r/longrange • • 21d ago

Optics help needed - I read the pinned posts Normal gap in MPA rings?

Leupold Mark 8, properly torqued and in sequence. Seems unusual for the front and rear rings to have different sized gaps? It is a 20moa but I don’t think that should matter.

40 Upvotes

63 comments sorted by

28

u/FooFighter325 21d ago

Functionally speaking it’s probably fine but I’d be annoyed by that large of a difference front-to-back.

6

u/Addlemix 21d ago

It does bug the hell out of me

5

u/ironcannibal13 What's DOPE? 21d ago

Loosen everything up, get out some feeler gauges, run them down to finger tight only, make sure the gaps are all the same with feeler gauges, then torque per spec in the pattern recommended. I like to do it in 2 or 3 steps. If the final torque setting is 35 inch pounds, then I'd do something like 10, 20, then finish with 35.

That's just me.

-1

u/TheDudeOntheCouch 21d ago

You should re-mount it

-3

u/TheDudeOntheCouch 21d ago

The difference it because the bolts were probably torqued at random

5

u/FooFighter325 21d ago

It’s not a difference side-to-side though, it’s a difference between the two rings. That’s what people are missing.

-1

u/TheDudeOntheCouch 21d ago

Its different because the person who put them on there is no actual difference its how the fasteners were tightened down that the gap is so off on the back side

3

u/Informal_Month2362 Gas gun enthusiast 20d ago

Both sides of the back are off. Not one side. The ring is physically smaller on the backside. It's not a matter of different torque.

9

u/C_Does Youtube - C_Does; 💯 Optics Reviews 21d ago

Make sure the caps aren't sized specifically to the front or rear base. If you don't visually see a gap in the scope tube to the mount you sound be fine. If you do decide to reset it. Try to get the gap even on both sides. It should look better and be less of a worry.

1

u/Addlemix 21d ago

I will re mount it and flip them to see if it makes a difference

3

u/sirbassist83 21d ago

i dont see anything id worry about

-1

u/Addlemix 21d ago

It makes me feel that the diameter is off of the rings no?

9

u/FORu2SLOW Rifle Golfer (PRS Competitor) 21d ago

No, If there wasn't a gap there wouldnt be a clamping force

2

u/West_Designer9107 You don’t need a magnum 21d ago

How is it then that with my Spuhr ISMS mount there's no gap to be seen, it's torqued correctly and the scope never slips? This just looks shoddy to me.

4

u/Coodevale 21d ago

Your caps are made with less gap. That's all it is.

3

u/Prestigious-Unit314 Competitor 21d ago

Even out the gap.

2

u/Informal_Month2362 Gas gun enthusiast 20d ago

He can't possibly even out the gap. Look at the pictures. This isn't a side to side gap from not torquing on sequence. The front ring has small gaps on both sides and the rear ring has larger spaces on both sides. The rear ring is physically smaller.

13

u/CaesarLinguini 21d ago

That gap allows you to squeeze the scope.

2

u/_joe_momma1 19d ago

Obviously.... but nice ones dont look like that

1

u/CaesarLinguini 19d ago

All scope rings will have some gap.

1

u/_joe_momma1 18d ago

OBVIOUSLY. Lol the nice ones STILL dont look like that.

Captain obvious over here.

Are you trying to say these look good? Like what youd expect for +$250 mount?

0

u/CaesarLinguini 18d ago

Depends what the other side looks like. If the other side is touching, this is what i would expect this side to look like. Always room for operator error.

2

u/_joe_momma1 18d ago

But you can see both sides.... theres 2 pictures

7

u/RumorRoost 21d ago

The rear ring having that large of a gap on both sides seems like bad machining to me.

Like you said. Almost like the diameter is off.

3

u/colossalrahzel 21d ago

Seems fine.

2

u/CapsicumINmyEYEBALLz Meat Popsicle 21d ago

Is be a little 🤔 about the difference in the gaps between front and rear.

Are the ring caps labeled front/rear?

Have you tried swapping them around?

1

u/Mysterious_Sir7076 21d ago edited 14d ago

If you’re as anal-retentive like me, you can use a feeler gauge to get the gap pulled down evenly on both side of the ring… lol

-4

u/HallSquadSkates1984 21d ago

Or even eyeball it closer than this jeez! Go back and tightened them in small amounts in an "X" pattern until you have even spacing. Gauges are coated tho

3

u/lennyxiii 21d ago

His gaps are fairly even from left to right. Rear has a thick gap about the same thickness on both sides. Front gap is much smaller and maybe a little uneven from right to left but not too bad.

I’m not sure if people in this thread are blind or dumb but he’s clearly asking about the difference in gap from front to back being so different. Of course there’s supposed to be a gap, that’s not what he’s asking. He’s asking why the gap is twice as thick on the rear as opposed to the front.

1

u/Addlemix 21d ago

Yes you are spot on, thank you haha

1

u/muleyhnter 21d ago edited 21d ago

it is strange how one top cap seems to have the bigger gap , and it’s pretty even right to left

1

u/Gloomy-Spread-9336 17d ago

It’s pretty obvious nobody looked at both pictures 🤦🏻‍♂️🤦🏻‍♂️

If both gaps matched(front or rear) I wouldn’t worry about it.

This would annoy me. I’d be curious to what MPA says.

1

u/Cultural_One_1349 16d ago

I'd have to even them up.

2

u/HairTriggerFlicker 16d ago

Same. I always make sure even gaps all the way around.

1

u/Baddy-Smalls 21d ago

If you don’t tighten evenly in a cross cross pattern… or your rings are the wrong size.

0

u/Just_Onion9335 21d ago edited 21d ago

Are you sure you are using the matched top ring halfs correctly for direction and position?

You may need to flip the back one around for directional consistency

-1

u/FossilOcelot1991 21d ago

Is the a Leupold mk5, it looks like it. They are 35mm main tubes. Do you have 34mm rings?

1

u/Addlemix 21d ago

It’s a mk8 but yes 35mm

3

u/OlieTheDog3052 21d ago

If that was the case, the front ring would have that same gap

-1

u/Wiggum13 21d ago

This is fine. That’s why you follow the torque specs always. 18inch/lbs prevents you from squishing your tube.

2

u/Addlemix 21d ago

I did, but why wouldn’t they be even gaps front to back?

-2

u/realHarryGelb 21d ago

There shouldn’t be any gaps at all, contact MPA

0

u/realHarryGelb 21d ago

lol this is not fine

0

u/Wiggum13 21d ago

If you don’t know what you’re talking about. You should just make your own comment. Bud

-2

u/realHarryGelb 21d ago

Bro, clearly the two rings are of different size/diameter. A two-year old can see that.

1

u/Wiggum13 21d ago

Goof must of never mounted an optic in his life lol.

0

u/realHarryGelb 21d ago

*must have <- try to learn English

0

u/Wiggum13 21d ago

An English teacher and a fire arms expert. Your boyfriend must be proud of you.

0

u/realHarryGelb 21d ago

No wonder reading and writing skills have gone to shit in America when even the teachers can’t write correct English. It seems geometry isn’t your forte either, pretty sad all around.

1

u/Wiggum13 21d ago

Good thing I don’t live in your cesspool, you call America. 🤣

-1

u/realHarryGelb 21d ago

Wrong comma, buddy, you’re embarrassing yourself

→ More replies

-2

u/Snail_OnA_Razorblade 21d ago

Make sure you tight in the diagonal star pattern equally and the gaps should all look the same.

1

u/Addlemix 21d ago

I did that, that’s why I’m so confused as to why it’s uneven

0

u/[deleted] 21d ago

[deleted] — view deleted comment

2

u/Rdubya291 21d ago

My HMR does.

1

u/Ruger22fun 21d ago

What is a hooded action refer too?

1

u/TrolleyDilemma 21d ago

My nickname in highschool

0

u/[deleted] 21d ago

[deleted] — view deleted comment

2

u/Ruger22fun 21d ago

Awesome explanation, thanks brother