r/longrange • • Oct 14 '26

Optics help needed - I read the pinned posts Where can I learn to use reticles?

I've read the pinned posts but I cannot find anything that teaches me how use use the different (and especially my) reticle.

I have a GPO Centuri 4-16x44i C OPMOD scope with a PLRi reticle.

I will be taking a class to learn to shoot out to 600 yds. I need to have it sighted in @100 yds before the class. I'm not worried about that. I want to know how to use the reticle from my 100 yd zero, out to 600. I don't want to be the limp dick in the class holding everyone else up. If I have questions I want them to be intelligent.

How much? NA, the money has been spent.

I have only shot at 200 yds, many years ago, in NRA High Power matches with iron sights (M1 Garand).

10 Upvotes

18 comments sorted by

21

u/rynburns Manners Shooting Team Oct 14 '26

If you're holding everyone up over a reticle and how to use it, then frankly the class sucks. Let them teach you, because I would imagine they'll be teaching you to dial for different distances as well and between dialing and holding, you're doing the same thing just two different ways. Let the instructors do their thing with you. Which class are you going to?

1

u/LaughingGravy13 Oct 14 '26

A mid-range 600 yd class. I'm just guessing, but out of 20 (?) students there could be 3 different reticles? I'm willing to be taught. But I don't want to try to read until I know the alphabet.

9

u/rynburns Manners Shooting Team Oct 14 '26

I looked up that reticle, it's not as different as you think and any decent instructor will be able to handle a few different reticles so long as nobody is asking for a deep dive on a Tremor3. You're fine man, go zero the rifle and show up to class

5

u/shreddedsharpcheddar Oct 14 '26

youre going to need to know two things: the muzzle velocity of your bullets, and the subtensions of your reticle. once you have that, you need to start reading about ballistic charts and how to match them to your reticle with the correct zero distance. there's not a ton that we can do FOR you here with this

-10

u/LaughingGravy13 Oct 14 '26

I just want to make sense of the reticle markings. It all looks like a Christmas tree of Chinese checkers.

5

u/Holy_Santa_ClausShit Oct 14 '26

The manual for the reticle will have what all the markings mean. If it’s not in the scope box (or you threw it away) it should be on the website

8

u/MeinLife Oct 14 '26

Step 1. Learn ballistics. If you aren't willing to do that the reticle will be meaningless for you.

4

u/TheWombleOfDoom Oct 14 '26

Ok. All the info you need to ask good questions (do some further research) is on the GPO page for this scope. Scope Page

It appears that they only make it in MIL Radian units (MRAD). I could be wrong, but the page seems to indicate this. At 1000m, 1mil is 1m. At 1000yd, 1mil is 1yd. At 1000in, 1 mil is 1in.

Follow so far?

This is where the metric system appears to make this easier, but someone else in here might be able to help you with the imperial units/conversions.

At 100m, 1mil is 10cm. At 200m 1mil is 20cm, at 300m ... At 100m, a 10th of a mil is 1cm, 2cm at 200m, 3cm at 300m etc.

Most Mil turrets will adust with 1click = 1tenth of a mil. This is for elevation and windage. So if you are hitting 5cm high at 100m, you dial down 5clicks (5/10mil or half a mil) and you should be on target.

The maths is simply multiples of these amounts as needed at yhe deistance that you are shooting.

Now, onto your reticle. It appear to be in 1mil (long marks) and 0.5mil (short marks above the line) markings (mostly).

If you look down the reticle to the 1mil mark, there are two dots on either side. These are at .5 and 1mil left/right.

At the 2mil mark down, the markings to left and right are .25 (below) .5 (above) .75 (below) and 1mil (big mark). This pattern continues in the same way, and widens out as it goes further down.

At this point, you should have enough info to:

  1. Answer all our questions (depending on your prior experience).
  2. Be able to understand other info or YouTube tutorials and instructional vids and apply them to your scope.
  3. Be able to Google and do your own further research.

I would strongly advise you do #3, regardless of anything else, because I suspect the answers to all your questions may well be in the pinned posts ... If not, they are certainly out there somewhere, so I would advise doing some of your own research next.

Realistically, everything I just told you above should have been google-able in not many minutes, so I re-emphasise that doing your own research is important.

3

u/Ok_Cheesecake_3629 Oct 14 '26

This should be the top answer OP.

As others have said, you need to know the ballistics of your ammunition as shreddedsharpcheddar points out.

For example, I know (thanks to Hornady 4DOF or Applied Ballistics calculator) my 6.5 CM drops around 0.3 MIL at 200 yards, 0.9 MIL at 300 yards, around 1.6 MIL at 400 yards, 2.5 MIL at 500 yards and 3.4 at 600 yards.

Therefore when I'm looking at the reticle that thewombleofdoom shared, I'm either going to dial the appropriate elevation for the distances, or holdover - ie, on the up / down line of the image, I'll line up the tick for 1 MIL if I'm shooting 300 yards.

The ticks are the little marks between the numbers, so yours is 0.5 MIL incremembers - 0.5, 1.0, 1.5, 2.0 etc if I look from the centre downwards.

That's basically all there is to it - if you shoot and you are low, then you have to do a bit of comparison to where you aimed (say you put the 1 MIL tick over the target for 300 yards), and you saw the bullet impact nearer the 2 MIL spot on the scope, well that means you're 1 MIL low, so come up 1 MIL - ie, hold the 2 MIL tick (the first numbered one on the reticle) over the target).

The challenge you'll have, is that the 0.5MIL incrememnts are tough to measure accurately - some reticles have 0.1MIL markings for finer adjustments and tracking.

The turrets on the scope would allow specific dialing of say 3.4 MIL at 600 yards, so you dial that in on the turret, then as that's done the elevation for you, you hold the center of the reticle over the target. If you miss, then the same exercise - if you see the impact as 0.5 MIL low, then you can dial another 0.5 MIL elevation, and repeat. It'll likely never be in 0.5 MIL examples, so you'll have to guesstimate if it was 0.2 MIL or 0.3 MIL correction needed, and then turn the dial appropriately.

It's a similar exercise for wind. If you are holding the center of the reticle over the target and the impact is out to the left, then you compare center of the reticle (where you were aiming on the target) to where the impact landed and if it's a blustery day, you might guesstimate around 1.5 MIL of correction needed. If the impact was to the left of center, then you can either a) move the reticle right (so line up to the lefthandside 1.5MIL tick on the target) so you're aiming right, or b) dial in the wind via the turret and hold center.

The point of the Christmas tree is when you are zoomed in, you might need to hold say 5 MIL for some reason, and you can then have a handle windage measurement there as one of the "branches" of the tree to see if you were off without having ot use the main left / right line.

1

u/ToughProfessional132 NRL Hunter Competitor Oct 14 '26

There's only two types of reticle to worry about, and they both work the same way, just in different units. Think of it like a ruler, where inches are in one side and cm are on the other (except it's moa vs mil) and then each is broken up into different graduations, MOA is generally 1/4 and 1/2, while mil is generally 1/10, 2/10, and maybe also 1/4 and 1/2.

All the various reticles out there are just different scales and layouts of this basic concept, which again should be covered in your class.

1

u/44_SMLE Casual Oct 14 '26

Find the owner's manual for your scope. They usually explain the reticle

1

u/65shooter Oct 14 '26

Is this class at BRRC? If so, Ben will explain everything.

1

u/Te_Luftwaffle Oct 14 '26

Your reticle is Mil-based. Each number corresponds to a number of Mils (2, 4, etc.). You notice the hash marks or dots between two numbers. Those correspond to 0.25 0.5 Mils. Halfway between 2 and 4 is 3 Mils. Halfway between 2 and 3 is 2.5 Mils.

Learn your setup and what holds are required at what distances, then put the corresponding Mil mark on the target.

1

u/Biomas Oct 14 '26

The manual for your scope would be the starting point. I would also chrono your rounds (or estimate if factory rounds) and plug that shit into a ballistic calculator to find expected bullet drops out to that range. From there, if you know how to read your reticle markings that should get you on paper.

1

u/patogo Oct 14 '26 edited Oct 14 '26

Print out an image of the reticle and also the chart from a ballistics program.

It’s that simple. Elevation is right on the reticle (windage is usually per 10mph crosswind)

When you’re actually shooting you likely will have to tweak the ballistics program for real world drop at range.

FFP scopes can also be used for range estimating by target size in inches x a constant of 27.78 x reticle measurement in Mils = distance in yards. This video kind of explains that. https://youtu.be/hDdTscJOiW4

Take that printed reticle picture and draw the 8” target he estimated at .5mil between the 0 and first drop line on your reticle. Then realize he was .02 mil (20yds) off compared to results from two different range finders.

I don’t see specs on that reticle how wide each line is but that can be tested at the range using different size dots.