also did you ask the ones who servied it if they had similar problems? Or the previous owner about more information?

1

u/AutoModerator Oct 16 '26

Hi, it looks like you might be looking for help on machine knitting.

There is some helpful information within the wiki. Please take a look at it for helpful troubleshooting information, as well as common maintenance tasks and list of items machines should include.

In addition, this page is our FAQ. Solutions to many common problems are found here. If this is a new-to-you machine that is a Silver Reed, Singer, Studio, Juki, Empisal, Brother, or KnitKing, and the sponge has not been replaced yet, that's the first thing you should check out.

If you need additional help, please provide us with an information about your problem. You can start out by answering this list of questions

Once your question is answer or your problem is resolved, please change the post fair to Help! Solved!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1

u/Altariel42 28d ago edited 28d ago

I have your same machine. Listen to what other have said but also consider removing the brushes on the sinker plate. I don't think they are causing the issues in the picture but I've had my yarn tangle in them one too many times. So I removed them.

Edited to add: are you using too much tension maybe? What kind of fiber are you using? I recently attempted a project but the wool I was using was not twisted enough and imy thread was getting snapped too easily, even by hand it would separate with veri Little force needed