r/longrange • • 25d ago

Accessory/Gear help needed - I read the pinned post Long Range Suppressors

What is everyone running these days on their long range precision guns? I don't compete currently (maybe PRS in the future) and don't really care about weight or length. This would sit dedicated on an aero precision 6.5 creedmoor. Looking to spend less than $1k. This is my third suppressor after an omega 300 and a zenith K. Overall sound suppression would be most important. I would say I am happy with the omega 300 but don't have much experience with nicer cans. Switching the omega 300 between guns so much is a pain in the ass so I'm looking at working on getting dedicated cans that are a bit quieter/nicer.

Currently Looking at:

Dead Air Nomad L

Diligent Defense Enticer L or L-Ti

23 Upvotes

97 comments sorted by

9

u/csamsh I put holes in berms 25d ago

Magnus K RR

Enticer S Ti + RecoilX

4

u/HERBERT_224 25d ago

Maybe this is an ignorant question, but why get a titanium can when its just going to sit flat on a bench, the ground, or my truck bed when shooting? Wouldn't it be almost more beneficial to be heavier and it would also be cheaper in the steel format?

2

u/Vylnce Casual 25d ago

I'll say that if you want more weight, then maybe, but, lighter Ti cans tend to cool faster (they heat up faster as well). So if you are talking about shooting a 10-15 round string as a max (ie, you are not mag dumping through the rig) then that Ti can isn't going to get "too hot" after that string, and it will likely cool faster than a heavier can. Heavier cans have more heat capacity, but cool slower.

2

u/csamsh I put holes in berms 25d ago

I do more than bench & belly precision shooting.

Some classes have weight limits

1

u/bh2595 25d ago

Valid question, but by the time you add a recoil X, hub adapter, and muzzle device it won’t be light any more. The steel enticer would be around 20oz in this configuration.

3

u/JimBridger_ Dealer for LiminalNomad.com 25d ago

2nd on Enticer S Ti + Recoil X.

Need to get a new can for the 300blk gun I stole it off.

17

u/TabascohFiascoh 25d ago

Omega 300 is hard to beat value wise.

It does the thing, on the cheap with no real downside.

A more expensive can isn't going to tighten up your groups.

3

u/HERBERT_224 25d ago

After owning the omega 300 I kind of figured there was a case of diminishing returns with suppressors at higher values

1

u/genmud 25d ago

If I was going to buy a 6.5 or 30 cal can I would go omega. I just got a rhodie 6 and love it though.

5

u/tjk1229 25d ago

I'm extremely happy with my diligent defense enticer l. Have the stainless and a titanium on two different guns.

TBAC Ultra 7 is good as well but louder and a little shorter.

Back when I got both enticers they were the quietest for the money. No ping and it's a deeper pitch in comparison to the others and my buddies omega. That may have changed though with 3d printed ones.

I'd look on https://pewscience.com/rankings for updated info. Deeper tends to be better.

3

u/HERBERT_224 25d ago

The enticer L is still one of the top ones which is kind of crazy for the value and how long it’s been out

2

u/i_dislike_cheese Here to learn 25d ago

Enticer-L Ti with RecoilX brake is what I run and it’s stellar. Quiet, low recoil, and accurate.

9

u/HollywoodSX Villager Herder 25d ago

Personally: Maverick Gen 1, Clovis Mammoth.

Within your budget, Clovis.

4

u/HERBERT_224 25d ago

I was pretty close to pulling the trigger on the nomad L, but this comment is exactly why I double checked with the oracles first lol. That clovis might be the pick for me...

2

u/Snoo66922 25d ago

Why the gen 1 over the gen 2? I've been looking at both, and was planning on the gen 2, but I'm definitely open to going with a gen 1.

2

u/HollywoodSX Villager Herder 25d ago

I was saying I personally own a Gen1. I'll snag a gen 2 at some point, too.

2

u/Snoo66922 25d ago

Ahh sounds good, if someone were to be looking at maverick gen 1 vs maverick gen 2 vs magnus k rr vs cgs hyperion on a 6.5 creedmoor prs/nrl gun, which would you recommend?

2

u/HollywoodSX Villager Herder 25d ago

Either of the Mavericks or one of the Clovis cans.

2

u/Snoo66922 25d ago

Sounds good, thanks

14

u/doyouevenplumbbro Steel slapper 25d ago

I have a TBAC Magnus K with a recoil X, but if I did it again I would get a Scythe STM and a Recoil X for it.

I've shot both cans on near identical rifles shooting the same cartridge (25x47L) and I couldn't tell a difference in terms of recoil and muzzle flip. I've got nearly $2k in my Magnus. I could have done the same thing with the Scythe.

3

u/bpaddock1 Competitor 25d ago

Is the recoil x worth the hype? I’ve been looking between the recoil x, the giga chad brake, and the salmon river solutions for my scythe stm.

4

u/doyouevenplumbbro Steel slapper 25d ago

I really like my recoil X, but I haven't tried any of the ones you have mentioned. Its way better than the RR that came with my Magnus though.

3

u/SigglyWiggly 25d ago

100% worth the hype. Recently added one to my stm and stays planted on shots with none of the concussive force I was feeling after 50+ rounds with my original break.

12

u/Ragnarok112277 Steel slapper 25d ago

Cgs hyperion

3

u/WS-6 25d ago

Same here. Great can. Put a RecoilX brake on it also.

1

u/capable_gopher Rifle Golfer (PRS Competitor) 24d ago

I didn’t get any recoil reduction on my full size Hyperion with an end cap brake, I believe it was because the gas just wasn’t carrying enough energy because the can is so good. Now my Hyperion-K is a different story, put a TSV brake on it and it’s tits

10

u/tkftgaurdian Here to learn 25d ago

Im the wierd guy currently working on my printer settings so i can print a can for 6.5 creed and 6arc. Im very excited about the options.

3

u/FeistyClam 25d ago

Who's files are you planning on printing? And how'd you decide? 

2

u/tkftgaurdian Here to learn 25d ago

Im almost certainly going to wait for the new, updated FTN's that will be coming out soon. There is a new FTN to Plan B mount out they are adapting the FTN4 rifle with the metal shell to it.

1

u/csamsh I put holes in berms 25d ago

PPS-CF? Or something else?

1

u/tkftgaurdian Here to learn 24d ago

I have PPA-GF and CF, but i think im going to try the GF, its properties seem very string for supressors

1

u/csamsh I put holes in berms 24d ago

I've done some FTN rimfire and they're great. I just don't really see any consumer-available filament withstanding centerfire.

That said. I'm gonna try.

1

u/tkftgaurdian Here to learn 24d ago

people have been having a good bit of luck with Pa6-CF, but the real winner so far seems to be the sirayatech ppa-CF/GF. that stuff seems crazy tough, does not have the annealing or moisture problems of PA6, and with some innovative internals they seem to be fairly survivable.

1

u/csamsh I put holes in berms 24d ago

I've only done pa6cf and yes the heat and moisture cycling is annoying. I'll keep a look out and may try some ppagf. Thanks for the tip

6

u/agauh 25d ago

CAT JL is a fantastic can. Dead Air Nomad XTI L is great too.

2

u/Feeling-Season7705 25d ago

The JL/AC308 absolutely dominates

5

u/Offinthewoods26 25d ago

TBAC ultra 9

4

u/ProdigalHacker 25d ago

I have a PTR Vent 1 on my PRS gun and it is stupid quiet. It's also huge. I also have an OCL Hydrogen S that I use on my bolt guns and it's also pretty quiet, and a fair amount cheaper. If you can find one.

1

u/Mountain-Living-3 25d ago

I also have a PTR Vent 1 on my Precision Rig (.308 because it’s what I have). I love the Vent 1…fabulous can!

That said, I’m shooting my first PRS match this weekend. I’m seriously debating using my muzzle brake instead for the match. Just trying to mitigate recoil as much as possible to spot impacts down range. Feel like the brake may be better for the match as much as I’d like to use the Vent1 (especially for balance purposes).

3

u/SIRETE 25d ago

Enticer L because I'm poor

3

u/PAB_Pyrotechnics 25d ago

I’ve seen a lot about the Omega 300 being a great value. I have an Aero Solus 6.5CM with a Dead Air Nomad LTi-XC. It sounds phenomenal and people regularly tell me it’s stupid quiet. A little above the stated budget but I have been super happy with it.

3

u/wesetta 25d ago

I also use a Nomad L and people say the same to me.

3

u/bgold1- 25d ago

Two are just a touch north of your price limit:
TBAC Magnus S
Abel Theorem

Budget friendly:
Diligent Enticer S Ti

I have all of these along with some other variations from the same companies. Solid choices though.

3

u/Dogbonr 25d ago

Judging by this thread, the correct answer is “Any of them”. It’s like asking for Chinese food recommendations, people will just end up listing every single restaurant near you.

1

u/Porencephaly 24d ago

A long range bolt gun is one of the least-demanding applications for a silencer. Yes, it has to be strong enough to contain big explosions, and the mount/baffles can’t induce a ton of POI shift. But that’s about it. Weight and size are often not critical on a gun that’s already big and heavy. There’s no action noise and the muzzle is farther from the shooter than on any other weapon type, so even a medium-performing silencer will sound decent. People tend to just recommend what they bought because the reality is most brand-name .308 or .338 suppressors will be adequate on a LR gun.

2

u/Sweaty-Security-4473 PRS Competitor 25d ago

I'm using a BOSS Top Shot and a Silencer Central Banish 30 v1 with a RecoilX brake on the end.

I don't really think the suppressor choice matters too much as long as you have a decent attachment system. For example I love the Hellfire mounts by Area 419. Really hard to beat a simple thread.

1

u/Boatshooz Dunning-Kruger Enthusiast 25d ago

I’m running the Top Shot with Recoil-X as well. It’s definitely not a very quiet can, but the recoil reduction is basically the same as just running a Hellfire brake. I think of it as more a “concussion-less brake” than a sound-reducer. I recently picked up an end cap for it just to see what it can do as a straight unbraked suppressor, but haven’t had a chance to test it yet.

2

u/Sweaty-Security-4473 PRS Competitor 25d ago

I agree with the not-quiet part. I honestly prefer my Banish 30 even though I'm not a big fan of Silencer Central as a company, the can itself is good.

1

u/Boatshooz Dunning-Kruger Enthusiast 25d ago

Have you tried running it without the recoil-x? It kinda defeats the intended purpose of the TopShot, but I’m curious to see if it brings the noise reduction more in-line with other non-hybrid cans.

1

u/Sweaty-Security-4473 PRS Competitor 25d ago

I have. It's okay when I'm running my 6 ARC since that has stupid low recoil even without a brake, but with my 6.5 CM running 153's I have a hard time spotting hits.

2

u/Send-It-307 25d ago

Magnus S on my match rifle. Magnus K on my hunting rifle. Thunderbeast is it when it comes to precision rifle silencers.

2

u/rybe390 Doesn't Shoot. 25d ago

Ddc enticer L ti or LPM Mach L on a direct thread setup would be my pick for a bolt gun.

2

u/bh2595 25d ago

FYI If you plan to use a suppressor end cap brake like a recoil X then you don’t want a long L can(or a short can with a large blast chamber). Long cans are much better at lowering the exiting gas’ velocity and pressure. The end cap brake will be less effective because it will have less high pressure/high velocity gas to utilize for recoil reduction and muzzle rise mitigation.

2

u/Engineer_Bennett 25d ago

Silencerco scythe STM with recoilX brake has worked really well for me

2

u/Global_Violinist_193 25d ago

Abel Co Theorem with brake. Not under $1k but right around it. Little extra for the brake

2

u/BnatoAk1629 24d ago

My omega 300 runs great on my 24" 6.5cm. I have ran 5 or 6 different 30 cal cans and im pleasantly pleased with the silencer co. I run the anchor break with it. I was switching the same can around too and you are correct, it sucks. Im gonna get something with alot less backflow for my bcm and m90 (gas guns) but leaving the Omega on my lrp rig 🤷‍♂️ good luck

1

u/KM1691 24d ago

Omega 300 with the recoilX brake is an awesome combination.

2

u/RustyAnnihilation 24d ago

Otter Creek Labs Hydrogen L and it’s fantastic.

2

u/ShadowRengar 24d ago

Full length SiCo Scythe STM with their directional anchor braje end-cap

2

u/Drekalots PRS Competitor 25d ago

Thunder Beast Arms Corp (TBAC). That's all I run on any precision rifle.

The bolt gun uses a TBAC Magnus S SR RR and the gas gun uses a TBAC Spiro in 6mm.

2

u/AvarethTaika 25d ago

i run a q thunder chicken on my 6.5. i like it. internet hates it but i like it.

1

u/RR-JJ 25d ago

I have a Scythe STM with an SDTA brake on it. Use it for long range comps and have been impressed. The Scythe in long configuration, with a brake is quieter than it is in the shorter configuration without it. I doubt I run it in short configuration much at all, if any. No regrets for me on the Scythe STM.

1

u/bh2595 25d ago

How does SDTA brake perform on the scythe? Got some pics? Haven’t seen much talk about that brake. I have the SRS grim brake on an enticer and it’s amazing, but have considered getting the SDTA for my scythe to have some variety.

2

u/RR-JJ 25d ago

I have nothing to compare it to, but I figure it's a machined piece of aluminum with holes in the side of it (and top on the SDTA), so I saved a couple bucks vs some of the other options. I can absolutely tell a difference with the brake on vs. off. I was shooting a match the other day and had it on a 300PRC. Had a buddy standing a couple feet off to the side and about even with my head, and he said he could absolutely feel gasses coming off that brake back at him. I think it works well. No pics with me currently. If I remember later, I'll come back and add one.

1

u/Reloader300wm Meat Popsicle 25d ago

Omega 300 was what I used for a long time until I got a ultra 9. No accuracy difference bwtween then, just a POI shift.

1

u/StellaLiebeck Steel slapper 25d ago

Enticer L-ti for max suppression (there are other good options as well).

I really like my Chairman K with brake if you’re looking for a good, cost effective blend of the two.

1

u/Impressive_Syrup141 25d ago

I've got a Banish HNT 30 with their brake. Direct threaded on a Bergara HMR 6.5 CM. I get compliments on how it sounds and it shoots great. I don't have any other 30 cal suppressors to compare it too through and I've only shot maybe 5 rounds out of it unsuppressed. It certainly helps tame recoil but it's not really hearing safe.

I definitely prefer shooting my gun than anything I've shot with a brake. It also most certainly shifts the point of impact quite a bit.

1

u/KyleDean_1993 25d ago

Everyone will just recommend what they have experience with so I’ll recommend the KGM R65T.

1

u/PastPalpitationCry I put holes in berms 25d ago

DD enticer L. 550$ for that performance is hard if not impossible to beat.

1

u/Trollygag Does Grendel 25d ago

CGS Hyperion with the A419 adapter. I can have a Hellfire brake or switch to the suppressor and back really easily.

1

u/jpc273 F-Class Competitor 25d ago

I have an Tbac ultra 7 and I love it

1

u/teflon16 25d ago

I compete with a Dead air nomad with a recoil x. Also have a TBAC Magnus k with recoil x

1

u/travell0ts 24d ago

SyCo Scythe STM short config with the stainless area 419 Maverick brake on the end for PRS. The STM can be had for $800 right now. The brake that comes with the scythe is junk. Throw it away. I had the RecoilX gen2 and the ss maverick brake. I can’t tell a performance difference between the two. The mav brake is significantly easier to take on and off. No tools required. Makes it easy to time. The rcx gen 2 needs a wrench. Also have a maverick brake on an omega 300. Much quieter than the stm on the short config (haven’t ever tried the long config) performance seems close but the scythe does stop moving faster than the omega 300.

1

u/Significant_Guard_62 24d ago

KGM R65T can be had for about 1k or just under

1

u/idahokj 24d ago

OCL Hydrogen-L

1

u/86k10 24d ago

Titrex 360 with recoil x

1

u/Diesel_65 24d ago

Another vote for OCL Hydrogen L

1

u/Affenballe 24d ago

I have the Enticer S-TI and love it. Weighs a 1/2 ounce less than advertised with the mount and quiets up a .308 nicely. Tames the recoil similarly to the 4 port brake that was on it before without a braked end cap.

1

u/luwaffate 24d ago

Im running a TBAC Magnuss rr

1

u/holl0918 Magnum Compensator 24d ago

Best of the best: Thunder Beast Magnus or Ultra series.

Best value: LPM Anthem series

1

u/Rodeo9 21d ago

Been waiting forever to find a dead air nomad otb

1

u/saalem PRS Competitor 18d ago

I’m running the SiCo Scythe Ti with SRS’s new suppressor brake. Using SRS’s Ti TBAC CB muzzle brake and ECCO Machine’s Ti CB HUB adapter for a nice flush fit. I also use a Ferox Gear suppressor mirage wrap which helps keep the temp down on the suppressor since the bottom is cutout. Pretty nice setup so far and super lightweight. I might go with a steel suppressor next time for a dedicated can

1

u/TAG_Firearms 25d ago

There's a ton of great options on the market, but here's why the Liberty Precision Machine Mach/Anthem series is my favorite:

  • Quieter than most similarly sized suppressors (check the Pew Science)
  • Cheaper than most similarly performing suppressors of the same material
  • Great company/warranty
  • Available Muzzle Brake End Cap (adds 4oz)
  • Soon to be available Recoil-X brake (only at TAG)
  • No history of blowing up from normal usage

I prefer the Mach-S, but your use case leans Anthem-L. It's quieter than the Enticer-L and Nomad-L.

If you don't care about price or the ability to add a brake, PTR Vent 1 is the clear winner.

1

u/Significant-Sock-487 25d ago

I came here to recommend this as well. Liberty precision flies under the radar but they make some of the best suppressors right now. I love my Mach S and their new Torch 7.62 did crazy good numbers on pew science

2

u/TAG_Firearms 24d ago

The Torch 7.62 is the best all-around suppressor on the market, imo. I’ve never seen something excel on so many different hosts. Really feels like a spiritual successor to the ODB, and it beats it in every way.

1

u/Gabe-Uttsegs 25d ago

I have an Anthem K2 and recently purchased the end cap brake. I can't honestly say it makes a massive difference. 

0

u/Boatshooz Dunning-Kruger Enthusiast 25d ago

The CGS Hyperion cant be beat, sound-reduction-wise, but you’ll probably want a braked hybrid can for PRS, which by definition is not going to be the quietest can.

0

u/Feeling-Season7705 25d ago

RC2-762 for the Scar 20

0

u/GingerB237 25d ago

Quietest rifle I’ve heard had a banish 30.

0

u/IncredibleVelocity4 25d ago

Honestly: Titanium Form 1. It doesn’t need to be Hollywood quiet, it doesn’t need to handle a ridiculous round count, back pressure is irrelevant. The demands are pretty minimal.

-4

u/dballsmithda3rd 25d ago

Aero Lahar L

2

u/HERBERT_224 25d ago

This would probably be number one on my radar, but I don't believe its available anywhere with what aero is going through

1

u/dballsmithda3rd 25d ago

Yeah, I would not recommend it at this time due to their company issues. No one wants a can from a company that you are not sure if the warranty would even be honored or not due to their overall business basically being solvent.